Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -325,11 +325,8 @@
325	325	** DO1 is high in case there is load between DO1 and V+.
326	326	** DO1 LED is off in both case
327	327
328		-
329		-
330	330	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
331	331
332		-
333	333	**For LT-22222-L**: this mode the **DI1 and DI2** are used as counting pins.
334	334
335	335	(((
...	...	@@ -338,7 +338,6 @@
338	338
339	339	[[image:image-20220523180452-3.png]]
340	340
341		-
342	342	(((
343	343	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DO3, DO2 and DO1. Totally 1bytes as below
344	344	)))
...	...	@@ -354,8 +354,6 @@
354	354	)))
355	355
356	356	(((
357		-
358		-
359	359	**To use counting mode, please run:**
360	360	)))
361	361
...	...	@@ -374,8 +374,6 @@
374	374	)))
375	375
376	376	(((
377		-
378		-
379	379	(% style="color:#4f81bd" %)**AT Commands for counting:**
380	380	)))
381	381
...	...	@@ -472,9 +472,9 @@
472	472	)))
473	473
474	474
	467	+
475	475	=== 3.3.4 AT+MOD~=4, Single DI Counting + 1 x Voltage Counting ===
476	476
477		-
478	478	**LT22222-L**: This mode the DI1 is used as a counting pin.
479	479
480	480	The AVI1 is also used for counting. AVI1 is used to monitor the voltage. It will check the voltage **every 60s**, if voltage is higher or lower than VOLMAX mV, the AVI1 Counting increase 1, so AVI1 counting can be used to measure a machine working hour.
...	...	@@ -481,7 +481,6 @@
481	481
482	482	[[image:image-20220523181903-8.png]]
483	483
484		-
485	485	(((
486	486	(% style="color:#4f81bd" %)**DIDORO **(%%)is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
487	487	)))
...	...	@@ -497,8 +497,6 @@
497	497	)))
498	498
499	499	(((
500		-
501		-
502	502	**To use this mode, please run:**
503	503	)))
504	504
...	...	@@ -525,8 +525,6 @@
525	525	)))
526	526
527	527	(((
528		-
529		-
530	530	**Plus below command for AVI1 Counting:**
531	531	)))
532	532
...	...	@@ -562,14 +562,11 @@
562	562
563	563	=== 3.3.5 AT+MOD~=5, Single DI Counting + 2 x AVI + 1 x ACI ===
564	564
565		-
566	566	**LT22222-L**: This mode the DI1 is used as a counting pin.
567	567
568	568	[[image:image-20220523182334-9.png]]
569	569
570	570	(((
571		-
572		-
573	573	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
574	574	)))
575	575
...	...	@@ -584,8 +584,6 @@
584	584	)))
585	585
586	586	(((
587		-
588		-
589	589	**To use this mode, please run:**
590	590	)))
591	591
...	...	@@ -605,6 +605,8 @@
605	605
606	606	(((
607	607	Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
	590	+
	591	+
608	608	)))
609	609
610	610
...	...	@@ -611,7 +611,6 @@
611	611
612	612	=== 3.3.6 AT+ADDMOD~=6. (Trigger Mode, Optional) ===
613	613
614		-
615	615	(% style="color:#4f81bd" %)**This mode is an optional mode for trigger purpose. It can run together with other mode.**
616	616
617	617	For example, if user has configured below commands:
...	...	@@ -619,13 +619,11 @@
619	619	* **AT+MOD=1 ** **~-~->** The normal working mode
620	620	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
621	621
622		-
623	623	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
624	624
625	625	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
626	626	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
627	627
628		-
629	629	**AT Command to set Trigger Condition**:
630	630
631	631	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -677,12 +677,10 @@
677	677
678	678	Yy4 yy4: AC2 or AV2 high limit.
679	679
680		-
681	681	**Example1**: AA 00 13 88 00 00 00 00 00 00
682	682
683	683	Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
684	684
685		-
686	686	**Example2**: AA 02 01 00
687	687
688	688	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
...	...	@@ -725,7 +725,6 @@
725	725
726	726	* Each bits shows which status has been trigger on this uplink.
727	727
728		-
729	729	**Example:**
730	730
731	731	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -746,8 +746,6 @@
746	746	=== 3.3.7 Payload Decoder ===
747	747
748	748	(((
749		-
750		-
751	751	**Decoder for TTN/loraserver/ChirpStack**: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/Payload_decoder/>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/Payload_decoder/]]
752	752
753	753