Changes for page LT-22222-L -- LoRa I/O Controller User Manual
Last modified by Saxer Lin on 2025/04/15 17:24
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -275,6 +275,7 @@ 275 275 * **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO 276 276 * **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5 277 277 278 + 278 278 === 3.3.1 AT+MOD~=1, 2ACI+2AVI === 279 279 280 280 The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default. ... ... @@ -282,6 +282,8 @@ 282 282 [[image:image-20220523174024-3.png]] 283 283 284 284 ((( 286 + 287 + 285 285 (% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below 286 286 ))) 287 287 ... ... @@ -295,6 +295,7 @@ 295 295 296 296 For example if payload is: [[image:image-20220523175847-2.png]] 297 297 301 + 298 298 **The value for the interface is: ** 299 299 300 300 AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V ... ... @@ -325,6 +325,7 @@ 325 325 ** DO1 is high in case there is load between DO1 and V+. 326 326 ** DO1 LED is off in both case 327 327 332 + 328 328 === 3.3.2 AT+MOD~=2, (Double DI Counting) === 329 329 330 330 ... ... @@ -624,6 +624,7 @@ 624 624 1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.** 625 625 626 626 632 + 627 627 **AT Command to set Trigger Condition**: 628 628 629 629 (% style="color:#4f81bd" %)**Trigger base on voltage**: ... ... @@ -637,6 +637,7 @@ 637 637 AT+AVLIM=5000,0,0,0 (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore) 638 638 639 639 646 + 640 640 (% style="color:#4f81bd" %)**Trigger base on current**: 641 641 642 642 Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH> ... ... @@ -646,6 +646,7 @@ 646 646 AT+ACLIM=10000,15000,0,0 (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink) 647 647 648 648 656 + 649 649 (% style="color:#4f81bd" %)**Trigger base on DI status**: 650 650 651 651 DI status trigger Flag. ... ... @@ -652,12 +652,13 @@ 652 652 653 653 Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG > 654 654 663 + 655 655 **Example:** 656 656 657 657 AT+ DTRI =1,0 (Enable DI1 trigger / disable DI2 trigger) 658 658 659 659 660 -**Downlink Command to set Trigger Condition** 669 +**Downlink Command to set Trigger Condition:** 661 661 662 662 Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM** 663 663 ... ... @@ -686,6 +686,7 @@ 686 686 Same as AT+ DTRI =1,0 (Enable DI1 trigger / disable DI2 trigger) 687 687 688 688 698 + 689 689 (% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:** 690 690 691 691 MOD6 Payload : total 11 bytes payload ... ... @@ -700,6 +700,7 @@ 700 700 * Each bits shows if the corresponding trigger has been configured. 701 701 702 702 713 + 703 703 **Example:** 704 704 705 705 10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW ... ... @@ -712,6 +712,7 @@ 712 712 * Each bits shows which status has been trigger on this uplink. 713 713 714 714 726 + 715 715 **Example:** 716 716 717 717 10000000: Means this packet is trigger by AC1_LOW. Means voltage too low. ... ... @@ -724,6 +724,7 @@ 724 724 * Each bits shows which status has been trigger on this uplink. 725 725 726 726 739 + 727 727 **Example:** 728 728 729 729 00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.