Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -467,7 +467,6 @@
467	467
468	468	=== 3.3.4 AT+MOD~=4, Single DI Counting + 1 x Voltage Counting ===
469	469
470		-
471	471	**LT22222-L**: This mode the DI1 is used as a counting pin.
472	472
473	473	The AVI1 is also used for counting. AVI1 is used to monitor the voltage. It will check the voltage **every 60s**, if voltage is higher or lower than VOLMAX mV, the AVI1 Counting increase 1, so AVI1 counting can be used to measure a machine working hour.
...	...	@@ -474,7 +474,6 @@
474	474
475	475	[[image:image-20220523181903-8.png]]
476	476
477		-
478	478	(((
479	479	(% style="color:#4f81bd" %)**DIDORO **(%%)is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
480	480	)))
...	...	@@ -490,8 +490,6 @@
490	490	)))
491	491
492	492	(((
493		-
494		-
495	495	**To use this mode, please run:**
496	496	)))
497	497
...	...	@@ -518,8 +518,6 @@
518	518	)))
519	519
520	520	(((
521		-
522		-
523	523	**Plus below command for AVI1 Counting:**
524	524	)))
525	525
...	...	@@ -555,14 +555,11 @@
555	555
556	556	=== 3.3.5 AT+MOD~=5, Single DI Counting + 2 x AVI + 1 x ACI ===
557	557
558		-
559	559	**LT22222-L**: This mode the DI1 is used as a counting pin.
560	560
561	561	[[image:image-20220523182334-9.png]]
562	562
563	563	(((
564		-
565		-
566	566	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
567	567	)))
568	568
...	...	@@ -577,8 +577,6 @@
577	577	)))
578	578
579	579	(((
580		-
581		-
582	582	**To use this mode, please run:**
583	583	)))
584	584
...	...	@@ -598,6 +598,8 @@
598	598
599	599	(((
600	600	Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
	590	+
	591	+
601	601	)))
602	602
603	603
...	...	@@ -611,13 +611,11 @@
611	611	* **AT+MOD=1 ** **~-~->** The normal working mode
612	612	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
613	613
614		-
615	615	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
616	616
617	617	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
618	618	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
619	619
620		-
621	621	**AT Command to set Trigger Condition**:
622	622
623	623	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -669,17 +669,14 @@
669	669
670	670	Yy4 yy4: AC2 or AV2 high limit.
671	671
672		-
673	673	**Example1**: AA 00 13 88 00 00 00 00 00 00
674	674
675	675	Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
676	676
677		-
678	678	**Example2**: AA 02 01 00
679	679
680	680	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
681	681
682		-
683	683	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
684	684
685	685	MOD6 Payload : total 11 bytes payload
...	...	@@ -686,7 +686,6 @@
686	686
687	687	[[image:image-20220524085923-1.png]]
688	688
689		-
690	690	(% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if trigger is set for this part. Totally 1byte as below
691	691
692	692	[[image:image-20220524090106-2.png]]
...	...	@@ -693,7 +693,6 @@
693	693
694	694	* Each bits shows if the corresponding trigger has been configured.
695	695
696		-
697	697	**Example:**
698	698
699	699	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -705,7 +705,6 @@
705	705
706	706	* Each bits shows which status has been trigger on this uplink.
707	707
708		-
709	709	**Example:**
710	710
711	711	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -717,7 +717,6 @@
717	717
718	718	* Each bits shows which status has been trigger on this uplink.
719	719
720		-
721	721	**Example:**
722	722
723	723	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.