Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -488,8 +488,6 @@
488	488	)))
489	489
490	490	(((
491		-
492		-
493	493	**To use this mode, please run:**
494	494	)))
495	495
...	...	@@ -516,8 +516,6 @@
516	516	)))
517	517
518	518	(((
519		-
520		-
521	521	**Plus below command for AVI1 Counting:**
522	522	)))
523	523
...	...	@@ -553,14 +553,11 @@
553	553
554	554	=== 3.3.5 AT+MOD~=5, Single DI Counting + 2 x AVI + 1 x ACI ===
555	555
556		-
557	557	**LT22222-L**: This mode the DI1 is used as a counting pin.
558	558
559	559	[[image:image-20220523182334-9.png]]
560	560
561	561	(((
562		-
563		-
564	564	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
565	565	)))
566	566
...	...	@@ -575,8 +575,6 @@
575	575	)))
576	576
577	577	(((
578		-
579		-
580	580	**To use this mode, please run:**
581	581	)))
582	582
...	...	@@ -596,6 +596,8 @@
596	596
597	597	(((
598	598	Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
	590	+
	591	+
599	599	)))
600	600
601	601
...	...	@@ -609,13 +609,11 @@
609	609	* **AT+MOD=1 ** **~-~->** The normal working mode
610	610	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
611	611
612		-
613	613	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
614	614
615	615	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
616	616	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
617	617
618		-
619	619	**AT Command to set Trigger Condition**:
620	620
621	621	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -667,17 +667,14 @@
667	667
668	668	Yy4 yy4: AC2 or AV2 high limit.
669	669
670		-
671	671	**Example1**: AA 00 13 88 00 00 00 00 00 00
672	672
673	673	Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
674	674
675		-
676	676	**Example2**: AA 02 01 00
677	677
678	678	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
679	679
680		-
681	681	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
682	682
683	683	MOD6 Payload : total 11 bytes payload
...	...	@@ -684,7 +684,6 @@
684	684
685	685	[[image:image-20220524085923-1.png]]
686	686
687		-
688	688	(% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if trigger is set for this part. Totally 1byte as below
689	689
690	690	[[image:image-20220524090106-2.png]]
...	...	@@ -691,7 +691,6 @@
691	691
692	692	* Each bits shows if the corresponding trigger has been configured.
693	693
694		-
695	695	**Example:**
696	696
697	697	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -703,7 +703,6 @@
703	703
704	704	* Each bits shows which status has been trigger on this uplink.
705	705
706		-
707	707	**Example:**
708	708
709	709	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -715,7 +715,6 @@
715	715
716	716	* Each bits shows which status has been trigger on this uplink.
717	717
718		-
719	719	**Example:**
720	720
721	721	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -756,7 +756,6 @@
756	756	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
757	757
758	758
759		-
760	760	=== 3.4.1 Common Commands ===
761	761
762	762	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
...	...	@@ -1123,7 +1123,7 @@
1123	1123
1124	1124
1125	1125
1126		-==== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ====
	1109	+=== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ===
1127	1127
1128	1128	* AT Command:
1129	1129