Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -554,8 +554,6 @@
554	554	[[image:image-20220523182334-9.png]]
555	555
556	556	(((
557		-
558		-
559	559	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
560	560	)))
561	561
...	...	@@ -570,8 +570,6 @@
570	570	)))
571	571
572	572	(((
573		-
574		-
575	575	**To use this mode, please run:**
576	576	)))
577	577
...	...	@@ -591,6 +591,8 @@
591	591
592	592	(((
593	593	Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
	590	+
	591	+
594	594	)))
595	595
596	596
...	...	@@ -604,13 +604,11 @@
604	604	* **AT+MOD=1 ** **~-~->** The normal working mode
605	605	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
606	606
607		-
608	608	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
609	609
610	610	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
611	611	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
612	612
613		-
614	614	**AT Command to set Trigger Condition**:
615	615
616	616	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -662,17 +662,14 @@
662	662
663	663	Yy4 yy4: AC2 or AV2 high limit.
664	664
665		-
666	666	**Example1**: AA 00 13 88 00 00 00 00 00 00
667	667
668	668	Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
669	669
670		-
671	671	**Example2**: AA 02 01 00
672	672
673	673	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
674	674
675		-
676	676	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
677	677
678	678	MOD6 Payload : total 11 bytes payload
...	...	@@ -679,7 +679,6 @@
679	679
680	680	[[image:image-20220524085923-1.png]]
681	681
682		-
683	683	(% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if trigger is set for this part. Totally 1byte as below
684	684
685	685	[[image:image-20220524090106-2.png]]
...	...	@@ -686,7 +686,6 @@
686	686
687	687	* Each bits shows if the corresponding trigger has been configured.
688	688
689		-
690	690	**Example:**
691	691
692	692	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -698,7 +698,6 @@
698	698
699	699	* Each bits shows which status has been trigger on this uplink.
700	700
701		-
702	702	**Example:**
703	703
704	704	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -710,7 +710,6 @@
710	710
711	711	* Each bits shows which status has been trigger on this uplink.
712	712
713		-
714	714	**Example:**
715	715
716	716	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -749,9 +749,8 @@
749	749	* (% style="color:#4f81bd" %)**Common Commands**(%%): They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
750	750
751	751	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
	741	+*
752	752
753		-
754		-
755	755	=== 3.4.1 Common Commands ===
756	756
757	757	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
...	...	@@ -1118,7 +1118,7 @@
1118	1118
1119	1119
1120	1120
1121		-==== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ====
	1109	+=== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ===
1122	1122
1123	1123	* AT Command:
1124	1124