<
From version < 77.79 >
edited by Xiaoling
on 2022/06/10 09:25
To version < 77.66 >
edited by Xiaoling
on 2022/06/10 09:19
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -554,8 +554,6 @@
554 554  [[image:image-20220523182334-9.png]]
555 555  
556 556  (((
557 -
558 -
559 559  (% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
560 560  )))
561 561  
... ... @@ -570,8 +570,6 @@
570 570  )))
571 571  
572 572  (((
573 -
574 -
575 575  **To use this mode, please run:**
576 576  )))
577 577  
... ... @@ -591,6 +591,8 @@
591 591  
592 592  (((
593 593  Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
590 +
591 +
594 594  )))
595 595  
596 596  
... ... @@ -604,13 +604,11 @@
604 604  * **AT+MOD=1 ** **~-~->** The normal working mode
605 605  * **AT+ADDMOD6=1**   **~-~->** Enable trigger
606 606  
607 -
608 608  LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
609 609  
610 610  1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
611 611  1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
612 612  
613 -
614 614  **AT Command to set Trigger Condition**:
615 615  
616 616  (% style="color:#4f81bd" %)**Trigger base on voltage**:
... ... @@ -662,17 +662,14 @@
662 662  
663 663   Yy4 yy4: AC2 or AV2 high limit.
664 664  
665 -
666 666  **Example1**: AA 00 13 88 00 00 00 00 00 00
667 667  
668 668  Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
669 669  
670 -
671 671  **Example2**: AA 02 01 00
672 672  
673 673  Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
674 674  
675 -
676 676  (% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
677 677  
678 678  MOD6 Payload : total 11 bytes payload
... ... @@ -679,7 +679,6 @@
679 679  
680 680  [[image:image-20220524085923-1.png]]
681 681  
682 -
683 683  (% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if trigger is set for this part. Totally 1byte as below
684 684  
685 685  [[image:image-20220524090106-2.png]]
... ... @@ -686,7 +686,6 @@
686 686  
687 687  * Each bits shows if the corresponding trigger has been configured.
688 688  
689 -
690 690  **Example:**
691 691  
692 692  10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
... ... @@ -698,7 +698,6 @@
698 698  
699 699  * Each bits shows which status has been trigger on this uplink.
700 700  
701 -
702 702  **Example:**
703 703  
704 704  10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
... ... @@ -710,7 +710,6 @@
710 710  
711 711  * Each bits shows which status has been trigger on this uplink.
712 712  
713 -
714 714  **Example:**
715 715  
716 716  00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
... ... @@ -750,8 +750,6 @@
750 750  
751 751  * (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
752 752  
753 -
754 -
755 755  === 3.4.1 Common Commands ===
756 756  
757 757  They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
... ... @@ -1118,7 +1118,7 @@
1118 1118  
1119 1119  
1120 1120  
1121 -==== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ====
1108 +=== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ===
1122 1122  
1123 1123  * AT Command:
1124 1124  
Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0