Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -587,6 +587,8 @@
587	587
588	588	(((
589	589	Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
	590	+
	591	+
590	590	)))
591	591
592	592
...	...	@@ -600,13 +600,11 @@
600	600	* **AT+MOD=1 ** **~-~->** The normal working mode
601	601	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
602	602
603		-
604	604	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
605	605
606	606	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
607	607	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
608	608
609		-
610	610	**AT Command to set Trigger Condition**:
611	611
612	612	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -658,17 +658,14 @@
658	658
659	659	Yy4 yy4: AC2 or AV2 high limit.
660	660
661		-
662	662	**Example1**: AA 00 13 88 00 00 00 00 00 00
663	663
664	664	Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
665	665
666		-
667	667	**Example2**: AA 02 01 00
668	668
669	669	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
670	670
671		-
672	672	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
673	673
674	674	MOD6 Payload : total 11 bytes payload
...	...	@@ -675,7 +675,6 @@
675	675
676	676	[[image:image-20220524085923-1.png]]
677	677
678		-
679	679	(% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if trigger is set for this part. Totally 1byte as below
680	680
681	681	[[image:image-20220524090106-2.png]]
...	...	@@ -682,7 +682,6 @@
682	682
683	683	* Each bits shows if the corresponding trigger has been configured.
684	684
685		-
686	686	**Example:**
687	687
688	688	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -694,7 +694,6 @@
694	694
695	695	* Each bits shows which status has been trigger on this uplink.
696	696
697		-
698	698	**Example:**
699	699
700	700	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -706,7 +706,6 @@
706	706
707	707	* Each bits shows which status has been trigger on this uplink.
708	708
709		-
710	710	**Example:**
711	711
712	712	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -747,7 +747,6 @@
747	747	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
748	748
749	749
750		-
751	751	=== 3.4.1 Common Commands ===
752	752
753	753	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
...	...	@@ -1114,7 +1114,7 @@
1114	1114
1115	1115
1116	1116
1117		-==== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ====
	1109	+=== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ===
1118	1118
1119	1119	* AT Command:
1120	1120