Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -602,13 +602,11 @@
602	602	* **AT+MOD=1 ** **~-~->** The normal working mode
603	603	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
604	604
605		-
606	606	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
607	607
608	608	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
609	609	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
610	610
611		-
612	612	**AT Command to set Trigger Condition**:
613	613
614	614	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -660,17 +660,14 @@
660	660
661	661	Yy4 yy4: AC2 or AV2 high limit.
662	662
663		-
664	664	**Example1**: AA 00 13 88 00 00 00 00 00 00
665	665
666	666	Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
667	667
668		-
669	669	**Example2**: AA 02 01 00
670	670
671	671	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
672	672
673		-
674	674	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
675	675
676	676	MOD6 Payload : total 11 bytes payload
...	...	@@ -677,7 +677,6 @@
677	677
678	678	[[image:image-20220524085923-1.png]]
679	679
680		-
681	681	(% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if trigger is set for this part. Totally 1byte as below
682	682
683	683	[[image:image-20220524090106-2.png]]
...	...	@@ -684,7 +684,6 @@
684	684
685	685	* Each bits shows if the corresponding trigger has been configured.
686	686
687		-
688	688	**Example:**
689	689
690	690	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -696,7 +696,6 @@
696	696
697	697	* Each bits shows which status has been trigger on this uplink.
698	698
699		-
700	700	**Example:**
701	701
702	702	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -708,7 +708,6 @@
708	708
709	709	* Each bits shows which status has been trigger on this uplink.
710	710
711		-
712	712	**Example:**
713	713
714	714	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -747,9 +747,8 @@
747	747	* (% style="color:#4f81bd" %)**Common Commands**(%%): They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
748	748
749	749	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
	741	+*
750	750
751		-
752		-
753	753	=== 3.4.1 Common Commands ===
754	754
755	755	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
...	...	@@ -1116,7 +1116,7 @@
1116	1116
1117	1117
1118	1118
1119		-==== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ====
	1109	+=== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ===
1120	1120
1121	1121	* AT Command:
1122	1122