Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -607,7 +607,6 @@
607	607	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
608	608	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
609	609
610		-
611	611	**AT Command to set Trigger Condition**:
612	612
613	613	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -659,17 +659,14 @@
659	659
660	660	Yy4 yy4: AC2 or AV2 high limit.
661	661
662		-
663	663	**Example1**: AA 00 13 88 00 00 00 00 00 00
664	664
665	665	Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
666	666
667		-
668	668	**Example2**: AA 02 01 00
669	669
670	670	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
671	671
672		-
673	673	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
674	674
675	675	MOD6 Payload : total 11 bytes payload
...	...	@@ -676,7 +676,6 @@
676	676
677	677	[[image:image-20220524085923-1.png]]
678	678
679		-
680	680	(% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if trigger is set for this part. Totally 1byte as below
681	681
682	682	[[image:image-20220524090106-2.png]]
...	...	@@ -683,7 +683,6 @@
683	683
684	684	* Each bits shows if the corresponding trigger has been configured.
685	685
686		-
687	687	**Example:**
688	688
689	689	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -695,7 +695,6 @@
695	695
696	696	* Each bits shows which status has been trigger on this uplink.
697	697
698		-
699	699	**Example:**
700	700
701	701	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -707,7 +707,6 @@
707	707
708	708	* Each bits shows which status has been trigger on this uplink.
709	709
710		-
711	711	**Example:**
712	712
713	713	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -748,7 +748,6 @@
748	748	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
749	749
750	750
751		-
752	752	=== 3.4.1 Common Commands ===
753	753
754	754	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
...	...	@@ -1115,7 +1115,7 @@
1115	1115
1116	1116
1117	1117
1118		-==== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ====
	1109	+=== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ===
1119	1119
1120	1120	* AT Command:
1121	1121