Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -607,7 +607,6 @@
607	607	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
608	608	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
609	609
610		-
611	611	**AT Command to set Trigger Condition**:
612	612
613	613	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -659,17 +659,14 @@
659	659
660	660	Yy4 yy4: AC2 or AV2 high limit.
661	661
662		-
663	663	**Example1**: AA 00 13 88 00 00 00 00 00 00
664	664
665	665	Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
666	666
667		-
668	668	**Example2**: AA 02 01 00
669	669
670	670	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
671	671
672		-
673	673	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
674	674
675	675	MOD6 Payload : total 11 bytes payload
...	...	@@ -676,7 +676,6 @@
676	676
677	677	[[image:image-20220524085923-1.png]]
678	678
679		-
680	680	(% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if trigger is set for this part. Totally 1byte as below
681	681
682	682	[[image:image-20220524090106-2.png]]
...	...	@@ -683,7 +683,6 @@
683	683
684	684	* Each bits shows if the corresponding trigger has been configured.
685	685
686		-
687	687	**Example:**
688	688
689	689	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -695,7 +695,6 @@
695	695
696	696	* Each bits shows which status has been trigger on this uplink.
697	697
698		-
699	699	**Example:**
700	700
701	701	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -707,7 +707,6 @@
707	707
708	708	* Each bits shows which status has been trigger on this uplink.
709	709
710		-
711	711	**Example:**
712	712
713	713	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -747,8 +747,6 @@
747	747
748	748	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
749	749
750		-
751		-
752	752	=== 3.4.1 Common Commands ===
753	753
754	754	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
...	...	@@ -770,7 +770,6 @@
770	770
771	771	**Example: **AT+TDC=30000. Means set interval to 30 seconds
772	772
773		-
774	774	* Downlink Payload (prefix 0x01):
775	775
776	776	(% class="box infomessage" %)
...	...	@@ -793,7 +793,6 @@
793	793
794	794	**Example**: AT+MOD=2. Set work mode to Double DI counting mode
795	795
796		-
797	797	* Downlink Payload (prefix 0x0A):
798	798
799	799	(% class="box infomessage" %)
...	...	@@ -809,7 +809,6 @@
809	809
810	810	There is no AT Command to poll uplink
811	811
812		-
813	813	* Downlink Payload (prefix 0x08):
814	814
815	815	(% class="box infomessage" %)
...	...	@@ -836,7 +836,6 @@
836	836
837	837	0: Disable Trigger Mode
838	838
839		-
840	840	* Downlink Payload (prefix 0x0A 06):
841	841
842	842	(% class="box infomessage" %)
...	...	@@ -854,7 +854,6 @@
854	854
855	855	There is no AT Command for this feature.
856	856
857		-
858	858	* Downlink Payload (prefix 0x AB 06):
859	859
860	860	(% class="box infomessage" %)
...	...	@@ -875,7 +875,6 @@
875	875	**Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >**
876	876	)))
877	877
878		-
879	879	**Example:**
880	880
881	881	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
...	...	@@ -1115,7 +1115,7 @@
1115	1115
1116	1116
1117	1117
1118		-==== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ====
	1102	+=== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ===
1119	1119
1120	1120	* AT Command:
1121	1121