Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -666,7 +666,6 @@
666	666
667	667	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
668	668
669		-
670	670	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
671	671
672	672	MOD6 Payload : total 11 bytes payload
...	...	@@ -673,7 +673,6 @@
673	673
674	674	[[image:image-20220524085923-1.png]]
675	675
676		-
677	677	(% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if trigger is set for this part. Totally 1byte as below
678	678
679	679	[[image:image-20220524090106-2.png]]
...	...	@@ -680,7 +680,6 @@
680	680
681	681	* Each bits shows if the corresponding trigger has been configured.
682	682
683		-
684	684	**Example:**
685	685
686	686	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -692,7 +692,6 @@
692	692
693	693	* Each bits shows which status has been trigger on this uplink.
694	694
695		-
696	696	**Example:**
697	697
698	698	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -743,8 +743,6 @@
743	743
744	744	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
745	745
746		-
747		-
748	748	=== 3.4.1 Common Commands ===
749	749
750	750	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
...	...	@@ -766,7 +766,6 @@
766	766
767	767	**Example: **AT+TDC=30000. Means set interval to 30 seconds
768	768
769		-
770	770	* Downlink Payload (prefix 0x01):
771	771
772	772	(% class="box infomessage" %)
...	...	@@ -789,7 +789,6 @@
789	789
790	790	**Example**: AT+MOD=2. Set work mode to Double DI counting mode
791	791
792		-
793	793	* Downlink Payload (prefix 0x0A):
794	794
795	795	(% class="box infomessage" %)
...	...	@@ -805,7 +805,6 @@
805	805
806	806	There is no AT Command to poll uplink
807	807
808		-
809	809	* Downlink Payload (prefix 0x08):
810	810
811	811	(% class="box infomessage" %)
...	...	@@ -832,7 +832,6 @@
832	832
833	833	0: Disable Trigger Mode
834	834
835		-
836	836	* Downlink Payload (prefix 0x0A 06):
837	837
838	838	(% class="box infomessage" %)
...	...	@@ -850,7 +850,6 @@
850	850
851	851	There is no AT Command for this feature.
852	852
853		-
854	854	* Downlink Payload (prefix 0x AB 06):
855	855
856	856	(% class="box infomessage" %)
...	...	@@ -871,7 +871,6 @@
871	871	**Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >**
872	872	)))
873	873
874		-
875	875	**Example:**
876	876
877	877	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
...	...	@@ -1111,7 +1111,7 @@
1111	1111
1112	1112
1113	1113
1114		-==== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ====
	1102	+=== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ===
1115	1115
1116	1116	* AT Command:
1117	1117