Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Last modified by Saxer Lin on 2025/04/15 17:24

From version < 77.73 >

edited by Xiaoling
on 2022/06/10 09:23

To version < 77.59 >

edited by Xiaoling
on 2022/06/10 09:11

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -666,7 +666,6 @@
  Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
--
  (% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
  MOD6 Payload : total 11 bytes payload
@@ -673,7 +673,6 @@
  [[image:image-20220524085923-1.png]]
--
  (% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if trigger is set for this part. Totally 1byte as below
  [[image:image-20220524090106-2.png]]
@@ -680,7 +680,6 @@
  * Each bits shows if the corresponding trigger has been configured.
--
  **Example:**
  10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
@@ -692,7 +692,6 @@
  * Each bits shows which status has been trigger on this uplink.
--
  **Example:**
  10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
@@ -743,8 +743,6 @@
  * (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
--
--
  === 3.4.1 Common Commands ===
  They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
@@ -766,7 +766,6 @@
  **Example: **AT+TDC=30000. Means set interval to 30 seconds
--
  * Downlink Payload (prefix 0x01):
  (% class="box infomessage" %)
@@ -789,7 +789,6 @@
  **Example**: AT+MOD=2. Set work mode to Double DI counting mode
--
  * Downlink Payload (prefix 0x0A):
  (% class="box infomessage" %)
@@ -805,7 +805,6 @@
  There is no AT Command to poll uplink
--
  * Downlink Payload (prefix 0x08):
  (% class="box infomessage" %)
@@ -832,7 +832,6 @@
 : Disable Trigger Mode
--
  * Downlink Payload (prefix 0x0A 06):
  (% class="box infomessage" %)
@@ -850,7 +850,6 @@
  There is no AT Command for this feature.
--
  * Downlink Payload (prefix 0x AB 06):
  (% class="box infomessage" %)
@@ -871,7 +871,6 @@
  **Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >**
  )))
--
  **Example:**
  AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
@@ -900,12 +900,10 @@
  b : delay timing.
--
  **Example:**
  AT+TRIG1=1,100(set DI1 port to trigger on high level, valid signal is 100ms )
--
  * Downlink Payload (prefix 0x09 01 ):
  (% class="box infomessage" %)
@@ -930,12 +930,10 @@
  b : delay timing.
--
  **Example:**
  AT+TRIG2=0,100(set DI1 port to trigger on low level, valid signal is 100ms )
--
  * Downlink Payload (prefix 0x09 02 ):
  (% class="box infomessage" %)
@@ -956,7 +956,6 @@
  **AT+ACLIM. **
  )))
--
  * Downlink Payload (prefix 0xAA 01 ):
  (% class="box infomessage" %)
@@ -977,7 +977,6 @@
  **AT+AVLIM. See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]**
  )))
--
  * Downlink Payload (prefix 0xAA 00 ):
  (% class="box infomessage" %)
@@ -998,7 +998,6 @@
  **AT+ATDC=5. Device won’t response the second trigger within 5 minute after the first trigger.**
  )))
--
  * Downlink Payload (prefix 0xAC ):
  (% class="box infomessage" %)
@@ -1014,7 +1014,6 @@
  There is no AT Command to control Digital Output
--
  * Downlink Payload (prefix 0x02):
  (% class="box infomessage" %)
@@ -1048,7 +1048,6 @@
  There is no AT Command to control Digital Output
--
  * Downlink Payload (prefix 0xA9):
  (% class="box infomessage" %)
@@ -1068,22 +1068,18 @@
 : DO pins will change to an inverter state after timeout
--
  (% style="color:#4f81bd" %)**Third Byte**(%%): Control Method and Ports status:
  [[image:image-20220524093238-6.png]]
--
  (% style="color:#4f81bd" %)**Fourth Byte**(%%): Control Method and Ports status:
  [[image:image-20220524093328-7.png]]
--
  (% style="color:#4f81bd" %)**Fifth Byte**(%%): Control Method and Ports status:
  [[image:image-20220524093351-8.png]]
--
  (% style="color:#4f81bd" %)**Sixth and Seventh Byte**:
           Latching time. Unit: ms
@@ -1090,7 +1090,6 @@
  Device will upload a packet if downlink code executes successfully.
--
  **Example payload:**
  **~1. A9 01 01 01 01 07 D0**
@@ -1111,13 +1111,12 @@
--==== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ====
++=== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ===
  * AT Command:
  There is no AT Command to control Relay Output
--
  * Downlink Payload (prefix 0x03):
  (% class="box infomessage" %)
@@ -1147,7 +1147,6 @@
  There is no AT Command to control Relay Output
--
  * Downlink Payload (prefix 0x05):
  (% class="box infomessage" %)
@@ -1165,17 +1165,14 @@
 : Relays will change to an inverter state after timeout
--
  (% style="color:#4f81bd" %)**Third Byte(bb)**(%%): Control Method and Ports status:
  [[image:image-20220524093831-10.png]]
--
  (% style="color:#4f81bd" %)**Fourth/Fifth Bytes(cc)**(%%): Latching time. Unit: ms
  Device will upload a packet if downlink code executes successfully.
--
  **Example payload:**
  **~1. 05 01 11 07 D0**
@@ -1207,7 +1207,6 @@
  **AT+VOLMAX    ~/~/ See [[MOD4>>||anchor="H3.3.4AT2BMOD3D42CSingleDICounting2B1xVoltageCounting"]]**
  )))
--
  * Downlink Payload (prefix 0xA5):
  (% class="box infomessage" %)
@@ -1234,7 +1234,6 @@
  Bb cc dd ee: number to be set
--
  * Downlink Payload (prefix 0xA8):
  (% class="box infomessage" %)
@@ -1287,16 +1287,17 @@
  )))
++
  == 3.5 Integrate with Mydevice ==
  Mydevices provides a human friendly interface to show the sensor data, once we have data in TTN, we can use Mydevices to connect to TTN and see the data in Mydevices. Below are the steps:
  (((
--(% style="color:blue" %)**Step 1**(%%): Be sure that your device is programmed and properly connected to the network at this time.
++**Step 1**: Be sure that your device is programmed and properly connected to the network at this time.
  )))
  (((
--(% style="color:blue" %)**Step 2**(%%): To configure the Application to forward data to Mydevices you will need to add integration. To add the Mydevices integration, perform the following steps:
++**Step 2**: To configure the Application to forward data to Mydevices you will need to add integration. To add the Mydevices integration, perform the following steps:
  )))
  [[image:1653356737703-362.png||height="232" width="732"]]
@@ -1303,13 +1303,12 @@
  [[image:image-20220524094641-11.png||height="390" width="723"]]
--
  [[image:image-20220524094641-12.png||height="402" width="718"]]
--(% style="color:blue" %)**Step 3**(%%): Create an account or log in Mydevices.
++**Step 3**: Create an account or log in Mydevices.
--(% style="color:blue" %)**Step 4**(%%): Search LT-22222-L(for both LT-22222-L / LT-33222-L) and add DevEUI.(% style="display:none" %)
++**Step 4**: Search LT-22222-L(for both LT-22222-L / LT-33222-L) and add DevEUI.(% style="display:none" %)
  Search under The things network

Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Summary

Details

Applications

Navigation