Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -602,11 +602,13 @@
602	602	* **AT+MOD=1 ** **~-~->** The normal working mode
603	603	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
604	604
	605	+
605	605	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
606	606
607	607	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
608	608	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
609	609
	611	+
610	610	**AT Command to set Trigger Condition**:
611	611
612	612	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -658,14 +658,17 @@
658	658
659	659	Yy4 yy4: AC2 or AV2 high limit.
660	660
	663	+
661	661	**Example1**: AA 00 13 88 00 00 00 00 00 00
662	662
663	663	Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
664	664
	668	+
665	665	**Example2**: AA 02 01 00
666	666
667	667	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
668	668
	673	+
669	669	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
670	670
671	671	MOD6 Payload : total 11 bytes payload
...	...	@@ -672,6 +672,7 @@
672	672
673	673	[[image:image-20220524085923-1.png]]
674	674
	680	+
675	675	(% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if trigger is set for this part. Totally 1byte as below
676	676
677	677	[[image:image-20220524090106-2.png]]
...	...	@@ -678,6 +678,7 @@
678	678
679	679	* Each bits shows if the corresponding trigger has been configured.
680	680
	687	+
681	681	**Example:**
682	682
683	683	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -689,6 +689,7 @@
689	689
690	690	* Each bits shows which status has been trigger on this uplink.
691	691
	699	+
692	692	**Example:**
693	693
694	694	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -700,6 +700,7 @@
700	700
701	701	* Each bits shows which status has been trigger on this uplink.
702	702
	711	+
703	703	**Example:**
704	704
705	705	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -740,6 +740,7 @@
740	740	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
741	741
742	742
	752	+
743	743	=== 3.4.1 Common Commands ===
744	744
745	745	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
...	...	@@ -1106,7 +1106,7 @@
1106	1106
1107	1107
1108	1108
1109		-=== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ===
	1119	+==== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ====
1110	1110
1111	1111	* AT Command:
1112	1112