Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -666,6 +666,7 @@
666	666
667	667	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
668	668
	669	+
669	669	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
670	670
671	671	MOD6 Payload : total 11 bytes payload
...	...	@@ -672,6 +672,7 @@
672	672
673	673	[[image:image-20220524085923-1.png]]
674	674
	676	+
675	675	(% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if trigger is set for this part. Totally 1byte as below
676	676
677	677	[[image:image-20220524090106-2.png]]
...	...	@@ -678,6 +678,7 @@
678	678
679	679	* Each bits shows if the corresponding trigger has been configured.
680	680
	683	+
681	681	**Example:**
682	682
683	683	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -689,6 +689,7 @@
689	689
690	690	* Each bits shows which status has been trigger on this uplink.
691	691
	695	+
692	692	**Example:**
693	693
694	694	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -739,6 +739,8 @@
739	739
740	740	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
741	741
	746	+
	747	+
742	742	=== 3.4.1 Common Commands ===
743	743
744	744	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
...	...	@@ -760,6 +760,7 @@
760	760
761	761	**Example: **AT+TDC=30000. Means set interval to 30 seconds
762	762
	769	+
763	763	* Downlink Payload (prefix 0x01):
764	764
765	765	(% class="box infomessage" %)
...	...	@@ -782,6 +782,7 @@
782	782
783	783	**Example**: AT+MOD=2. Set work mode to Double DI counting mode
784	784
	792	+
785	785	* Downlink Payload (prefix 0x0A):
786	786
787	787	(% class="box infomessage" %)
...	...	@@ -797,6 +797,7 @@
797	797
798	798	There is no AT Command to poll uplink
799	799
	808	+
800	800	* Downlink Payload (prefix 0x08):
801	801
802	802	(% class="box infomessage" %)
...	...	@@ -823,6 +823,7 @@
823	823
824	824	0: Disable Trigger Mode
825	825
	835	+
826	826	* Downlink Payload (prefix 0x0A 06):
827	827
828	828	(% class="box infomessage" %)
...	...	@@ -840,6 +840,7 @@
840	840
841	841	There is no AT Command for this feature.
842	842
	853	+
843	843	* Downlink Payload (prefix 0x AB 06):
844	844
845	845	(% class="box infomessage" %)
...	...	@@ -860,6 +860,7 @@
860	860	**Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >**
861	861	)))
862	862
	874	+
863	863	**Example:**
864	864
865	865	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
...	...	@@ -1099,7 +1099,7 @@
1099	1099
1100	1100
1101	1101
1102		-=== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ===
	1114	+==== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ====
1103	1103
1104	1104	* AT Command:
1105	1105