Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Last modified by Saxer Lin on 2025/04/15 17:24

From version < 77.65 >

edited by Xiaoling
on 2022/06/10 09:19

To version < 77.53 >

edited by Xiaoling
on 2022/06/10 09:06

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -888,12 +888,10 @@
  b : delay timing.
--
  **Example:**
  AT+TRIG1=1,100(set DI1 port to trigger on high level, valid signal is 100ms )
--
  * Downlink Payload (prefix 0x09 01 ):
  (% class="box infomessage" %)
@@ -918,12 +918,10 @@
  b : delay timing.
--
  **Example:**
  AT+TRIG2=0,100(set DI1 port to trigger on low level, valid signal is 100ms )
--
  * Downlink Payload (prefix 0x09 02 ):
  (% class="box infomessage" %)
@@ -944,7 +944,6 @@
  **AT+ACLIM. **
  )))
--
  * Downlink Payload (prefix 0xAA 01 ):
  (% class="box infomessage" %)
@@ -965,7 +965,6 @@
  **AT+AVLIM. See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]**
  )))
--
  * Downlink Payload (prefix 0xAA 00 ):
  (% class="box infomessage" %)
@@ -986,7 +986,6 @@
  **AT+ATDC=5. Device won’t response the second trigger within 5 minute after the first trigger.**
  )))
--
  * Downlink Payload (prefix 0xAC ):
  (% class="box infomessage" %)
@@ -1002,7 +1002,6 @@
  There is no AT Command to control Digital Output
--
  * Downlink Payload (prefix 0x02):
  (% class="box infomessage" %)
@@ -1036,7 +1036,6 @@
  There is no AT Command to control Digital Output
--
  * Downlink Payload (prefix 0xA9):
  (% class="box infomessage" %)
@@ -1056,22 +1056,18 @@
 : DO pins will change to an inverter state after timeout
--
  (% style="color:#4f81bd" %)**Third Byte**(%%): Control Method and Ports status:
  [[image:image-20220524093238-6.png]]
--
  (% style="color:#4f81bd" %)**Fourth Byte**(%%): Control Method and Ports status:
  [[image:image-20220524093328-7.png]]
--
  (% style="color:#4f81bd" %)**Fifth Byte**(%%): Control Method and Ports status:
  [[image:image-20220524093351-8.png]]
--
  (% style="color:#4f81bd" %)**Sixth and Seventh Byte**:
           Latching time. Unit: ms
@@ -1078,7 +1078,6 @@
  Device will upload a packet if downlink code executes successfully.
--
  **Example payload:**
  **~1. A9 01 01 01 01 07 D0**
@@ -1105,7 +1105,6 @@
  There is no AT Command to control Relay Output
--
  * Downlink Payload (prefix 0x03):
  (% class="box infomessage" %)
@@ -1135,7 +1135,6 @@
  There is no AT Command to control Relay Output
--
  * Downlink Payload (prefix 0x05):
  (% class="box infomessage" %)
@@ -1153,17 +1153,14 @@
 : Relays will change to an inverter state after timeout
--
  (% style="color:#4f81bd" %)**Third Byte(bb)**(%%): Control Method and Ports status:
  [[image:image-20220524093831-10.png]]
--
  (% style="color:#4f81bd" %)**Fourth/Fifth Bytes(cc)**(%%): Latching time. Unit: ms
  Device will upload a packet if downlink code executes successfully.
--
  **Example payload:**
  **~1. 05 01 11 07 D0**
@@ -1195,7 +1195,6 @@
  **AT+VOLMAX    ~/~/ See [[MOD4>>||anchor="H3.3.4AT2BMOD3D42CSingleDICounting2B1xVoltageCounting"]]**
  )))
--
  * Downlink Payload (prefix 0xA5):
  (% class="box infomessage" %)
@@ -1222,7 +1222,6 @@
  Bb cc dd ee: number to be set
--
  * Downlink Payload (prefix 0xA8):
  (% class="box infomessage" %)
@@ -1275,16 +1275,17 @@
  )))
++
  == 3.5 Integrate with Mydevice ==
  Mydevices provides a human friendly interface to show the sensor data, once we have data in TTN, we can use Mydevices to connect to TTN and see the data in Mydevices. Below are the steps:
  (((
--(% style="color:blue" %)**Step 1**(%%): Be sure that your device is programmed and properly connected to the network at this time.
++**Step 1**: Be sure that your device is programmed and properly connected to the network at this time.
  )))
  (((
--(% style="color:blue" %)**Step 2**(%%): To configure the Application to forward data to Mydevices you will need to add integration. To add the Mydevices integration, perform the following steps:
++**Step 2**: To configure the Application to forward data to Mydevices you will need to add integration. To add the Mydevices integration, perform the following steps:
  )))
  [[image:1653356737703-362.png||height="232" width="732"]]
@@ -1291,13 +1291,12 @@
  [[image:image-20220524094641-11.png||height="390" width="723"]]
--
  [[image:image-20220524094641-12.png||height="402" width="718"]]
--(% style="color:blue" %)**Step 3**(%%): Create an account or log in Mydevices.
++**Step 3**: Create an account or log in Mydevices.
--(% style="color:blue" %)**Step 4**(%%): Search LT-22222-L(for both LT-22222-L / LT-33222-L) and add DevEUI.(% style="display:none" %)
++**Step 4**: Search LT-22222-L(for both LT-22222-L / LT-33222-L) and add DevEUI.(% style="display:none" %)
  Search under The things network
@@ -1304,21 +1304,16 @@
  [[image:1653356838789-523.png||height="337" width="740"]]
--
  After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
  [[image:image-20220524094909-1.png||height="335" width="729"]]
--
  [[image:image-20220524094909-2.png||height="337" width="729"]]
--
  [[image:image-20220524094909-3.png||height="338" width="727"]]
--
  [[image:image-20220524094909-4.png||height="339" width="728"]](% style="display:none" %)
--
  [[image:image-20220524094909-5.png||height="341" width="734"]]
@@ -1358,7 +1358,7 @@
  )))
  (((
--(% style="color:blue" %)**Example1**(%%): Connect to a Low active sensor.
++**Example1**: Connect to a Low active sensor.
  )))
  (((
@@ -1389,7 +1389,7 @@
  )))
  (((
--(% style="color:blue" %)**Example2**(%%): Connect to a High active sensor.
++**Example2**: Connect to a High active sensor.
  )))
  (((
@@ -1420,7 +1420,7 @@
  )))
  (((
--(% style="color:blue" %)**Example3**(%%): Connect to a 220v high active sensor.
++**Example3**: Connect to a 220v high active sensor.
  )))
  (((
@@ -1460,9 +1460,8 @@
  The analog input interface is as below. The LT will measure the IN2 voltage so to calculate the current pass the Load. The formula is:
++**AC2 = (IN2 voltage )/12**
--(% style="color:blue" %)**AC2 = (IN2 voltage )/12**
--
  [[image:1653357592296-182.png]]
  Example to connect a 4~~20mA sensor
@@ -1469,18 +1469,17 @@
  We take the wind speed sensor as an example for reference only.
++Specifications of the wind speed sensor:
--**Specifications of the wind speed sensor:**
++Red:12~~24v
--Red:      12~~24v
++Yellow:4~~20mA
--Yellow:  4~~20mA
++Black:GND
--Black:   GND
++Connection diagram:
--**Connection diagram:**
--
  [[image:1653357640609-758.png]]
  [[image:1653357648330-671.png||height="155" width="733"]]
@@ -1512,7 +1512,6 @@
  [[image:1653358238933-385.png]]
--
  (((
  In PC, User needs to set (% style="color:#4f81bd" %)**serial tool**(%%)(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to (% style="color:green" %)**9600**(%%) to access to access serial console for LT. The AT commands are disable by default and need to enter password (default:(% style="color:green" %)**123456**)(%%) to active it. As shown below:
  )))
@@ -2019,6 +2019,7 @@
  * (% style="color:#4f81bd" %)**IN865**(%%): LT with frequency bands IN865
  * (% style="color:#4f81bd" %)**CN779**(%%): LT with frequency bands CN779
++
  = 8. Packing Info =
@@ -2036,6 +2036,7 @@
  * Package Size / pcs : 14.5 x 8 x 5 cm
  * Weight / pcs : 170g
++
  = 9. Support =
  * (((
@@ -2045,6 +2045,7 @@
  Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]
  )))
++
  = 10. Reference =
  * LT-22222-L: [[http:~~/~~/www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html]]

Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Summary

Details

Applications

Navigation