Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -888,10 +888,12 @@
888	888
889	889	b : delay timing.
890	890
	891	+
891	891	**Example:**
892	892
893	893	AT+TRIG1=1,100(set DI1 port to trigger on high level, valid signal is 100ms )
894	894
	896	+
895	895	* Downlink Payload (prefix 0x09 01 ):
896	896
897	897	(% class="box infomessage" %)
...	...	@@ -916,10 +916,12 @@
916	916
917	917	b : delay timing.
918	918
	921	+
919	919	**Example:**
920	920
921	921	AT+TRIG2=0,100(set DI1 port to trigger on low level, valid signal is 100ms )
922	922
	926	+
923	923	* Downlink Payload (prefix 0x09 02 ):
924	924
925	925	(% class="box infomessage" %)
...	...	@@ -940,6 +940,7 @@
940	940	**AT+ACLIM. **
941	941	)))
942	942
	947	+
943	943	* Downlink Payload (prefix 0xAA 01 ):
944	944
945	945	(% class="box infomessage" %)
...	...	@@ -960,6 +960,7 @@
960	960	**AT+AVLIM. See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]**
961	961	)))
962	962
	968	+
963	963	* Downlink Payload (prefix 0xAA 00 ):
964	964
965	965	(% class="box infomessage" %)
...	...	@@ -980,6 +980,7 @@
980	980	**AT+ATDC=5. Device won’t response the second trigger within 5 minute after the first trigger.**
981	981	)))
982	982
	989	+
983	983	* Downlink Payload (prefix 0xAC ):
984	984
985	985	(% class="box infomessage" %)
...	...	@@ -995,6 +995,7 @@
995	995
996	996	There is no AT Command to control Digital Output
997	997
	1005	+
998	998	* Downlink Payload (prefix 0x02):
999	999
1000	1000	(% class="box infomessage" %)
...	...	@@ -1028,6 +1028,7 @@
1028	1028
1029	1029	There is no AT Command to control Digital Output
1030	1030
	1039	+
1031	1031	* Downlink Payload (prefix 0xA9):
1032	1032
1033	1033	(% class="box infomessage" %)
...	...	@@ -1047,18 +1047,22 @@
1047	1047
1048	1048	00: DO pins will change to an inverter state after timeout
1049	1049
	1059	+
1050	1050	(% style="color:#4f81bd" %)**Third Byte**(%%): Control Method and Ports status:
1051	1051
1052	1052	[[image:image-20220524093238-6.png]]
1053	1053
	1064	+
1054	1054	(% style="color:#4f81bd" %)**Fourth Byte**(%%): Control Method and Ports status:
1055	1055
1056	1056	[[image:image-20220524093328-7.png]]
1057	1057
	1069	+
1058	1058	(% style="color:#4f81bd" %)**Fifth Byte**(%%): Control Method and Ports status:
1059	1059
1060	1060	[[image:image-20220524093351-8.png]]
1061	1061
	1074	+
1062	1062	(% style="color:#4f81bd" %)**Sixth and Seventh Byte**:
1063	1063
1064	1064	Latching time. Unit: ms
...	...	@@ -1065,6 +1065,7 @@
1065	1065
1066	1066	Device will upload a packet if downlink code executes successfully.
1067	1067
	1081	+
1068	1068	**Example payload:**
1069	1069
1070	1070	**~1. A9 01 01 01 01 07 D0**
...	...	@@ -1091,6 +1091,7 @@
1091	1091
1092	1092	There is no AT Command to control Relay Output
1093	1093
	1108	+
1094	1094	* Downlink Payload (prefix 0x03):
1095	1095
1096	1096	(% class="box infomessage" %)