Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -76,6 +76,8 @@
76	76	)))
77	77
78	78	(((
	79	+
	80	+
79	79	**Interface for Model: LT22222-L:**
80	80	)))
81	81
...	...	@@ -99,6 +99,8 @@
99	99	)))
100	100
101	101	(((
	104	+
	105	+
102	102	**LoRa Spec:**
103	103	)))
104	104
...	...	@@ -158,8 +158,6 @@
158	158	)))
159	159	* (((
160	160	Packet engine up to 256 bytes with CRC.
161		-
162		-
163	163	)))
164	164
165	165	== 1.3 Features ==
...	...	@@ -216,8 +216,6 @@
216	216
217	217	(((
218	218	In case user can’t set the OTAA keys in the network server and has to use the existing keys from server. User can [[use AT Command>>||anchor="H4.UseATCommand"]] to set the keys in the devices.
219		-
220		-
221	221	)))
222	222
223	223
...	...	@@ -277,7 +277,6 @@
277	277	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
278	278
279	279
280		-
281	281	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
282	282
283	283	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -317,6 +317,7 @@
317	317	* [0] RO2 relay channel is open and RO2 LED is OFF;
318	318
319	319
	319	+
320	320	**LT22222-L:**
321	321
322	322	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -333,7 +333,6 @@
333	333	** DO1 LED is off in both case
334	334
335	335
336		-
337	337	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
338	338
339	339
...	...	@@ -474,11 +474,10 @@
474	474
475	475	(((
476	476	Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
477		-
478		-
479	479	)))
480	480
481	481
	479	+
482	482	=== 3.3.4 AT+MOD~=4, Single DI Counting + 1 x Voltage Counting ===
483	483
484	484
...	...	@@ -631,7 +631,6 @@
631	631	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
632	632	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
633	633
634		-
635	635	**AT Command to set Trigger Condition**:
636	636
637	637	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -711,7 +711,6 @@
711	711
712	712	* Each bits shows if the corresponding trigger has been configured.
713	713
714		-
715	715	**Example:**
716	716
717	717	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -723,7 +723,6 @@
723	723
724	724	* Each bits shows which status has been trigger on this uplink.
725	725
726		-
727	727	**Example:**
728	728
729	729	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -735,7 +735,6 @@
735	735
736	736	* Each bits shows which status has been trigger on this uplink.
737	737
738		-
739	739	**Example:**
740	740
741	741	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -764,7 +764,6 @@
764	764	)))
765	765
766	766
767		-
768	768	== 3.4 ​Configure LT via AT or Downlink ==
769	769
770	770	User can configure LT I/O Controller via AT Commands or LoRaWAN Downlink Commands
...	...	@@ -777,7 +777,6 @@
777	777
778	778	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
779	779
780		-
781	781	=== 3.4.1 Common Commands ===
782	782
783	783	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]