Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -235,7 +235,7 @@
235	235	)))
236	236
237	237	(((
238		-**(% style="color:blue" %)Step 1**(%%): Create a device in TTN with the OTAA keys from LT IO controller.
	238	+(% style="color:blue" %)**Step 1**(%%): Create a device in TTN with the OTAA keys from LT IO controller.
239	239	)))
240	240
241	241	(((
...	...	@@ -244,6 +244,7 @@
244	244
245	245	[[image:1653297924498-393.png]]
246	246
	247	+
247	247	Input these keys in the LoRaWAN Server portal. Below is TTN screen shot:
248	248
249	249	Add APP EUI in the application.
...	...	@@ -257,7 +257,7 @@
257	257
258	258
259	259	(((
260		-**(% style="color:blue" %)Step 2**(%%): Power on LT and it will auto join to the TTN network. After join success, it will start to upload message to TTN and user can see in the panel.
	261	+(% style="color:blue" %)**Step 2**(%%): Power on LT and it will auto join to the TTN network. After join success, it will start to upload message to TTN and user can see in the panel.
261	261	)))
262	262
263	263	[[image:1653298044601-602.png||height="405" width="709"]]
...	...	@@ -276,7 +276,6 @@
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
278	278
279		-
280	280	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
281	281
282	282	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -316,7 +316,6 @@
316	316	* [0] RO2 relay channel is open and RO2 LED is OFF;
317	317
318	318
319		-
320	320	**LT22222-L:**
321	321
322	322	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -333,7 +333,6 @@
333	333	** DO1 LED is off in both case
334	334
335	335
336		-
337	337	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
338	338
339	339
...	...	@@ -626,7 +626,6 @@
626	626	* **AT+MOD=1 ** **~-~->** The normal working mode
627	627	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
628	628
629		-
630	630	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
631	631
632	632	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
...	...	@@ -633,7 +633,6 @@
633	633	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
634	634
635	635
636		-
637	637	**AT Command to set Trigger Condition**:
638	638
639	639	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -714,7 +714,6 @@
714	714	* Each bits shows if the corresponding trigger has been configured.
715	715
716	716
717		-
718	718	**Example:**
719	719
720	720	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -727,7 +727,6 @@
727	727	* Each bits shows which status has been trigger on this uplink.
728	728
729	729
730		-
731	731	**Example:**
732	732
733	733	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -740,7 +740,6 @@
740	740	* Each bits shows which status has been trigger on this uplink.
741	741
742	742
743		-
744	744	**Example:**
745	745
746	746	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -783,7 +783,6 @@
783	783	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
784	784
785	785
786		-
787	787	=== 3.4.1 Common Commands ===
788	788
789	789	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]