Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -322,6 +322,7 @@
322	322	* [1] RO1 relay channel is close and the RO1 LED is ON.
323	323	* [0] RO2 relay channel is open and RO2 LED is OFF;
324	324
	325	+
325	325	**LT22222-L:**
326	326
327	327	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -337,6 +337,8 @@
337	337	** DO1 is high in case there is load between DO1 and V+.
338	338	** DO1 LED is off in both case
339	339
	341	+
	342	+
340	340	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
341	341
342	342	**For LT-22222-L**: this mode the **DI1 and DI2** are used as counting pins.
...	...	@@ -430,6 +430,7 @@
430	430	)))
431	431
432	432
	436	+
433	433	=== 3.3.3 AT+MOD~=3, Single DI Counting + 2 x ACI ===
434	434
435	435	**LT22222-L**: This mode the DI1 is used as a counting pin.
...	...	@@ -474,6 +474,8 @@
474	474
475	475	)))
476	476
	481	+
	482	+
477	477	=== 3.3.4 AT+MOD~=4, Single DI Counting + 1 x Voltage Counting ===
478	478
479	479	**LT22222-L**: This mode the DI1 is used as a counting pin.
...	...	@@ -555,6 +555,7 @@
555	555	)))
556	556
557	557
	564	+
558	558	=== 3.3.5 AT+MOD~=5, Single DI Counting + 2 x AVI + 1 x ACI ===
559	559
560	560	**LT22222-L**: This mode the DI1 is used as a counting pin.
...	...	@@ -599,6 +599,8 @@
599	599
600	600	)))
601	601
	609	+
	610	+
602	602	=== 3.3.6 AT+ADDMOD~=6. (Trigger Mode, Optional) ===
603	603
604	604	(% style="color:#4f81bd" %)**This mode is an optional mode for trigger purpose. It can run together with other mode.**
...	...	@@ -722,6 +722,7 @@
722	722	When device got this command, it will send the MOD6 payload.
723	723
724	724
	734	+
725	725	=== 3.3.7 Payload Decoder ===
726	726
727	727	(((
...	...	@@ -730,6 +730,8 @@
730	730
731	731	)))
732	732
	743	+
	744	+
733	733	== 3.4 ​Configure LT via AT or Downlink ==
734	734
735	735	User can configure LT I/O Controller via AT Commands or LoRaWAN Downlink Commands
...	...	@@ -742,11 +742,14 @@
742	742
743	743	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
744	744
	757	+
	758	+
745	745	=== 3.4.1 Common Commands ===
746	746
747	747	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
748	748
749	749
	764	+
750	750	=== 3.4.2 Sensor related commands ===
751	751
752	752	==== 3.4.2.1 Set Transmit Interval ====
...	...	@@ -770,6 +770,7 @@
770	770	)))
771	771
772	772
	788	+
773	773	==== 3.4.2.2 Set Work Mode (AT+MOD) ====
774	774
775	775	Set work mode.
...	...	@@ -791,6 +791,7 @@
791	791	)))
792	792
793	793
	810	+
794	794	==== 3.4.2.3 Poll an uplink ====
795	795
796	796	* AT Command: