Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -193,6 +193,8 @@
193	193	* 1 x Counting Port
194	194	)))
195	195
	196	+
	197	+
196	196	= 2. Power ON Device =
197	197
198	198	The LT controller can be powered by 7 ~~ 24V DC power source. Connect VIN to Power Input V+ and GND to power input V- to power the LT controller.
...	...	@@ -270,6 +270,8 @@
270	270	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
271	271	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
272	272
	275	+
	276	+
273	273	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
274	274
275	275	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -320,6 +320,8 @@
320	320	** DO1 is high in case there is load between DO1 and V+.
321	321	** DO1 LED is off in both case
322	322
	327	+
	328	+
323	323	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
324	324
325	325	**For LT-22222-L**: this mode the **DI1 and DI2** are used as counting pins.
...	...	@@ -608,6 +608,7 @@
608	608
609	609	AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
610	610
	617	+
611	611	(% style="color:#4f81bd" %)**Trigger base on current**:
612	612
613	613	Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
...	...	@@ -616,6 +616,7 @@
616	616
617	617	AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
618	618
	626	+
619	619	(% style="color:#4f81bd" %)**Trigger base on DI status**:
620	620
621	621	DI status trigger Flag.
...	...	@@ -719,7 +719,7 @@
719	719	There are two kinds of Commands:
720	720	)))
721	721
722		-* (% style="color:#4f81bd" %)**Common Commands**(%%): They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands
	730	+* (% style="color:#4f81bd" %)**Common Commands**(%%): They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
723	723
724	724	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
725	725
...	...	@@ -790,7 +790,7 @@
790	790
791	791	==== 3.4.2.4 Enable Trigger Mode ====
792	792
793		-Use of trigger mode, please check [[ADDMOD6>>path:http://8.211.40.43:8080/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/#H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29]]
	801	+Use of trigger mode, please check [[ADDMOD6>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
794	794
795	795	* AT Command:
796	796
...	...	@@ -906,7 +906,7 @@
906	906
907	907	==== 3.4.2.9 Trigger – Set AC (current) as trigger ====
908	908
909		-Set current trigger , base on AC port. See [[trigger mode>>path:http://8.211.40.43:8080/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/#H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29]]
	917	+Set current trigger , base on AC port. See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
910	910
911	911	* AT Command:
912	912