Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -178,6 +178,8 @@
178	178	* Smart Cities
179	179	* Smart Factory
180	180
	181	+
	182	+
181	181	== 1.5 Hardware Variants ==
182	182
183	183	(% border="1" style="background-color:#f7faff; width:500px" %)
...	...	@@ -191,6 +191,8 @@
191	191	* 1 x Counting Port
192	192	)))
193	193
	196	+
	197	+
194	194	= 2. Power ON Device =
195	195
196	196	The LT controller can be powered by 7 ~~ 24V DC power source. Connect VIN to Power Input V+ and GND to power input V- to power the LT controller.
...	...	@@ -268,6 +268,8 @@
268	268	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
269	269	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
270	270
	275	+
	276	+
271	271	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
272	272
273	273	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -318,6 +318,8 @@
318	318	** DO1 is high in case there is load between DO1 and V+.
319	319	** DO1 LED is off in both case
320	320
	327	+
	328	+
321	321	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
322	322
323	323	**For LT-22222-L**: this mode the **DI1 and DI2** are used as counting pins.
...	...	@@ -606,6 +606,7 @@
606	606
607	607	AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
608	608
	617	+
609	609	(% style="color:#4f81bd" %)**Trigger base on current**:
610	610
611	611	Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
...	...	@@ -614,6 +614,7 @@
614	614
615	615	AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
616	616
	626	+
617	617	(% style="color:#4f81bd" %)**Trigger base on DI status**:
618	618
619	619	DI status trigger Flag.
...	...	@@ -717,7 +717,7 @@
717	717	There are two kinds of Commands:
718	718	)))
719	719
720		-* (% style="color:#4f81bd" %)**Common Commands**(%%): They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands
	730	+* (% style="color:#4f81bd" %)**Common Commands**(%%): They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
721	721
722	722	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
723	723