Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -193,8 +193,6 @@
193	193	* 1 x Counting Port
194	194	)))
195	195
196		-
197		-
198	198	= 2. Power ON Device =
199	199
200	200	The LT controller can be powered by 7 ~~ 24V DC power source. Connect VIN to Power Input V+ and GND to power input V- to power the LT controller.
...	...	@@ -272,8 +272,6 @@
272	272	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
273	273	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
274	274
275		-
276		-
277	277	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
278	278
279	279	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -324,8 +324,6 @@
324	324	** DO1 is high in case there is load between DO1 and V+.
325	325	** DO1 LED is off in both case
326	326
327		-
328		-
329	329	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
330	330
331	331	**For LT-22222-L**: this mode the **DI1 and DI2** are used as counting pins.
...	...	@@ -614,7 +614,6 @@
614	614
615	615	AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
616	616
617		-
618	618	(% style="color:#4f81bd" %)**Trigger base on current**:
619	619
620	620	Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
...	...	@@ -623,7 +623,6 @@
623	623
624	624	AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
625	625
626		-
627	627	(% style="color:#4f81bd" %)**Trigger base on DI status**:
628	628
629	629	DI status trigger Flag.
...	...	@@ -727,7 +727,7 @@
727	727	There are two kinds of Commands:
728	728	)))
729	729
730		-* (% style="color:#4f81bd" %)**Common Commands**(%%): They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
	722	+* (% style="color:#4f81bd" %)**Common Commands**(%%): They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands
731	731
732	732	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
733	733