Skip to Content
Last modified by Mengting Qiu on 2025/06/04 18:42
From version 75.10
edited by Xiaoling
on 2022/06/01 17:29
Change comment: There is no comment for this version
To version 75.14
edited by Xiaoling
on 2022/06/01 17:38
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -324,6 +324,8 @@
324 324  ** DO1 is high in case there is load between DO1 and V+.
325 325  ** DO1 LED is off in both case
326 326  
327 +
328 +
327 327  === 3.3.2 AT+MOD~=2, (Double DI Counting) ===
328 328  
329 329  **For LT-22222-L**: this mode the **DI1 and DI2** are used as counting pins.
... ... @@ -612,6 +612,7 @@
612 612  
613 613  AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
614 614  
617 +
615 615  (% style="color:#4f81bd" %)**Trigger base on current**:
616 616  
617 617  Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
... ... @@ -620,6 +620,7 @@
620 620  
621 621  AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
622 622  
626 +
623 623  (% style="color:#4f81bd" %)**Trigger base on DI status**:
624 624  
625 625  DI status trigger Flag.
... ... @@ -723,7 +723,7 @@
723 723  There are two kinds of Commands:
724 724  )))
725 725  
726 -* (% style="color:#4f81bd" %)**Common Commands**(%%): They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands
730 +* (% style="color:#4f81bd" %)**Common Commands**(%%): They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
727 727  
728 728  * (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
729 729  
... ... @@ -794,7 +794,7 @@
794 794  
795 795  ==== 3.4.2.4 Enable Trigger Mode ====
796 796  
797 -Use of trigger mode, please check [[ADDMOD6>>path:http://8.211.40.43:8080/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/#H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29]]
801 +Use of trigger mode, please check [[ADDMOD6>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
798 798  
799 799  * AT Command:
800 800  
... ... @@ -910,7 +910,7 @@
910 910  
911 911  ==== 3.4.2.9 Trigger – Set AC (current) as trigger ====
912 912  
913 -Set current trigger , base on AC port. See [[trigger mode>>path:http://8.211.40.43:8080/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/#H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29]]
917 +Set current trigger , base on AC port. See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
914 914  
915 915  * AT Command:
916 916