Last modified by Saxer Lin on 2025/04/15 17:24
<
From version < 66.25 >
edited by Xiaoling
on 2022/05/24 14:02
To version < 61.1 >
edited by Xiaoling
on 2022/05/24 10:34
>
Change comment: Uploaded new attachment "image-20220524103429-13.png", version {1}

Summary

Details

Page properties
Content
... ... @@ -45,114 +45,44 @@
45 45  
46 46  == 1.2  Specifications ==
47 47  
48 -(((
49 49  **Hardware System:**
50 -)))
51 51  
52 -* (((
53 -STM32L072CZT6 MCU
54 -)))
55 -* (((
56 -SX1276/78 Wireless Chip 
57 -)))
58 -* (((
59 -(((
60 -Power Consumption:
61 -)))
50 +* STM32L072CZT6 MCU
51 +* SX1276/78 Wireless Chip 
52 +* Power Consumption:
53 +** Idle: 4mA@12v
54 +** 20dB Transmit: 34mA@12v
62 62  
63 -* (((
64 -Idle: 4mA@12v
65 -)))
66 -* (((
67 -20dB Transmit: 34mA@12v
68 -)))
69 -)))
70 -
71 -(((
72 72  **Interface for Model: LT22222-L:**
73 -)))
74 74  
75 -* (((
76 -2 x Digital dual direction Input (Detect High/Low signal, Max: 50v, or 220v with optional external resistor)
77 -)))
78 -* (((
79 -2 x Digital Output (NPN output. Max pull up voltage 36V,450mA)
80 -)))
81 -* (((
82 -2 x Relay Output (5A@250VAC / 30VDC)
83 -)))
84 -* (((
85 -2 x 0~~20mA Analog Input (res:0.01mA)
86 -)))
87 -* (((
88 -2 x 0~~30V Analog Input (res:0.01v)
89 -)))
90 -* (((
91 -Power Input 7~~ 24V DC. 
92 -)))
58 +* 2 x Digital dual direction Input (Detect High/Low signal, Max: 50v, or 220v with optional external resistor)
59 +* 2 x Digital Output (NPN output. Max pull up voltage 36V,450mA)
60 +* 2 x Relay Output (5A@250VAC / 30VDC)
61 +* 2 x 0~~20mA Analog Input (res:0.01mA)
62 +* 2 x 0~~30V Analog Input (res:0.01v)
63 +* Power Input 7~~ 24V DC. 
93 93  
94 -(((
95 95  **LoRa Spec:**
96 -)))
97 97  
98 -* (((
99 -(((
100 -Frequency Range:
101 -)))
67 +* Frequency Range:
68 +** Band 1 (HF): 862 ~~ 1020 Mhz
69 +** Band 2 (LF): 410 ~~ 528 Mhz
70 +* 168 dB maximum link budget.
71 +* +20 dBm - 100 mW constant RF output vs.
72 +* +14 dBm high efficiency PA.
73 +* Programmable bit rate up to 300 kbps.
74 +* High sensitivity: down to -148 dBm.
75 +* Bullet-proof front end: IIP3 = -12.5 dBm.
76 +* Excellent blocking immunity.
77 +* Low RX current of 10.3 mA, 200 nA register retention.
78 +* Fully integrated synthesizer with a resolution of 61 Hz.
79 +* FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.
80 +* Built-in bit synchronizer for clock recovery.
81 +* Preamble detection.
82 +* 127 dB Dynamic Range RSSI.
83 +* Automatic RF Sense and CAD with ultra-fast AFC.
84 +* Packet engine up to 256 bytes with CRC.
102 102  
103 -* (((
104 -Band 1 (HF): 862 ~~ 1020 Mhz
105 -)))
106 -* (((
107 -Band 2 (LF): 410 ~~ 528 Mhz
108 -)))
109 -)))
110 -* (((
111 -168 dB maximum link budget.
112 -)))
113 -* (((
114 -+20 dBm - 100 mW constant RF output vs.
115 -)))
116 -* (((
117 -+14 dBm high efficiency PA.
118 -)))
119 -* (((
120 -Programmable bit rate up to 300 kbps.
121 -)))
122 -* (((
123 -High sensitivity: down to -148 dBm.
124 -)))
125 -* (((
126 -Bullet-proof front end: IIP3 = -12.5 dBm.
127 -)))
128 -* (((
129 -Excellent blocking immunity.
130 -)))
131 -* (((
132 -Low RX current of 10.3 mA, 200 nA register retention.
133 -)))
134 -* (((
135 -Fully integrated synthesizer with a resolution of 61 Hz.
136 -)))
137 -* (((
138 -FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.
139 -)))
140 -* (((
141 -Built-in bit synchronizer for clock recovery.
142 -)))
143 -* (((
144 -Preamble detection.
145 -)))
146 -* (((
147 -127 dB Dynamic Range RSSI.
148 -)))
149 -* (((
150 -Automatic RF Sense and CAD with ultra-fast AFC.
151 -)))
152 -* (((
153 -Packet engine up to 256 bytes with CRC.
154 -)))
155 -
156 156  == 1.3 Features ==
157 157  
158 158  * LoRaWAN Class A & Class C protocol
... ... @@ -199,21 +199,13 @@
199 199  
200 200  == 3.1 How it works? ==
201 201  
202 -(((
203 203  The LT is configured as LoRaWAN OTAA Class C mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the LT. It will auto join the network via OTAA. For LT-22222-L, the LED will show the Join status: After power on **TX LED** will fast blink 5 times, LT-22222-L will enter working mode and start to JOIN LoRaWAN network. **TX LED** will be on for 5 seconds after joined in network. When there is message from server, the **RX LED** will be on for 1 second. 
204 -)))
205 205  
206 -(((
207 -In case user can’t set the OTAA keys in the network server and has to use the existing keys from server. User can [[use AT Command>>path:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/#H4.UseATCommand]] to set the keys in the devices.
208 -)))
134 +In case user can’t set the OTAA keys in the network server and has to use the existing keys from server. User can [[use AT Command>>path:#AT_Command]] to set the keys in the devices.
209 209  
210 -(((
211 211  3.2 Example to join LoRaWAN network
212 -)))
213 213  
214 -(((
215 215  This chapter shows an example for how to join the TTN LoRaWAN Network. Below is the network structure, we use our LG308 as LoRaWAN gateway here. 
216 -)))
217 217  
218 218  [[image:image-20220523172350-1.png||height="266" width="864"]]
219 219  
... ... @@ -313,9 +313,7 @@
313 313  
314 314  **For LT-22222-L**: this mode the **DI1 and DI2** are used as counting pins.
315 315  
316 -(((
317 317  Total : 11 bytes payload
318 -)))
319 319  
320 320  [[image:image-20220523180452-3.png]]
321 321  
... ... @@ -329,77 +329,53 @@
329 329  * FIRST: Indicate this is the first packet after join network.
330 330  * DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
331 331  
332 -(((
333 333  (% style="color:red" %)Note: DO3 bit is not valid for LT-22222-L.
334 -)))
335 335  
336 -(((
337 337  **To use counting mode, please run:**
338 -)))
339 339  
340 340  (% class="box infomessage" %)
341 341  (((
342 -(((
343 343  **AT+MOD=2**
344 344  )))
345 -)))
346 346  
347 347  (% class="box infomessage" %)
348 348  (((
349 -(((
350 350  **ATZ**
351 351  )))
352 -)))
353 353  
354 -(((
355 355  (% style="color:#4f81bd" %)**AT Commands for counting:**
356 -)))
357 357  
358 -(((
359 359  **For LT22222-L:**
360 -)))
361 361  
362 362  (% class="box infomessage" %)
363 363  (((
364 -(((
365 365  **AT+TRIG1=0,100 (set DI1 port to trigger on low level, valid signal is 100ms) **
366 366  )))
367 -)))
368 368  
369 369  (% class="box infomessage" %)
370 370  (((
371 -(((
372 372  **AT+TRIG1=1,100(set DI1 port to trigger on high level, valid signal is 100ms ) **
373 373  )))
374 -)))
375 375  
376 376  (% class="box infomessage" %)
377 377  (((
378 -(((
379 379  **AT+TRIG2=0,100 (set DI2 port to trigger on low level, valid signal is 100ms) **
380 380  )))
381 -)))
382 382  
383 383  (% class="box infomessage" %)
384 384  (((
385 -(((
386 386  **AT+TRIG2=1,100 (set DI2 port to trigger on high level, valid signal is 100ms ) **
387 387  )))
388 -)))
389 389  
390 390  (% class="box infomessage" %)
391 391  (((
392 -(((
393 393  **AT+SETCNT=1,60   (Set COUNT1 value to 60)**
394 394  )))
395 -)))
396 396  
397 397  (% class="box infomessage" %)
398 398  (((
399 -(((
400 400  **AT+SETCNT=2,60   (Set COUNT2 value to 60)**
401 401  )))
402 -)))
403 403  
404 404  === 3.3.3 AT+MOD~=3, Single DI Counting + 2 x ACI ===
405 405  
... ... @@ -417,31 +417,21 @@
417 417  * FIRST: Indicate this is the first packet after join network.
418 418  * DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
419 419  
420 -(((
421 421  (% style="color:red" %)Note: DO3 is not valid for LT-22222-L.
422 -)))
423 423  
424 -(((
425 425  **To use counting mode, please run:**
426 -)))
427 427  
428 428  (% class="box infomessage" %)
429 429  (((
430 -(((
431 431  **AT+MOD=3**
432 432  )))
433 -)))
434 434  
435 435  (% class="box infomessage" %)
436 436  (((
437 -(((
438 438  **ATZ**
439 439  )))
440 -)))
441 441  
442 -(((
443 -Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/#H3.3.2AT2BMOD3D22C28DoubleDICounting29]].
444 -)))
330 +Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:#COUNT_COMMAND]].
445 445  
446 446  === 3.3.4 AT+MOD~=4, Single DI Counting + 1 x Voltage Counting ===
447 447  
... ... @@ -461,67 +461,44 @@
461 461  * FIRST: Indicate this is the first packet after join network.
462 462  * DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
463 463  
464 -(((
465 465  (% style="color:red" %)Note: DO3 is not valid for LT-22222-L.
466 -)))
467 467  
468 -(((
469 469  **To use this mode, please run:**
470 -)))
471 471  
472 472  (% class="box infomessage" %)
473 473  (((
474 -(((
475 475  **AT+MOD=4**
476 476  )))
477 -)))
478 478  
479 479  (% class="box infomessage" %)
480 480  (((
481 -(((
482 482  **ATZ**
483 483  )))
484 -)))
485 485  
486 -(((
487 -
488 -)))
489 489  
490 -(((
491 -Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/#H3.3.2AT2BMOD3D22C28DoubleDICounting29]].
492 -)))
365 +Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:#COUNT_COMMAND]].
493 493  
494 -(((
495 495  **Plus below command for AVI1 Counting:**
496 -)))
497 497  
498 498  (% class="box infomessage" %)
499 499  (((
500 -(((
501 501  **AT+SETCNT=3,60   (set AVI Count to 60)**
502 502  )))
503 -)))
504 504  
505 505  (% class="box infomessage" %)
506 506  (((
507 -(((
508 508  **AT+VOLMAX=20000   (If AVI1 voltage higher than VOLMAX (20000mV =20v), counter increase 1)**
509 509  )))
510 -)))
511 511  
512 512  (% class="box infomessage" %)
513 513  (((
514 -(((
515 515  **AT+VOLMAX=20000,0   (If AVI1 voltage lower than VOLMAX (20000mV =20v), counter increase 1)**
516 516  )))
517 -)))
518 518  
519 519  (% class="box infomessage" %)
520 520  (((
521 -(((
522 522  **AT+VOLMAX=20000,1   (If AVI1 voltage higer than VOLMAX (20000mV =20v), counter increase 1)**
523 523  )))
524 -)))
525 525  
526 526  === 3.3.5 AT+MOD~=5, Single DI Counting + 2 x AVI + 1 x ACI ===
527 527  
... ... @@ -535,35 +535,23 @@
535 535  
536 536  * RO is for relay. ROx=1 : close，ROx=0 always open.
537 537  * FIRST: Indicate this is the first packet after join network.
538 -* (((
539 -DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
540 -)))
401 +* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
541 541  
542 -(((
543 543  (% style="color:red" %)Note: DO3 is not valid for LT-22222-L.
544 -)))
545 545  
546 -(((
547 547  **To use this mode, please run:**
548 -)))
549 549  
550 550  (% class="box infomessage" %)
551 551  (((
552 -(((
553 553  **AT+MOD=5**
554 554  )))
555 -)))
556 556  
557 557  (% class="box infomessage" %)
558 558  (((
559 -(((
560 560  **ATZ**
561 561  )))
562 -)))
563 563  
564 -(((
565 -Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/#H3.3.2AT2BMOD3D22C28DoubleDICounting29]].
566 -)))
417 +Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:#COUNT_COMMAND]].
567 567  
568 568  === 3.3.6 AT+ADDMOD~=6. (Trigger Mode, Optional) ===
569 569  
... ... @@ -612,7 +612,7 @@
612 612  
613 613  **Downlink Command to set Trigger Condition**
614 614  
615 -Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
466 +Type Code: 0xAA. Downlink command same as AT Command [[AT+AVLIM, AT+ACLIM>>path:#AT_Trigger]]
616 616  
617 617  Format: AA xx yy1 yy1 yy2 yy2 yy3 yy3 yy4 yy4
618 618  
... ... @@ -632,7 +632,7 @@
632 632  
633 633  Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
634 634  
635 -**Example2**: AA 02 01 00
486 +Example2: AA 02 01 00
636 636  
637 637  Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
638 638  
... ... @@ -971,10 +971,8 @@
971 971  
972 972  (% class="box infomessage" %)
973 973  (((
974 -(((
975 975  **0xA9 aa bb cc     ~/~/ Set DO1/DO2/DO3 output with time control**
976 976  )))
977 -)))
978 978  
979 979  This is to control the digital output time of DO pin. Include four bytes:
980 980  
... ... @@ -1191,9 +1191,10 @@
1191 1191  
1192 1192  [[image:image-20220524094641-11.png||height="390" width="723"]]
1193 1193  
1043 +
1194 1194  [[image:image-20220524094641-12.png||height="402" width="718"]]
1195 1195  
1196 -**Step 3**: Create an account or log in Mydevices.
1046 +**Step **3: Create an account or log in Mydevices.
1197 1197  
1198 1198  **Step 4**: Search LT-22222-L(for both LT-22222-L / LT-33222-L) and add DevEUI.(% style="display:none" %)
1199 1199  
... ... @@ -1203,6 +1203,7 @@
1203 1203  
1204 1204  After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
1205 1205  
1056 +
1206 1206  [[image:image-20220524094909-1.png||height="335" width="729"]]
1207 1207  
1208 1208  [[image:image-20220524094909-2.png||height="337" width="729"]]
... ... @@ -1213,6 +1213,10 @@
1213 1213  
1214 1214  [[image:image-20220524094909-5.png||height="341" width="734"]]
1215 1215  
1067 +
1068 +
1069 +
1070 +
1216 1216  == 3.6 Interface Detail ==
1217 1217  
1218 1218  === 3.6.1 Digital Input Port: DI1/DI2 /DI3 ( For LT-33222-L, low active ) ===
... ... @@ -1228,10 +1228,8 @@
1228 1228  )))
1229 1229  
1230 1230  (((
1231 -(((
1232 1232  Internal circuit as below, the NEC2501 is a photocoupler, the Active current (from NEC2501 pin 1 to pin 2 is 1ma and the max current is 50mA. When there is active current pass NEC2501 pin1 to pin2. The DI will be active high
1233 1233  )))
1234 -)))
1235 1235  
1236 1236  [[image:1653357170703-587.png]]
1237 1237  
... ... @@ -1249,7 +1249,7 @@
1249 1249  
1250 1250  So when sensor active, the current between NEC2501 pin1 and pin2 is： ​​
1251 1251  
1252 -[[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]]** [[image:image-20220524095628-8.png]] = DI1+ / 1K.**
1105 + //IF// = DI1+ / 1K.
1253 1253  
1254 1254  If DI1+ = 12v, the //IF// = 12mA , So the LT-22222-L will be able to detect this active signal.
1255 1255  
... ... @@ -1263,9 +1263,9 @@
1263 1263  
1264 1264  So when sensor active, the current between NEC2501 pin1 and pin2 is:
1265 1265  
1266 -[[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]]** [[image:image-20220524095628-8.png]]= DI1+ / 1K.**
1119 +[[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]]** [[image:image-20220524095628-8.png]]= DI1+ / 1K.**
1267 1267  
1268 -If **DI1+ = 24v**, the [[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]]**[[image:image-20220524095628-8.png]]** = 24mA , So the LT-22222-L will be able to detect this high active signal.
1121 +If **DI1+ = 24v**, the [[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]]**[[image:image-20220524095628-8.png]]** = 24mA , So the LT-22222-L will be able to detect this high active signal.
1269 1269  
1270 1270  
1271 1271  **Example3**: Connect to a 220v high active sensor.
... ... @@ -1277,7 +1277,7 @@
1277 1277  
1278 1278  So when sensor active, the current between NEC2501 pin1 and pin2 is:
1279 1279  
1280 - [[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]]**[[image:image-20220524095628-8.png]] = DI1+ / 51K.**
1133 + [[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]]**[[image:image-20220524095628-8.png]] = DI1+ / 51K.**
1281 1281  
1282 1282  If sensor output is 220v, the (% id="cke_bm_243359S" style="display:none" %)[[image:image-20220524095628-8.png]](%%) = DI1+ / 51K.  = 4.3mA , So the LT-22222-L will be able to detect this high active signal safely.
1283 1283  
... ... @@ -1647,16 +1647,14 @@
1647 1647  ATZ
1648 1648  
1649 1649  = 5. FAQ =
1650 -
1651 1651  == 5.1 How to upgrade the image? ==
1652 -
1653 1653  The LT LoRaWAN Controller is shipped with a 3.5mm cable, the cable is used to upload image to LT to:
1654 1654  
1506 +
1655 1655  * Support new features
1656 1656  * For bug fix
1657 1657  * Change LoRaWAN bands.
1658 1658  Below shows the hardware connection for how to upload an image to the LT:
1659 -* [[image:1653359603330-121.png]]
1660 1660  
1661 1661  **Step1:** Download [[flash loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].
1662 1662  **Step2**: Download the [[LT Image files>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/image/]].
... ... @@ -1664,89 +1664,160 @@
1664 1664  **For LT-22222-L**:
1665 1665  Hold down the PRO button and then momentarily press the RST reset button and the **DO1 led** will change from OFF to ON. When **DO1 LED** is on, it means the device is in download mode.
1666 1666  
1667 - [[image:image-20220524103407-12.png]]
1518 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]]
1668 1668  
1669 -[[image:image-20220524103429-13.png]]
1520 +(% style="color:red" %)**Notice**: In case user has lost the program cable. User can hand made one from a 3.5mm cable. The pin mapping is:
1670 1670  
1671 -[[image:image-20220524104033-15.png]]
1672 1672  
1673 -(% style="color:red" %)**Notice**(%%): In case user has lost the program cable. User can hand made one from a 3.5mm cable. The pin mapping is:
1523 +1. (((
1524 +(((
1525 +
1526 +)))
1674 1674  
1675 -[[image:1653360054704-518.png||height="186" width="745"]]
1528 +1. (((
1529 +How to change the LoRa Frequency Bands/Region?
1530 +)))
1531 +)))
1676 1676  
1677 1677  (((
1534 +User can follow the introduction for [[how to upgrade image>>path:#upgrade_image]]. When download the images, choose the required image file for download.
1535 +)))
1536 +
1678 1678  (((
1679 -== 5.2 How to change the LoRa Frequency Bands/Region? ==
1538 +
1680 1680  )))
1540 +
1541 +1.
1542 +11. (((
1543 +How to set up LT to work with Single Channel Gateway such as LG01/LG02?
1681 1681  )))
1682 1682  
1683 1683  (((
1684 -User can follow the introduction for [[how to upgrade image>>path:http://8.211.40.43:8080/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/#H5.1Howtoupgradetheimage3F]]. When download the images, choose the required image file for download.
1547 +In this case, users need to set LT-33222-L to work in ABP mode & transmit in only one frequency.
1685 1685  )))
1686 1686  
1687 1687  (((
1688 -== 5.3 How to set up LT to work with Single Channel Gateway such as LG01/LG02? ==
1551 +Assume we have a LG02 working in the frequency 868400000 now , below is the step.
1689 1689  )))
1690 1690  
1691 1691  (((
1555 +
1556 +)))
1557 +
1692 1692  (((
1693 -In this case, users need to set LT-33222-L to work in ABP mode & transmit in only one frequency.
1559 +**Step1**: Log in TTN, Create an ABP device in the application and input the network session key (NETSKEY), app session key (APPSKEY) from the device.
1694 1694  )))
1561 +
1562 +(((
1563 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image039.png]]
1695 1695  )))
1696 1696  
1697 1697  (((
1567 +Note: user just need to make sure above three keys match, User can change either in TTN or Device to make then match. In TTN, NETSKEY and APPSKEY can be configured by user in setting page, but Device Addr is generated by TTN.
1568 +)))
1569 +
1698 1698  (((
1699 -Assume we have a LG02 working in the frequency 868400000 now , below is the step.
1571 +
1700 1700  )))
1573 +
1574 +(((
1575 +**Step2: **Run AT Command to make LT work in Single frequency & ABP mode. Below is the AT commands:
1701 1701  )))
1702 1702  
1703 1703  (((
1704 -(% style="color:#4f81bd" %)**Step1**(%%): Log in TTN, Create an ABP device in the application and input the network session key (NETSKEY), app session key (APPSKEY) from the device.
1579 +123456   Enter Password to have AT access.
1705 1705  )))
1706 1706  
1707 1707  (((
1708 -[[image:1653360231087-571.png||height="401" width="727"]]
1583 +AT+FDR   Reset Parameters to Factory Default, Keys Reserve
1709 1709  )))
1710 1710  
1711 -(% style="color:red" %)Note: user just need to make sure above three keys match, User can change either in TTN or Device to make then match. In TTN, NETSKEY and APPSKEY can be configured by user in setting page, but Device Addr is generated by TTN.
1586 +(((
1587 +123456   Enter Password to have AT access.
1588 +)))
1712 1712  
1713 -(% style="color:#4f81bd" %)**Step2**(%%)**: **Run AT Command to make LT work in Single frequency & ABP mode. Below is the AT commands:
1590 +(((
1591 +AT+NJM=0 Set to ABP mode
1592 +)))
1714 1714  
1715 -(% style="background-color:#dcdcdc" %)123456 (%%) Enter Password to have AT access.
1716 -(% style="background-color:#dcdcdc" %)AT+FDR  (%%) Reset Parameters to Factory Default, Keys Reserve
1717 -(% style="background-color:#dcdcdc" %)123456  (%%) Enter Password to have AT access.
1718 -(% style="background-color:#dcdcdc" %)AT+NJM=0 (%%)Set to ABP mode
1719 -(% style="background-color:#dcdcdc" %)AT+ADR=0 (%%)Set the Adaptive Data Rate Off
1720 -(% style="background-color:#dcdcdc" %)AT+DR=5 (%%) Set Data Rate (Set AT+DR=3 for 915 band)
1721 -(% style="background-color:#dcdcdc" %)AT+TDC=60000  (%%)Set transmit interval to 60 seconds
1722 -(% style="background-color:#dcdcdc" %)AT+CHS=868400000 (%%)Set transmit frequency to 868.4Mhz
1723 -(% style="background-color:#dcdcdc" %)AT+DADDR=26 01 1A F1(%%) Set Device Address to 26 01 1A F1
1724 -(% style="background-color:#dcdcdc" %)ATZ                (%%)Reset MCU
1594 +(((
1595 +AT+ADR=0 Set the Adaptive Data Rate Off
1596 +)))
1725 1725  
1598 +(((
1599 +AT+DR=5  Set Data Rate (Set AT+DR=3 for 915 band)
1600 +)))
1601 +
1602 +(((
1603 +AT+TDC=60000  Set transmit interval to 60 seconds
1604 +)))
1605 +
1606 +(((
1607 +AT+CHS=868400000 Set transmit frequency to 868.4Mhz
1608 +)))
1609 +
1610 +(((
1611 +AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1
1612 +)))
1613 +
1614 +(((
1615 +ATZ                Reset MCU
1616 +)))
1617 +
1618 +(((
1726 1726  As shown in below:
1620 +)))
1727 1727  
1728 -[[image:1653360498588-932.png||height="485" width="726"]]
1622 +(((
1623 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image040.png]]
1624 +)))
1729 1729  
1730 -== 5.4 Can I see counting event in Serial? ==
1626 +(((
1627 +
1628 +)))
1731 1731  
1732 1732  (((
1631 +
1632 +)))
1633 +
1634 +1. (((
1635 +(((
1636 +
1637 +)))
1638 +
1639 +1. (((
1640 +Can I see counting event in Serial?
1641 +)))
1642 +)))
1643 +
1644 +(((
1733 1733  User can run AT+DEBUG command to see the counting event in serial. If firmware too old and doesn’t support AT+DEBUG. User can update to latest firmware first.
1734 1734  )))
1735 1735  
1736 1736  (((
1737 -= 6. Trouble Shooting =
1649 +
1738 1738  )))
1739 1739  
1740 1740  (((
1653 +
1654 +)))
1655 +
1741 1741  (((
1742 -== 6.1 Downlink doesn’t work, how to solve it? ==
1657 +
1743 1743  )))
1659 +
1660 +1. (((
1661 +(((
1662 +Trouble Shooting    
1744 1744  )))
1745 1745  
1665 +1. (((
1666 +Downlink doesn’t work, how to solve it?
1667 +)))
1668 +)))
1669 +
1746 1746  (((
1747 1747  Please see this link for how to debug:
1748 -
1749 -[[http:~~/~~/8.211.40.43:8080/xwiki/bin/view/Main/LoRaWAN%20Communication%20Debug/>>http://8.211.40.43:8080/xwiki/bin/view/Main/LoRaWAN%20Communication%20Debug/]]
1750 1750  )))
1751 1751  
1752 1752  (((
... ... @@ -1754,9 +1754,14 @@
1754 1754  )))
1755 1755  
1756 1756  (((
1757 -== 6.2 Have trouble to upload image. ==
1679 +
1758 1758  )))
1759 1759  
1682 +1.
1683 +11. (((
1684 +Have trouble to upload image.
1685 +)))
1686 +
1760 1760  (((
1761 1761  See this link for trouble shooting:
1762 1762  )))
... ... @@ -1766,9 +1766,14 @@
1766 1766  )))
1767 1767  
1768 1768  (((
1769 -== 6.3 Why I can’t join TTN in US915 /AU915 bands? ==
1696 +
1770 1770  )))
1771 1771  
1699 +1.
1700 +11. (((
1701 +Why I can’t join TTN in US915 /AU915 bands?
1702 +)))
1703 +
1772 1772  (((
1773 1773  It might be about the channels mapping. Please see this link for detail:
1774 1774  )))
... ... @@ -1778,111 +1778,106 @@
1778 1778  )))
1779 1779  
1780 1780  (((
1781 -= 7. Order Info =
1713 +
1782 1782  )))
1783 1783  
1784 1784  (((
1717 +
1718 +)))
1719 +
1785 1785  (((
1786 -(% style="color:#4f81bd" %)**LT-22222-L-XXX:**
1721 +
1787 1787  )))
1723 +
1724 +1. (((
1725 +Order Info
1788 1788  )))
1789 1789  
1790 1790  (((
1729 +**For LT-33222-L-XXX or LT-22222-L-XXX:**
1730 +)))
1731 +
1791 1791  (((
1792 -(% style="color:#4f81bd" %)**XXX:**
1733 +**XXX:**
1793 1793  )))
1794 -)))
1795 1795  
1796 1796  * (((
1797 -(% style="color:#4f81bd" %)**EU433**(%%): LT with frequency bands EU433
1737 +**EU433**: LT with frequency bands EU433
1798 1798  )))
1799 1799  * (((
1800 -(% style="color:#4f81bd" %)**EU868**(%%): LT with frequency bands EU868
1740 +**EU868**: LT with frequency bands EU868
1801 1801  )))
1802 1802  * (((
1803 -(% style="color:#4f81bd" %)**KR920**(%%): LT with frequency bands KR920
1743 +**KR920**: LT with frequency bands KR920
1804 1804  )))
1805 1805  * (((
1806 -(% style="color:#4f81bd" %)**CN470**(%%): LT with frequency bands CN470
1746 +**CN470**: LT with frequency bands CN470
1807 1807  )))
1808 1808  * (((
1809 -(% style="color:#4f81bd" %)**AS923**(%%): LT with frequency bands AS923
1749 +**AS923**: LT with frequency bands AS923
1810 1810  )))
1811 1811  * (((
1812 -(% style="color:#4f81bd" %)**AU915**(%%): LT with frequency bands AU915
1752 +**AU915**: LT with frequency bands AU915
1813 1813  )))
1814 1814  * (((
1815 -(% style="color:#4f81bd" %)**US915**(%%): LT with frequency bands US915
1755 +**US915**: LT with frequency bands US915
1816 1816  )))
1817 1817  * (((
1818 -(% style="color:#4f81bd" %)**IN865**(%%): LT with frequency bands IN865
1758 +**IN865**: LT with frequency bands IN865
1819 1819  )))
1760 +* (((
1761 +**CN779**: LT with frequency bands CN779
1762 +)))
1820 1820  
1821 -(((
1822 -* (% style="color:#4f81bd" %)**CN779**(%%): LT with frequency bands CN779
1823 -
1824 -= 8. Packing Info =
1764 +1. (((
1765 +Packing Info
1825 1825  )))
1826 1826  
1827 1827  (((
1828 -(((
1829 1829  **Package Includes**:
1830 1830  )))
1831 -)))
1832 1832  
1833 -(((
1834 -(((
1835 -* LT-22222-L I/O Controller x 1
1836 -* Stick Antenna for LoRa RF part x 1
1837 -* Bracket for controller x1
1838 -* Program cable x 1
1772 +* (((
1773 +LT I/O Controller x 1
1839 1839  )))
1775 +* (((
1776 +Stick Antenna for LoRa RF part x 1
1840 1840  )))
1778 +* (((
1779 +Bracket for controller x1
1780 +)))
1781 +* (((
1782 +Program cable x 1
1783 +)))
1841 1841  
1842 1842  (((
1843 -(((
1844 1844  **Dimension and weight**:
1845 1845  )))
1846 -)))
1847 1847  
1848 -(((
1849 -(((
1850 -* Device Size: 13.5 x 7 x 3 cm
1851 -* Device Weight: 105g
1852 -* Package Size / pcs : 14.5 x 8 x 5 cm
1853 -* Weight / pcs : 170g
1789 +* (((
1790 +Device Size: 13.5 x 7 x 3 cm
1854 1854  )))
1792 +* (((
1793 +Device Weight: 105g
1855 1855  )))
1795 +* (((
1796 +Package Size / pcs : 14.5 x 8 x 5 cm
1797 +)))
1798 +* (((
1799 +Weight / pcs : 170g
1800 +)))
1856 1856  
1857 -(((
1858 -= 9. Support =
1802 +1. (((
1803 +Support
1859 1859  )))
1860 1860  
1861 1861  * (((
1862 -(((
1863 1863  Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
1864 1864  )))
1865 -)))
1866 1866  * (((
1867 -(((
1868 1868  Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to
1869 1869  )))
1870 -)))
1871 1871  
1872 1872  (((
1873 -(((
1874 - [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]
1814 +[[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]
1875 1875  )))
1876 -
1877 -(((
1878 -= 10. Reference​​​​​ =
1879 -
1880 -* Product Page:
1881 -
1882 -LT-22222-L: [[http:~~/~~/www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html]]
1883 -
1884 -* [[Image Download>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/image/]]
1885 -* [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/]]
1886 -* [[Hardware Source>>url:https://github.com/dragino/Lora/tree/master/LT/LT-33222-L/v1.0]]
1887 -)))
1888 -)))
1653360054704-518.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -84.7 KB
Content
1653360231087-571.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -94.8 KB
Content
1653360498588-932.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -93.9 KB
Content
image-20220524103652-14.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -88.6 KB
Content
image-20220524104033-15.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -83.7 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0