Last modified by Saxer Lin on 2025/04/15 17:24
<
From version < 55.1 >
edited by Xiaoling
on 2022/05/24 10:07
To version < 68.12 >
edited by Xiaoling
on 2022/05/25 15:13
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -45,44 +45,114 @@
45 45  
46 46  == 1.2  Specifications ==
47 47  
48 +(((
48 48  **Hardware System:**
50 +)))
49 49  
50 -* STM32L072CZT6 MCU
51 -* SX1276/78 Wireless Chip 
52 -* Power Consumption:
53 -** Idle: 4mA@12v
54 -** 20dB Transmit: 34mA@12v
52 +* (((
53 +STM32L072CZT6 MCU
54 +)))
55 +* (((
56 +SX1276/78 Wireless Chip 
57 +)))
58 +* (((
59 +(((
60 +Power Consumption:
61 +)))
55 55  
63 +* (((
64 +Idle: 4mA@12v
65 +)))
66 +* (((
67 +20dB Transmit: 34mA@12v
68 +)))
69 +)))
70 +
71 +(((
56 56  **Interface for Model: LT22222-L:**
73 +)))
57 57  
58 -* 2 x Digital dual direction Input (Detect High/Low signal, Max: 50v, or 220v with optional external resistor)
59 -* 2 x Digital Output (NPN output. Max pull up voltage 36V,450mA)
60 -* 2 x Relay Output (5A@250VAC / 30VDC)
61 -* 2 x 0~~20mA Analog Input (res:0.01mA)
62 -* 2 x 0~~30V Analog Input (res:0.01v)
63 -* Power Input 7~~ 24V DC. 
75 +* (((
76 +2 x Digital dual direction Input (Detect High/Low signal, Max: 50v, or 220v with optional external resistor)
77 +)))
78 +* (((
79 +2 x Digital Output (NPN output. Max pull up voltage 36V,450mA)
80 +)))
81 +* (((
82 +2 x Relay Output (5A@250VAC / 30VDC)
83 +)))
84 +* (((
85 +2 x 0~~20mA Analog Input (res:0.01mA)
86 +)))
87 +* (((
88 +2 x 0~~30V Analog Input (res:0.01v)
89 +)))
90 +* (((
91 +Power Input 7~~ 24V DC. 
92 +)))
64 64  
94 +(((
65 65  **LoRa Spec:**
96 +)))
66 66  
67 -* Frequency Range:
68 -** Band 1 (HF): 862 ~~ 1020 Mhz
69 -** Band 2 (LF): 410 ~~ 528 Mhz
70 -* 168 dB maximum link budget.
71 -* +20 dBm - 100 mW constant RF output vs.
72 -* +14 dBm high efficiency PA.
73 -* Programmable bit rate up to 300 kbps.
74 -* High sensitivity: down to -148 dBm.
75 -* Bullet-proof front end: IIP3 = -12.5 dBm.
76 -* Excellent blocking immunity.
77 -* Low RX current of 10.3 mA, 200 nA register retention.
78 -* Fully integrated synthesizer with a resolution of 61 Hz.
79 -* FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.
80 -* Built-in bit synchronizer for clock recovery.
81 -* Preamble detection.
82 -* 127 dB Dynamic Range RSSI.
83 -* Automatic RF Sense and CAD with ultra-fast AFC.
84 -* Packet engine up to 256 bytes with CRC.
98 +* (((
99 +(((
100 +Frequency Range:
101 +)))
85 85  
103 +* (((
104 +Band 1 (HF): 862 ~~ 1020 Mhz
105 +)))
106 +* (((
107 +Band 2 (LF): 410 ~~ 528 Mhz
108 +)))
109 +)))
110 +* (((
111 +168 dB maximum link budget.
112 +)))
113 +* (((
114 ++20 dBm - 100 mW constant RF output vs.
115 +)))
116 +* (((
117 ++14 dBm high efficiency PA.
118 +)))
119 +* (((
120 +Programmable bit rate up to 300 kbps.
121 +)))
122 +* (((
123 +High sensitivity: down to -148 dBm.
124 +)))
125 +* (((
126 +Bullet-proof front end: IIP3 = -12.5 dBm.
127 +)))
128 +* (((
129 +Excellent blocking immunity.
130 +)))
131 +* (((
132 +Low RX current of 10.3 mA, 200 nA register retention.
133 +)))
134 +* (((
135 +Fully integrated synthesizer with a resolution of 61 Hz.
136 +)))
137 +* (((
138 +FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.
139 +)))
140 +* (((
141 +Built-in bit synchronizer for clock recovery.
142 +)))
143 +* (((
144 +Preamble detection.
145 +)))
146 +* (((
147 +127 dB Dynamic Range RSSI.
148 +)))
149 +* (((
150 +Automatic RF Sense and CAD with ultra-fast AFC.
151 +)))
152 +* (((
153 +Packet engine up to 256 bytes with CRC.
154 +)))
155 +
86 86  == 1.3 Features ==
87 87  
88 88  * LoRaWAN Class A & Class C protocol
... ... @@ -129,17 +129,22 @@
129 129  
130 130  == 3.1 How it works? ==
131 131  
202 +(((
132 132  The LT is configured as LoRaWAN OTAA Class C mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the LT. It will auto join the network via OTAA. For LT-22222-L, the LED will show the Join status: After power on **TX LED** will fast blink 5 times, LT-22222-L will enter working mode and start to JOIN LoRaWAN network. **TX LED** will be on for 5 seconds after joined in network. When there is message from server, the **RX LED** will be on for 1 second. 
204 +)))
133 133  
134 -In case user can’t set the OTAA keys in the network server and has to use the existing keys from server. User can [[use AT Command>>path:#AT_Command]] to set the keys in the devices.
206 +(((
207 +In case user can’t set the OTAA keys in the network server and has to use the existing keys from server. User can [[use AT Command>>||anchor="H4.UseATCommand"]] to set the keys in the devices.
208 +)))
135 135  
136 -3.2 Example to join LoRaWAN network
210 +== 3.2 Example to join LoRaWAN network ==
137 137  
212 +(((
138 138  This chapter shows an example for how to join the TTN LoRaWAN Network. Below is the network structure, we use our LG308 as LoRaWAN gateway here. 
214 +)))
139 139  
140 140  [[image:image-20220523172350-1.png||height="266" width="864"]]
141 141  
142 -
143 143  (((
144 144  The LG308 is already set to connect to [[TTN network >>url:https://www.thethingsnetwork.org/]]. So what we need to do now is only configure register this device to TTN:
145 145  )))
... ... @@ -235,7 +235,9 @@
235 235  
236 236  **For LT-22222-L**: this mode the **DI1 and DI2** are used as counting pins.
237 237  
313 +(((
238 238  Total : 11 bytes payload
315 +)))
239 239  
240 240  [[image:image-20220523180452-3.png]]
241 241  
... ... @@ -249,53 +249,77 @@
249 249  * FIRST: Indicate this is the first packet after join network.
250 250  * DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
251 251  
329 +(((
252 252  (% style="color:red" %)Note: DO3 bit is not valid for LT-22222-L.
331 +)))
253 253  
333 +(((
254 254  **To use counting mode, please run:**
335 +)))
255 255  
256 256  (% class="box infomessage" %)
257 257  (((
339 +(((
258 258  **AT+MOD=2**
259 259  )))
342 +)))
260 260  
261 261  (% class="box infomessage" %)
262 262  (((
346 +(((
263 263  **ATZ**
264 264  )))
349 +)))
265 265  
351 +(((
266 266  (% style="color:#4f81bd" %)**AT Commands for counting:**
353 +)))
267 267  
355 +(((
268 268  **For LT22222-L:**
357 +)))
269 269  
270 270  (% class="box infomessage" %)
271 271  (((
361 +(((
272 272  **AT+TRIG1=0,100 (set DI1 port to trigger on low level, valid signal is 100ms) **
273 273  )))
364 +)))
274 274  
275 275  (% class="box infomessage" %)
276 276  (((
368 +(((
277 277  **AT+TRIG1=1,100(set DI1 port to trigger on high level, valid signal is 100ms ) **
278 278  )))
371 +)))
279 279  
280 280  (% class="box infomessage" %)
281 281  (((
375 +(((
282 282  **AT+TRIG2=0,100 (set DI2 port to trigger on low level, valid signal is 100ms) **
283 283  )))
378 +)))
284 284  
285 285  (% class="box infomessage" %)
286 286  (((
382 +(((
287 287  **AT+TRIG2=1,100 (set DI2 port to trigger on high level, valid signal is 100ms ) **
288 288  )))
385 +)))
289 289  
290 290  (% class="box infomessage" %)
291 291  (((
389 +(((
292 292  **AT+SETCNT=1,60   (Set COUNT1 value to 60)**
293 293  )))
392 +)))
294 294  
295 295  (% class="box infomessage" %)
296 296  (((
396 +(((
297 297  **AT+SETCNT=2,60   (Set COUNT2 value to 60)**
298 298  )))
399 +)))
299 299  
300 300  === 3.3.3 AT+MOD~=3, Single DI Counting + 2 x ACI ===
301 301  
... ... @@ -313,21 +313,31 @@
313 313  * FIRST: Indicate this is the first packet after join network.
314 314  * DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
315 315  
417 +(((
316 316  (% style="color:red" %)Note: DO3 is not valid for LT-22222-L.
419 +)))
317 317  
421 +(((
318 318  **To use counting mode, please run:**
423 +)))
319 319  
320 320  (% class="box infomessage" %)
321 321  (((
427 +(((
322 322  **AT+MOD=3**
323 323  )))
430 +)))
324 324  
325 325  (% class="box infomessage" %)
326 326  (((
434 +(((
327 327  **ATZ**
328 328  )))
437 +)))
329 329  
330 -Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:#COUNT_COMMAND]].
439 +(((
440 +Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
441 +)))
331 331  
332 332  === 3.3.4 AT+MOD~=4, Single DI Counting + 1 x Voltage Counting ===
333 333  
... ... @@ -347,44 +347,67 @@
347 347  * FIRST: Indicate this is the first packet after join network.
348 348  * DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
349 349  
461 +(((
350 350  (% style="color:red" %)Note: DO3 is not valid for LT-22222-L.
463 +)))
351 351  
465 +(((
352 352  **To use this mode, please run:**
467 +)))
353 353  
354 354  (% class="box infomessage" %)
355 355  (((
471 +(((
356 356  **AT+MOD=4**
357 357  )))
474 +)))
358 358  
359 359  (% class="box infomessage" %)
360 360  (((
478 +(((
361 361  **ATZ**
362 362  )))
481 +)))
363 363  
483 +(((
484 +
485 +)))
364 364  
365 -Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:#COUNT_COMMAND]].
487 +(((
488 +Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
489 +)))
366 366  
491 +(((
367 367  **Plus below command for AVI1 Counting:**
493 +)))
368 368  
369 369  (% class="box infomessage" %)
370 370  (((
497 +(((
371 371  **AT+SETCNT=3,60   (set AVI Count to 60)**
372 372  )))
500 +)))
373 373  
374 374  (% class="box infomessage" %)
375 375  (((
504 +(((
376 376  **AT+VOLMAX=20000   (If AVI1 voltage higher than VOLMAX (20000mV =20v), counter increase 1)**
377 377  )))
507 +)))
378 378  
379 379  (% class="box infomessage" %)
380 380  (((
511 +(((
381 381  **AT+VOLMAX=20000,0   (If AVI1 voltage lower than VOLMAX (20000mV =20v), counter increase 1)**
382 382  )))
514 +)))
383 383  
384 384  (% class="box infomessage" %)
385 385  (((
518 +(((
386 386  **AT+VOLMAX=20000,1   (If AVI1 voltage higer than VOLMAX (20000mV =20v), counter increase 1)**
387 387  )))
521 +)))
388 388  
389 389  === 3.3.5 AT+MOD~=5, Single DI Counting + 2 x AVI + 1 x ACI ===
390 390  
... ... @@ -398,23 +398,35 @@
398 398  
399 399  * RO is for relay. ROx=1 : close，ROx=0 always open.
400 400  * FIRST: Indicate this is the first packet after join network.
401 -* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
535 +* (((
536 +DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
537 +)))
402 402  
539 +(((
403 403  (% style="color:red" %)Note: DO3 is not valid for LT-22222-L.
541 +)))
404 404  
543 +(((
405 405  **To use this mode, please run:**
545 +)))
406 406  
407 407  (% class="box infomessage" %)
408 408  (((
549 +(((
409 409  **AT+MOD=5**
410 410  )))
552 +)))
411 411  
412 412  (% class="box infomessage" %)
413 413  (((
556 +(((
414 414  **ATZ**
415 415  )))
559 +)))
416 416  
417 -Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:#COUNT_COMMAND]].
561 +(((
562 +Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
563 +)))
418 418  
419 419  === 3.3.6 AT+ADDMOD~=6. (Trigger Mode, Optional) ===
420 420  
... ... @@ -463,7 +463,7 @@
463 463  
464 464  **Downlink Command to set Trigger Condition**
465 465  
466 -Type Code: 0xAA. Downlink command same as AT Command [[AT+AVLIM, AT+ACLIM>>path:#AT_Trigger]]
612 +Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
467 467  
468 468  Format: AA xx yy1 yy1 yy2 yy2 yy3 yy3 yy4 yy4
469 469  
... ... @@ -483,7 +483,7 @@
483 483  
484 484  Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
485 485  
486 -Example2: AA 02 01 00
632 +**Example2**: AA 02 01 00
487 487  
488 488  Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
489 489  
... ... @@ -556,7 +556,7 @@
556 556  
557 557  === 3.4.1 Common Commands ===
558 558  
559 -They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>http://8.211.40.43:8080/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
705 +They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
560 560  
561 561  === 3.4.2 Sensor related commands ===
562 562  
... ... @@ -822,8 +822,10 @@
822 822  
823 823  (% class="box infomessage" %)
824 824  (((
971 +(((
825 825  **0xA9 aa bb cc     ~/~/ Set DO1/DO2/DO3 output with time control**
826 826  )))
974 +)))
827 827  
828 828  This is to control the digital output time of DO pin. Include four bytes:
829 829  
... ... @@ -1026,24 +1026,29 @@
1026 1026  **0x A7 aa bb cc     ~/~/ same as AT+COUTIME =aa bb cc,**
1027 1027  )))
1028 1028  
1177 +(((
1029 1029  range: aa bb cc:0 to 16777215,  (unit:second)
1179 +)))
1030 1030  
1031 1031  == 3.5 Integrate with Mydevice ==
1032 1032  
1033 1033  Mydevices provides a human friendly interface to show the sensor data, once we have data in TTN, we can use Mydevices to connect to TTN and see the data in Mydevices. Below are the steps:
1034 1034  
1185 +(((
1035 1035  **Step 1**: Be sure that your device is programmed and properly connected to the network at this time.
1187 +)))
1036 1036  
1189 +(((
1037 1037  **Step 2**: To configure the Application to forward data to Mydevices you will need to add integration. To add the Mydevices integration, perform the following steps:
1191 +)))
1038 1038  
1039 1039  [[image:1653356737703-362.png||height="232" width="732"]]
1040 1040  
1041 1041  [[image:image-20220524094641-11.png||height="390" width="723"]]
1042 1042  
1043 -
1044 1044  [[image:image-20220524094641-12.png||height="402" width="718"]]
1045 1045  
1046 -**Step **3: Create an account or log in Mydevices.
1199 +**Step 3**: Create an account or log in Mydevices.
1047 1047  
1048 1048  **Step 4**: Search LT-22222-L(for both LT-22222-L / LT-33222-L) and add DevEUI.(% style="display:none" %)
1049 1049  
... ... @@ -1053,7 +1053,6 @@
1053 1053  
1054 1054  After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
1055 1055  
1056 -
1057 1057  [[image:image-20220524094909-1.png||height="335" width="729"]]
1058 1058  
1059 1059  [[image:image-20220524094909-2.png||height="337" width="729"]]
... ... @@ -1064,10 +1064,6 @@
1064 1064  
1065 1065  [[image:image-20220524094909-5.png||height="341" width="734"]]
1066 1066  
1067 -
1068 -
1069 -
1070 -
1071 1071  == 3.6 Interface Detail ==
1072 1072  
1073 1073  === 3.6.1 Digital Input Port: DI1/DI2 /DI3 ( For LT-33222-L, low active ) ===
... ... @@ -1083,8 +1083,10 @@
1083 1083  )))
1084 1084  
1085 1085  (((
1234 +(((
1086 1086  Internal circuit as below, the NEC2501 is a photocoupler, the Active current (from NEC2501 pin 1 to pin 2 is 1ma and the max current is 50mA. When there is active current pass NEC2501 pin1 to pin2. The DI will be active high
1087 1087  )))
1237 +)))
1088 1088  
1089 1089  [[image:1653357170703-587.png]]
1090 1090  
... ... @@ -1102,7 +1102,7 @@
1102 1102  
1103 1103  So when sensor active, the current between NEC2501 pin1 and pin2 is： ​​
1104 1104  
1105 - //IF// = DI1+ / 1K.
1255 +[[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]]** [[image:image-20220524095628-8.png]] = DI1+ / 1K.**
1106 1106  
1107 1107  If DI1+ = 12v, the //IF// = 12mA , So the LT-22222-L will be able to detect this active signal.
1108 1108  
... ... @@ -1116,9 +1116,9 @@
1116 1116  
1117 1117  So when sensor active, the current between NEC2501 pin1 and pin2 is:
1118 1118  
1119 -[[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png]]** [[image:image-20220524095628-8.png]]= DI1+ / 1K.**
1269 +[[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]]** [[image:image-20220524095628-8.png]]= DI1+ / 1K.**
1120 1120  
1121 -If **DI1+ = 24v**, the [[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png]]**[[image:image-20220524095628-8.png]]** = 24mA , So the LT-22222-L will be able to detect this high active signal.
1271 +If **DI1+ = 24v**, the [[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]]**[[image:image-20220524095628-8.png]]** = 24mA , So the LT-22222-L will be able to detect this high active signal.
1122 1122  
1123 1123  
1124 1124  **Example3**: Connect to a 220v high active sensor.
... ... @@ -1130,9 +1130,9 @@
1130 1130  
1131 1131  So when sensor active, the current between NEC2501 pin1 and pin2 is:
1132 1132  
1133 - [[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png]]**[[image:image-20220524095628-8.png]] = DI1+ / 51K.**
1283 + [[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]][[image:/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LT-22222-L/WebHome/image-20220524095628-8.png?rev=1.1||alt="image-20220524095628-8.png"]]**[[image:image-20220524095628-8.png]] = DI1+ / 51K.**
1134 1134  
1135 -If sensor output is 220v, the (% id="cke_bm_243359S" style="display:none" %) [[image:image-20220524095628-8.png]](%%) = DI1+ / 51K.  = 4.3mA , So the LT-22222-L will be able to detect this high active signal safely.
1285 +If sensor output is 220v, the (% id="cke_bm_243359S" style="display:none" %)[[image:image-20220524095628-8.png]](%%) = DI1+ / 51K.  = 4.3mA , So the LT-22222-L will be able to detect this high active signal safely.
1136 1136  
1137 1137  === 3.6.3 Digital Output Port: DO1/DO2 /DO3 ===
1138 1138  
... ... @@ -1169,415 +1169,615 @@
1169 1169  
1170 1170  === 3.6.5 Relay Output ===
1171 1171  
1322 +(((
1172 1172  The LT serial controller has two relay interfaces; each interface uses two pins of the screw terminal. User can connect other device’s Power Line to in serial of RO1_1 and RO_2. Such as below:
1324 +)))
1173 1173  
1174 -
1175 1175  [[image:image-20220524100215-9.png]]
1176 1176  
1177 -
1178 1178  [[image:image-20220524100215-10.png||height="382" width="723"]]
1179 1179  
1330 +== 3.7 LEDs Indicators ==
1180 1180  
1332 +[[image:image-20220524100748-11.png]]
1181 1181  
1334 += 4. Use AT Command =
1182 1182  
1336 +== 4.1 Access AT Command ==
1183 1183  
1338 +LT supports AT Command set. User can use a USB to TTL adapter plus the 3.5mm Program Cable to connect to LT for using AT command, as below.
1184 1184  
1185 -1.
1186 -11. LEDs Indicators
1340 +[[image:1653358238933-385.png]]
1187 1187  
1188 -(% border="1" style="background-color:#f7faff" %)
1189 -|**LEDs**|**Feature**
1190 -|**PWR**|Always on if there is power
1191 -|**SYS**|After device is powered on, the SYS will **fast blink in GREEN** for 5 times, means RS485-LN start to join LoRaWAN network. If join success, SYS will be **on GREEN for 5 seconds. **SYS will **blink Blue** on every upload and **blink Green** once receive a downlink message.
1192 -|**TX**|(((
1193 -Device boot: TX blinks 5 times.
1194 -
1195 -Successful join network: TX ON for 5 seconds.
1196 -
1197 -Transmit a LoRa packet: TX blinks once
1342 +(((
1343 +In PC, User needs to set (% style="color:#4f81bd" %)**serial tool**(%%)(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to (% style="color:green" %)**9600**(%%) to access to access serial console for LT. The AT commands are disable by default and need to enter password (default:(% style="color:green" %)**123456**)(%%) to active it. As shown below:
1198 1198  )))
1199 -|**RX**|RX blinks once when receive a packet.
1200 -|**DO1**|
1201 -|**DO2**|
1202 -|**DO3**|
1203 -|**DI2**|(((
1204 -For LT-22222-L: ON when DI2 is high, LOW when DI2 is low
1205 1205  
1206 -For LT-33222-L: ON when DI2 is low, LOW when DI2 is high
1207 -)))
1208 -|**DI2**|(((
1209 -For LT-22222-L: ON when DI2 is high, LOW when DI2 is low
1346 +[[image:1653358355238-883.png]]
1210 1210  
1211 -For LT-33222-L: ON when DI2 is low, LOW when DI2 is high
1348 +(((
1349 +More detail AT Command manual can be found at [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/]]
1212 1212  )))
1213 -|**DI3**|For LT-33222-L ONLY: ON when DI3 is low, LOW when DI3 is high
1214 -|**DI2**|(((
1215 -For LT-22222-L: ON when DI2 is high, LOW when DI2 is low
1216 1216  
1217 -For LT-33222-L: ON when DI2 is low, LOW when DI2 is high
1352 +(((
1353 +AT+<CMD>?        : Help on <CMD>
1218 1218  )))
1219 -|**RO1**|
1220 -|**RO2**|
1221 1221  
1222 -1. Use AT Command
1223 -11. Access AT Command
1224 -
1225 -LT supports AT Command set. User can use a USB to TTL adapter plus the 3.5mm Program Cable to connect to LT for using AT command, as below.
1226 -
1227 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]
1228 -
1229 -
1230 -In PC, User needs to set **serial tool**(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to **9600** to access to access serial console for LT. The AT commands are disable by default and need to enter password (default:**123456**) to active it. As shown below:
1231 -
1232 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]
1233 -
1234 -
1235 -More detail AT Command manual can be found at [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/]]
1236 -
1237 -AT+<CMD>?        : Help on <CMD>
1238 -
1356 +(((
1239 1239  AT+<CMD>         : Run <CMD>
1358 +)))
1240 1240  
1360 +(((
1241 1241  AT+<CMD>=<value> : Set the value
1362 +)))
1242 1242  
1364 +(((
1243 1243  AT+<CMD>=?       : Get the value
1366 +)))
1244 1244  
1368 +(((
1245 1245  ATZ: Trig a reset of the MCU
1370 +)))
1246 1246  
1372 +(((
1247 1247  AT+FDR: Reset Parameters to Factory Default, Keys Reserve 
1374 +)))
1248 1248  
1376 +(((
1249 1249  AT+DEUI: Get or Set the Device EUI
1378 +)))
1250 1250  
1380 +(((
1251 1251  AT+DADDR: Get or Set the Device Address
1382 +)))
1252 1252  
1384 +(((
1253 1253  AT+APPKEY: Get or Set the Application Key
1386 +)))
1254 1254  
1388 +(((
1255 1255  AT+NWKSKEY: Get or Set the Network Session Key
1390 +)))
1256 1256  
1392 +(((
1257 1257  AT+APPSKEY: Get or Set the Application Session Key
1394 +)))
1258 1258  
1396 +(((
1259 1259  AT+APPEUI: Get or Set the Application EUI
1398 +)))
1260 1260  
1400 +(((
1261 1261  AT+ADR: Get or Set the Adaptive Data Rate setting. (0: off, 1: on)
1402 +)))
1262 1262  
1404 +(((
1263 1263  AT+TXP: Get or Set the Transmit Power (0-5, MAX:0, MIN:5, according to LoRaWAN Spec)
1406 +)))
1264 1264  
1408 +(((
1265 1265  AT+DR: Get or Set the Data Rate. (0-7 corresponding to DR_X)  
1410 +)))
1266 1266  
1412 +(((
1267 1267  AT+DCS: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing
1414 +)))
1268 1268  
1416 +(((
1269 1269  AT+PNM: Get or Set the public network mode. (0: off, 1: on)
1418 +)))
1270 1270  
1420 +(((
1271 1271  AT+RX2FQ: Get or Set the Rx2 window frequency
1422 +)))
1272 1272  
1424 +(((
1273 1273  AT+RX2DR: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
1426 +)))
1274 1274  
1428 +(((
1275 1275  AT+RX1DL: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
1430 +)))
1276 1276  
1432 +(((
1277 1277  AT+RX2DL: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
1434 +)))
1278 1278  
1436 +(((
1279 1279  AT+JN1DL: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms
1438 +)))
1280 1280  
1440 +(((
1281 1281  AT+JN2DL: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms
1442 +)))
1282 1282  
1444 +(((
1283 1283  AT+NJM: Get or Set the Network Join Mode. (0: ABP, 1: OTAA)
1446 +)))
1284 1284  
1448 +(((
1285 1285  AT+NWKID: Get or Set the Network ID
1450 +)))
1286 1286  
1452 +(((
1287 1287  AT+FCU: Get or Set the Frame Counter Uplink
1454 +)))
1288 1288  
1456 +(((
1289 1289  AT+FCD: Get or Set the Frame Counter Downlink
1458 +)))
1290 1290  
1460 +(((
1291 1291  AT+CLASS: Get or Set the Device Class
1462 +)))
1292 1292  
1464 +(((
1293 1293  AT+JOIN: Join network
1466 +)))
1294 1294  
1468 +(((
1295 1295  AT+NJS: Get OTAA Join Status
1470 +)))
1296 1296  
1472 +(((
1297 1297  AT+SENDB: Send hexadecimal data along with the application port
1474 +)))
1298 1298  
1476 +(((
1299 1299  AT+SEND: Send text data along with the application port
1478 +)))
1300 1300  
1480 +(((
1301 1301  AT+RECVB: Print last received data in binary format (with hexadecimal values)
1482 +)))
1302 1302  
1484 +(((
1303 1303  AT+RECV: Print last received data in raw format
1486 +)))
1304 1304  
1488 +(((
1305 1305  AT+VER: Get current image version and Frequency Band
1490 +)))
1306 1306  
1492 +(((
1307 1307  AT+CFM: Get or Set the confirmation mode (0-1)
1494 +)))
1308 1308  
1496 +(((
1309 1309  AT+CFS: Get confirmation status of the last AT+SEND (0-1)
1498 +)))
1310 1310  
1500 +(((
1311 1311  AT+SNR: Get the SNR of the last received packet
1502 +)))
1312 1312  
1504 +(((
1313 1313  AT+RSSI: Get the RSSI of the last received packet
1506 +)))
1314 1314  
1508 +(((
1315 1315  AT+TDC: Get or set the application data transmission interval in ms
1510 +)))
1316 1316  
1512 +(((
1317 1317  AT+PORT: Get or set the application port
1514 +)))
1318 1318  
1516 +(((
1319 1319  AT+DISAT: Disable AT commands
1518 +)))
1320 1320  
1520 +(((
1321 1321  AT+PWORD: Set password, max 9 digits
1522 +)))
1322 1322  
1524 +(((
1323 1323  AT+CHS: Get or Set Frequency (Unit: Hz) for Single Channel Mode
1526 +)))
1324 1324  
1528 +(((
1325 1325  AT+CHE: Get or Set eight channels mode, Only for US915, AU915, CN470
1530 +)))
1326 1326  
1532 +(((
1327 1327  AT+CFG: Print all settings
1534 +)))
1328 1328  
1536 +== 4.2 Common AT Command Sequence ==
1329 1329  
1538 +=== 4.2.1 Multi-channel ABP mode (Use with SX1301/LG308) ===
1330 1330  
1331 -1.
1332 -11. Common AT Command Sequence
1333 -111. Multi-channel ABP mode (Use with SX1301/LG308)
1334 -
1540 +(((
1335 1335  If device has not joined network yet:
1542 +)))
1336 1336  
1337 -123456
1544 +(((
1545 +(% style="background-color:#dcdcdc" %)123456
1546 +)))
1338 1338  
1339 -AT+FDR
1548 +(((
1549 +(% style="background-color:#dcdcdc" %)AT+FDR
1550 +)))
1340 1340  
1341 -123456
1552 +(((
1553 +(% style="background-color:#dcdcdc" %)123456
1554 +)))
1342 1342  
1343 -AT+NJM=0
1556 +(((
1557 +(% style="background-color:#dcdcdc" %)AT+NJM=0
1558 +)))
1344 1344  
1345 -ATZ
1560 +(((
1561 +(% style="background-color:#dcdcdc" %)ATZ
1562 +)))
1346 1346  
1347 1347  
1565 +(((
1348 1348  If device already joined network:
1567 +)))
1349 1349  
1350 -AT+NJM=0
1569 +(((
1570 +(% style="background-color:#dcdcdc" %)AT+NJM=0
1571 +)))
1351 1351  
1352 -ATZ
1573 +(((
1574 +(% style="background-color:#dcdcdc" %)ATZ
1575 +)))
1353 1353  
1354 -1.
1355 -11.
1356 -111. Single-channel ABP mode (Use with LG01/LG02)
1577 +=== 4.2.2 Single-channel ABP mode (Use with LG01/LG02) ===
1357 1357  
1358 -123456   Enter Password to have AT access.
1579 +(((
1580 +(% style="background-color:#dcdcdc" %) 123456(%%)   Enter Password to have AT access.
1581 +)))
1359 1359  
1360 -AT+FDR   Reset Parameters to Factory Default, Keys Reserve
1583 +(((
1584 +(% style="background-color:#dcdcdc" %) AT+FDR(%%)   Reset Parameters to Factory Default, Keys Reserve
1585 +)))
1361 1361  
1362 -123456   Enter Password to have AT access.
1587 +(((
1588 +(% style="background-color:#dcdcdc" %) 123456(%%)   Enter Password to have AT access.
1589 +)))
1363 1363  
1364 -AT+CLASS=C Set to work in CLASS C
1591 +(((
1592 +(% style="background-color:#dcdcdc" %) AT+CLASS=C(%%) Set to work in CLASS C
1593 +)))
1365 1365  
1366 -AT+NJM=0 Set to ABP mode
1595 +(((
1596 +(% style="background-color:#dcdcdc" %) AT+NJM=0(%%) Set to ABP mode
1597 +)))
1367 1367  
1368 -AT+ADR=0 Set the Adaptive Data Rate Off
1599 +(((
1600 +(% style="background-color:#dcdcdc" %) AT+ADR=0(%%) Set the Adaptive Data Rate Off
1601 +)))
1369 1369  
1370 -AT+DR=5  Set Data Rate
1603 +(((
1604 +(% style="background-color:#dcdcdc" %) AT+DR=5(%%)  Set Data Rate
1605 +)))
1371 1371  
1372 -AT+TDC=60000  Set transmit interval to 60 seconds
1607 +(((
1608 +(% style="background-color:#dcdcdc" %) AT+TDC=60000(%%)  Set transmit interval to 60 seconds
1609 +)))
1373 1373  
1374 -AT+CHS=868400000 Set transmit frequency to 868.4Mhz
1611 +(((
1612 +(% style="background-color:#dcdcdc" %) AT+CHS=868400000(%%) Set transmit frequency to 868.4Mhz
1613 +)))
1375 1375  
1376 -AT+RX2FQ=868400000 Set RX2Frequency to 868.4Mhz (according to the result from server)
1615 +(((
1616 +(% style="background-color:#dcdcdc" %) AT+RX2FQ=868400000(%%) Set RX2Frequency to 868.4Mhz (according to the result from server)
1617 +)))
1377 1377  
1378 -AT+RX2DR=5  Set RX2DR to match the downlink DR from server. see below
1619 +(((
1620 +(% style="background-color:#dcdcdc" %) AT+RX2DR=5(%%)  Set RX2DR to match the downlink DR from server. see below
1621 +)))
1379 1379  
1380 -AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1, this ID can be found in the LoRa Server portal.
1623 +(((
1624 +(% style="background-color:#dcdcdc" %) AT+DADDR=26 01 1A F1 (%%)Set Device Address to 26 01 1A F1, this ID can be found in the LoRa Server portal.
1625 +)))
1381 1381  
1382 -ATZ          Reset MCU
1627 +(((
1628 +(% style="background-color:#dcdcdc" %) ATZ         (%%) Reset MCU
1629 +)))
1383 1383  
1384 -**Note:**
1631 +(((
1632 +(% style="color:red" %)**Note:**
1633 +)))
1385 1385  
1386 -1. Make sure the device is set to ABP mode in the IoT Server.
1387 -1. Make sure the LG01/02 gateway RX frequency is exactly the same as AT+CHS setting.
1388 -1. Make sure SF / bandwidth setting in LG01/LG02 match the settings of AT+DR. refer [[this link>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/&file=LoRaWAN%201.0.3%20Regional%20Parameters.xlsx]] to see what DR means.
1389 -1. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5
1635 +(((
1636 +(% style="color:red" %)1. Make sure the device is set to ABP mode in the IoT Server.
1637 +2. Make sure the LG01/02 gateway RX frequency is exactly the same as AT+CHS setting.
1638 +3. Make sure SF / bandwidth setting in LG01/LG02 match the settings of AT+DR. refer [[this link>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/&file=LoRaWAN%201.0.3%20Regional%20Parameters.xlsx]] to see what DR means.
1639 +4. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5
1640 +)))
1390 1390  
1391 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]]
1642 +(((
1643 +[[image:1653359097980-169.png||height="188" width="729"]]
1644 +)))
1392 1392  
1646 +(((
1647 +
1648 +)))
1393 1393  
1394 -1.
1395 -11.
1396 -111. Change to Class A
1650 +=== 4.2.3 Change to Class A ===
1397 1397  
1398 1398  If sensor JOINED
1399 -
1400 -AT+CLASS=A
1401 -
1653 +(% style="background-color:#dcdcdc" %)AT+CLASS=A
1402 1402  ATZ
1403 1403  
1656 += 5. FAQ =
1404 1404  
1658 +== 5.1 How to upgrade the image? ==
1405 1405  
1406 -
1407 -
1408 -1. FAQ
1409 -
1410 -1.
1411 -11. How to upgrade the image?
1412 -
1413 1413  The LT LoRaWAN Controller is shipped with a 3.5mm cable, the cable is used to upload image to LT to:
1414 1414  
1415 1415  * Support new features
1416 1416  * For bug fix
1417 1417  * Change LoRaWAN bands.
1418 -
1419 1419  Below shows the hardware connection for how to upload an image to the LT:
1666 +* [[image:1653359603330-121.png]]
1420 1420  
1421 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]
1422 -
1423 -
1668 +(((
1424 1424  **Step1:** Download [[flash loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].
1425 -
1426 1426  **Step2**: Download the [[LT Image files>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/image/]].
1427 -
1428 1428  **Step3: **Open flashloader; choose the correct COM port to update.
1429 -
1430 -**For LT-33222-L**:
1431 -
1432 -Hold down the PRO button and then momentarily press the RST reset button and the **DO2 led** will change from OFF to ON. When **DO2 LED** is on, it means the device is in download mode.
1433 -
1434 1434  **For LT-22222-L**:
1435 -
1436 1436  Hold down the PRO button and then momentarily press the RST reset button and the **DO1 led** will change from OFF to ON. When **DO1 LED** is on, it means the device is in download mode.
1437 -
1438 -
1439 -
1440 -|(((
1441 -Board detected
1442 1442  )))
1443 1443  
1444 -|(((
1445 -
1446 -)))
1676 + [[image:image-20220524103407-12.png]]
1447 1447  
1448 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]]
1678 +[[image:image-20220524103429-13.png]]
1449 1449  
1680 +[[image:image-20220524104033-15.png]]
1450 1450  
1682 +(% style="color:red" %)**Notice**(%%): In case user has lost the program cable. User can hand made one from a 3.5mm cable. The pin mapping is:
1451 1451  
1452 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]]
1684 +[[image:1653360054704-518.png||height="186" width="745"]]
1453 1453  
1686 +(((
1687 +(((
1688 +== 5.2 How to change the LoRa Frequency Bands/Region? ==
1689 +)))
1690 +)))
1454 1454  
1455 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image037.png]]
1692 +(((
1693 +User can follow the introduction for [[how to upgrade image>>||anchor="H5.1Howtoupgradetheimage3F"]]. When download the images, choose the required image file for download.
1694 +)))
1456 1456  
1696 +(((
1697 +== 5.3 How to set up LT to work with Single Channel Gateway such as LG01/LG02? ==
1698 +)))
1457 1457  
1458 -**Notice**: In case user has lost the program cable. User can hand made one from a 3.5mm cable. The pin mapping is:
1459 -
1460 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image038.png]]
1461 -
1462 -
1463 -1.
1464 -11. How to change the LoRa Frequency Bands/Region?
1465 -
1466 -User can follow the introduction for [[how to upgrade image>>path:#upgrade_image]]. When download the images, choose the required image file for download.
1467 -
1468 -
1469 -1.
1470 -11. How to set up LT to work with Single Channel Gateway such as LG01/LG02?
1471 -
1700 +(((
1701 +(((
1472 1472  In this case, users need to set LT-33222-L to work in ABP mode & transmit in only one frequency.
1703 +)))
1704 +)))
1473 1473  
1706 +(((
1707 +(((
1474 1474  Assume we have a LG02 working in the frequency 868400000 now , below is the step.
1709 +)))
1710 +)))
1475 1475  
1712 +(((
1713 +(% style="color:#4f81bd" %)**Step1**(%%): Log in TTN, Create an ABP device in the application and input the network session key (NETSKEY), app session key (APPSKEY) from the device.
1714 +)))
1476 1476  
1477 -**Step1**: Log in TTN, Create an ABP device in the application and input the network session key (NETSKEY), app session key (APPSKEY) from the device.
1716 +(((
1717 +[[image:1653360231087-571.png||height="401" width="727"]]
1718 +)))
1478 1478  
1479 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image039.png]]
1720 +(((
1721 +(% style="color:red" %)Note: user just need to make sure above three keys match, User can change either in TTN or Device to make then match. In TTN, NETSKEY and APPSKEY can be configured by user in setting page, but Device Addr is generated by TTN.
1722 +)))
1480 1480  
1481 -Note: user just need to make sure above three keys match, User can change either in TTN or Device to make then match. In TTN, NETSKEY and APPSKEY can be configured by user in setting page, but Device Addr is generated by TTN.
1724 +(((
1725 +(% style="color:#4f81bd" %)**Step2**(%%)**: **Run AT Command to make LT work in Single frequency & ABP mode. Below is the AT commands:
1726 +)))
1482 1482  
1728 +(((
1729 +(% style="background-color:#dcdcdc" %)123456 (%%) Enter Password to have AT access.
1730 +(% style="background-color:#dcdcdc" %)AT+FDR  (%%) Reset Parameters to Factory Default, Keys Reserve
1731 +(% style="background-color:#dcdcdc" %)123456  (%%) Enter Password to have AT access.
1732 +(% style="background-color:#dcdcdc" %)AT+NJM=0 (%%)Set to ABP mode
1733 +(% style="background-color:#dcdcdc" %)AT+ADR=0 (%%)Set the Adaptive Data Rate Off
1734 +(% style="background-color:#dcdcdc" %)AT+DR=5 (%%) Set Data Rate (Set AT+DR=3 for 915 band)
1735 +(% style="background-color:#dcdcdc" %)AT+TDC=60000  (%%)Set transmit interval to 60 seconds
1736 +(% style="background-color:#dcdcdc" %)AT+CHS=868400000 (%%)Set transmit frequency to 868.4Mhz
1737 +(% style="background-color:#dcdcdc" %)AT+DADDR=26 01 1A F1(%%) Set Device Address to 26 01 1A F1
1738 +(% style="background-color:#dcdcdc" %)ATZ                (%%)Reset MCU
1739 +)))
1483 1483  
1484 -**Step2: **Run AT Command to make LT work in Single frequency & ABP mode. Below is the AT commands:
1741 +(((
1742 +As shown in below:
1743 +)))
1485 1485  
1486 -123456   Enter Password to have AT access.
1745 +[[image:1653360498588-932.png||height="485" width="726"]]
1487 1487  
1488 -AT+FDR   Reset Parameters to Factory Default, Keys Reserve
1747 +== 5.4 Can I see counting event in Serial? ==
1489 1489  
1490 -123456   Enter Password to have AT access.
1749 +(((
1750 +User can run AT+DEBUG command to see the counting event in serial. If firmware too old and doesn’t support AT+DEBUG. User can update to latest firmware first.
1751 +)))
1491 1491  
1492 -AT+NJM=0 Set to ABP mode
1753 +(((
1754 += 6. Trouble Shooting =
1755 +)))
1493 1493  
1494 -AT+ADR=0 Set the Adaptive Data Rate Off
1757 +(((
1758 +(((
1759 +== 6.1 Downlink doesn’t work, how to solve it? ==
1760 +)))
1761 +)))
1495 1495  
1496 -AT+DR=5  Set Data Rate (Set AT+DR=3 for 915 band)
1763 +(((
1764 +Please see this link for how to debug: [[How it work>>LoRaWAN_Communication_Debug]]
1497 1497  
1498 -AT+TDC=60000  Set transmit interval to 60 seconds
1499 1499  
1500 -AT+CHS=868400000 Set transmit frequency to 868.4Mhz
1767 +[[http:~~/~~/wiki1.dragino.com/xwiki/bin/view/Main/LoRaWAN%20Communication%20Debug/#H5.1Howitwork>>http://wiki1.dragino.com/xwiki/bin/view/Main/LoRaWAN%20Communication%20Debug/#H5.1Howitwork]]
1501 1501  
1502 -AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1
1769 +
1770 +)))
1503 1503  
1504 -ATZ                Reset MCU
1772 +(((
1773 +== 6.2 Have trouble to upload image. ==
1774 +)))
1505 1505  
1506 -As shown in below:
1776 +(((
1777 +See this link for trouble shooting:
1507 1507  
1508 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image040.png]]
1779 +[[http:~~/~~/wiki1.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/>>http://wiki1.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/]]
1780 +)))
1509 1509  
1782 +(((
1783 +
1784 +)))
1510 1510  
1786 +(((
1787 +== 6.3 Why I can’t join TTN in US915 /AU915 bands? ==
1788 +)))
1511 1511  
1512 -1.
1513 -11. Can I see counting event in Serial?
1790 +(((
1791 +It might be about the channels mapping. Please see this link for detail:
1514 1514  
1515 -User can run AT+DEBUG command to see the counting event in serial. If firmware too old and doesn’t support AT+DEBUG. User can update to latest firmware first.
1793 +[[http:~~/~~/wiki1.dragino.com/xwiki/bin/view/Main/LoRaWAN%20Communication%20Debug/#H2.NoticeofUS9152FCN4702FAU915Frequencyband>>http://wiki1.dragino.com/xwiki/bin/view/Main/LoRaWAN%20Communication%20Debug/#H2.NoticeofUS9152FCN4702FAU915Frequencyband]]
1794 +)))
1516 1516  
1796 +(((
1797 +
1798 +)))
1517 1517  
1800 +(((
1801 += 7. Order Info =
1802 +)))
1518 1518  
1804 +(((
1805 +(((
1806 +(% style="color:#4f81bd" %)**LT-22222-L-XXX:**
1807 +)))
1808 +)))
1519 1519  
1520 -1. Trouble Shooting     
1521 -11. Downlink doesn’t work, how to solve it?
1810 +(((
1811 +(((
1812 +(% style="color:#4f81bd" %)**XXX:**
1813 +)))
1814 +)))
1522 1522  
1523 -Please see this link for how to debug:
1816 +(((
1817 +* (((
1818 +(% style="color:#4f81bd" %)**EU433**(%%): LT with frequency bands EU433
1819 +)))
1820 +)))
1524 1524  
1525 -[[http:~~/~~/wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#How_it_work>>url:http://wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#How_it_work]]
1822 +(((
1823 +* (((
1824 +(% style="color:#4f81bd" %)**EU868**(%%): LT with frequency bands EU868
1825 +)))
1826 +)))
1526 1526  
1828 +(((
1829 +* (((
1830 +(% style="color:#4f81bd" %)**KR920**(%%): LT with frequency bands KR920
1831 +)))
1832 +)))
1527 1527  
1528 -1.
1529 -11. Have trouble to upload image.
1834 +(((
1835 +* (((
1836 +(% style="color:#4f81bd" %)**CN470**(%%): LT with frequency bands CN470
1837 +)))
1838 +)))
1530 1530  
1531 -See this link for trouble shooting:
1840 +(((
1841 +* (((
1842 +(% style="color:#4f81bd" %)**AS923**(%%): LT with frequency bands AS923
1843 +)))
1844 +)))
1532 1532  
1533 -[[http:~~/~~/wiki.dragino.com/index.php?title=Firmware_Upgrade_Trouble_Shooting#UART_upgrade_trouble_shooting>>url:http://wiki.dragino.com/index.php?title=Firmware_Upgrade_Trouble_Shooting#UART_upgrade_trouble_shooting]]
1846 +(((
1847 +* (((
1848 +(% style="color:#4f81bd" %)**AU915**(%%): LT with frequency bands AU915
1849 +)))
1850 +)))
1534 1534  
1852 +(((
1853 +* (((
1854 +(% style="color:#4f81bd" %)**US915**(%%): LT with frequency bands US915
1855 +)))
1856 +)))
1535 1535  
1536 -1.
1537 -11. Why I can’t join TTN in US915 /AU915 bands?
1858 +(((
1859 +* (((
1860 +(% style="color:#4f81bd" %)**IN865**(%%): LT with frequency bands IN865
1861 +)))
1862 +)))
1538 1538  
1539 -It might be about the channels mapping. Please see this link for detail:
1864 +(((
1865 +* (((
1866 +(% style="color:#4f81bd" %)**CN779**(%%): LT with frequency bands CN779
1867 +)))
1540 1540  
1541 -[[http:~~/~~/wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band>>url:http://wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band]]
1869 += 8. Packing Info =
1870 +)))
1542 1542  
1543 -
1544 -
1545 -
1546 -1. Order Info
1547 -
1548 -**For LT-33222-L-XXX or LT-22222-L-XXX:**
1549 -
1550 -**XXX:**
1551 -
1552 -* **EU433**: LT with frequency bands EU433
1553 -* **EU868**: LT with frequency bands EU868
1554 -* **KR920**: LT with frequency bands KR920
1555 -* **CN470**: LT with frequency bands CN470
1556 -* **AS923**: LT with frequency bands AS923
1557 -* **AU915**: LT with frequency bands AU915
1558 -* **US915**: LT with frequency bands US915
1559 -* **IN865**: LT with frequency bands IN865
1560 -* **CN779**: LT with frequency bands CN779
1561 -
1562 -1. Packing Info
1563 -
1872 +(((
1873 +(((
1564 1564  **Package Includes**:
1875 +)))
1876 +)))
1565 1565  
1566 -* LT I/O Controller x 1
1878 +(((
1879 +(((
1880 +* LT-22222-L I/O Controller x 1
1567 1567  * Stick Antenna for LoRa RF part x 1
1568 1568  * Bracket for controller x1
1569 1569  * Program cable x 1
1884 +)))
1885 +)))
1570 1570  
1887 +(((
1888 +(((
1571 1571  **Dimension and weight**:
1890 +)))
1891 +)))
1572 1572  
1893 +(((
1894 +(((
1573 1573  * Device Size: 13.5 x 7 x 3 cm
1574 1574  * Device Weight: 105g
1575 1575  * Package Size / pcs : 14.5 x 8 x 5 cm
1576 1576  * Weight / pcs : 170g
1899 +)))
1900 +)))
1577 1577  
1578 -1. Support
1902 +(((
1903 += 9. Support =
1904 +)))
1579 1579  
1580 -* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
1581 -* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to
1906 +* (((
1907 +(((
1908 +Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
1909 +)))
1910 +)))
1911 +* (((
1912 +(((
1913 +Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to
1914 +)))
1915 +)))
1582 1582  
1583 -[[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]
1917 +(((
1918 +(((
1919 + [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]
1920 +)))
1921 +
1922 +(((
1923 += 10. Reference​​​​​ =
1924 +
1925 +* Product Page:
1926 +
1927 +LT-22222-L: [[http:~~/~~/www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html]]
1928 +
1929 +* [[Image Download>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/image/]]
1930 +* [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/]]
1931 +* [[Hardware Source>>url:https://github.com/dragino/Lora/tree/master/LT/LT-33222-L/v1.0]]
1932 +)))
1933 +)))
1653358238933-385.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +412.4 KB
Content
1653358355238-883.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +120.4 KB
Content
1653359097980-169.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +158.9 KB
Content
1653359603330-121.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +598.0 KB
Content
1653360054704-518.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +84.7 KB
Content
1653360231087-571.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +94.8 KB
Content
1653360498588-932.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +93.9 KB
Content
image-20220524103407-12.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +66.5 KB
Content
image-20220524103429-13.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +127.2 KB
Content
image-20220524103652-14.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +88.6 KB
Content
image-20220524104033-15.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +83.7 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0