Skip to Content
Last modified by Mengting Qiu on 2025/06/04 18:42
From version 249.1
edited by Mengting Qiu
on 2025/05/23 16:52
Change comment: There is no comment for this version
To version 243.11
edited by Xiaoling
on 2025/03/20 15:55
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.ting
1 +XWiki.Xiaoling
Content
... ... @@ -1511,9 +1511,9 @@
1511 1511  |(% style="width:113px" %)**Parameters**|(% style="width:384px" %)(((
1512 1512  **RO1_status** : 1 byte in hex
1513 1513  
1514 -00: Open
1514 +00: Close
1515 1515  
1516 -01: Close
1516 +01: Open
1517 1517  
1518 1518  11: No action
1519 1519  
... ... @@ -1520,9 +1520,9 @@
1520 1520  
1521 1521  **RO2_status** : 1 byte in hex
1522 1522  
1523 -00: Open
1523 +00: Close
1524 1524  
1525 -01: Close
1525 +01: Open
1526 1526  
1527 1527  11: No action
1528 1528  )))
... ... @@ -1542,6 +1542,7 @@
1542 1542  (% style="color:red" %)**The device will transmit an uplink packet if the downlink payload is executed successfully.**
1543 1543  )))
1544 1544  
1545 +
1545 1545  ==== 3.4.2.15 Relay ~-~- Control Relay Output RO1/RO2 with time control ====
1546 1546  
1547 1547  
... ... @@ -1673,6 +1673,7 @@
1673 1673  If AVI1 voltage higher than VOLMAX (20000mV =20v), counter increase 1
1674 1674  )))
1675 1675  
1677 +
1676 1676  ==== 3.4.2.17 Counting ~-~- Pre-configure the Count Number ====
1677 1677  
1678 1678  
... ... @@ -1723,6 +1723,7 @@
1723 1723  Sets the COUNT1 to 10.
1724 1724  )))
1725 1725  
1728 +
1726 1726  ==== 3.4.2.18 Counting ~-~- Clear Counting ====
1727 1727  
1728 1728  
... ... @@ -1745,12 +1745,11 @@
1745 1745  )))
1746 1746  |(% style="width:141px" %)**Example**|(% style="width:357px" %)A6 **01**
1747 1747  
1748 -==== 3.4.2.19 Set the save intervals of the counting results, RO (Relay Output), and DO (Digital Output) states ====
1751 +==== 3.4.2.19 Counting ~-~- Set Saving Interval for 'Counting Result' ====
1749 1749  
1750 -This command configures the device to periodically save the counting results, RO (Relay Output), and DO (Digital Output) states to internal flash memory at a user-defined interval. By setting a save interval, the device ensures that critical data (counting values and output states) is preserved in case of power loss.
1751 -The save interval can be adjusted to the user's needs, with a minimum value of (% style="color:blue" %)**30**(%%) seconds.
1752 -The saved RO/DO states can be restored after a device reset by combining this function with the (% style="color:blue" %)**AT+RODORESET**(%%) command.
1753 1753  
1754 +This command allows you to configure the device to save its counting result to internal flash memory at specified intervals. By setting a save time, the device will periodically store the counting data to prevent loss in case of power failure. The save interval can be adjusted to suit your requirements, with a minimum value of 30 seconds.
1755 +
1754 1754  (% style="color:#037691" %)**AT Command**
1755 1755  
1756 1756  (% border="2" style="width:500px" %)
... ... @@ -1760,7 +1760,7 @@
1760 1760  |(% style="width:124px" %)**Example**|(% style="width:374px" %)(((
1761 1761  AT+COUTIME=60
1762 1762  
1763 -Sets the device to save its counting results, RO and DO states to the memory every 60 seconds.
1765 +Sets the device to save its counting results to the memory every 60 seconds.
1764 1764  )))
1765 1765  
1766 1766  (% style="color:#037691" %)**Downlink Payload**
... ... @@ -1775,7 +1775,7 @@
1775 1775  |(% style="width:123px" %)**Example**|(% style="width:375px" %)(((
1776 1776  A7 **00 00 3C**
1777 1777  
1778 -SSets the device to save its counting results, RO and DO states to the memory every 60 seconds.
1780 +Sets the device to save its counting results to the memory every 60 seconds.
1779 1779  )))
1780 1780  
1781 1781  ==== 3.4.2.20 Reset saved RO and DO states ====