Last modified by Saxer Lin on 2025/04/15 17:24
<
From version < 178.1 >
edited by Dilisi S
on 2024/11/09 02:59
To version < 165.1 >
edited by Dilisi S
on 2024/11/06 22:47
>
Change comment: some minor edits on 6th nov. as part 1

Summary

Details

Page properties
Content
... ... @@ -33,6 +33,8 @@
33 33  With the LT-22222-L I/O Controller, users can transmit data over ultra-long distances with low power consumption using LoRa, a spread-spectrum modulation technique derived from chirp spread spectrum (CSS) technology that operates on license-free ISM bands.
34 34  )))
35 35  
36 +> The LT Series I/O Controllers are designed for easy, low-cost installation on LoRaWAN networks.
37 +
36 36  (((
37 37  You can connect the LT-22222-L I/O Controller to a LoRaWAN network service provider in several ways:
38 38  
... ... @@ -57,7 +57,7 @@
57 57  * SX1276/78 Wireless Chip 
58 58  * Power Consumption:
59 59  ** Idle: 4mA@12v
60 -** 20dB Transmit: 34mA@12V
62 +** 20dB Transmit: 34mA@12v
61 61  * Operating Temperature: -40 ~~ 85 Degrees, No Dew
62 62  
63 63  (% style="color:#037691" %)**Interface for Model: LT22222-L:**
... ... @@ -66,7 +66,7 @@
66 66  * 2 x Digital Output (NPN output. Max pull-up voltage 36V,450mA)
67 67  * 2 x Relay Output (5A@250VAC / 30VDC)
68 68  * 2 x 0~~20mA Analog Input (res:0.01mA)
69 -* 2 x 0~~30V Analog Input (res:0.01V)
71 +* 2 x 0~~30V Analog Input (res:0.01v)
70 70  * Power Input 7~~ 24V DC. 
71 71  
72 72  (% style="color:#037691" %)**LoRa Spec:**
... ... @@ -134,10 +134,10 @@
134 134  
135 135  * 1 x LT-22222-L I/O Controller
136 136  * 1 x LoRaWAN antenna matched to the frequency of the LT-22222-L
137 -* 1 x bracket for DIN rail mounting
139 +* 1 x bracket for wall mounting
138 138  * 1 x programming cable
139 139  
140 -Attach the LoRaWAN antenna to the antenna connector, **ANT**,** **located on the top right side of the device, next to the upper terminal block. Secure the antenna by tightening it clockwise.
142 +Attach the LoRaWAN antenna to the antenna connector, ANT,** **located on the top right side of the device, next to the upper terminal block. Secure the antenna by tightening it clockwise.
141 141  
142 142  == 2.2 Terminals ==
143 143  
... ... @@ -169,7 +169,7 @@
169 169  
170 170  == 2.3 Powering the LT-22222-L ==
171 171  
172 -The LT-22222-L I/O Controller can be powered by a **7–24V DC** power source. Connect the power supply’s positive wire to the VIN and the negative wire to the GND screw terminals. The power indicator (PWR) LED will turn on when the device is properly powered.
174 +The LT-22222-L I/O Controller can be powered by a 7–24V DC power source. Connect the power supply’s positive wire to the VIN and the negative wire to the GND screw terminals. The power indicator (PWR) LED will turn on when the device is properly powered.
173 173  
174 174  
175 175  [[image:1653297104069-180.png]]
... ... @@ -181,13 +181,13 @@
181 181  
182 182  By default, the LT-22222-L is configured to operate in LoRaWAN Class C mode. It supports OTAA (Over-the-Air Activation), the most secure method for activating a device with a LoRaWAN network server. The LT-22222-L comes with device registration information that allows you to register it with a LoRaWAN network, enabling the device to perform OTAA activation with the network server upon initial power-up and after any subsequent reboots.
183 183  
184 -After powering on, the **TX LED** will **fast-blink 5 times** which means the LT-22222-L will enter the **work mode** and start to **join** the LoRaWAN network. The **TX LED** will be on for **5 seconds** after joining the network. When there is a **downlink** message from the server, the **RX LE**D will be on for **1 second**. When the device is sending an uplink message to the server, the **TX LED** will be on for **1 second**. See also LED status.
186 +For LT-22222-L, the LED will show the Join status: After powering on, the TX LED will fast-blink 5 times which means the LT-22222-L will enter the working mode and start to JOIN the LoRaWAN network. The TX LED will be on for 5 seconds after joining the network. When there is a message from the server, the RX LED will be on for 1 second. 
185 185  
186 186  In case you can't set the root key and other identifiers in the network server and must use them from the server, you can use [[AT Commands>>||anchor="H4.UseATCommand"]] to configure them on the device.
187 187  
188 188  == 3.2 Registering with a LoRaWAN network server ==
189 189  
190 -The network diagram below shows how the LT-22222-L is connected to a typical LoRaWAN network.
192 +The diagram below shows how the LT-22222-L connects to a typical LoRaWAN network.
191 191  
192 192  [[image:image-20220523172350-1.png||height="266" width="864"]]
193 193  
... ... @@ -205,11 +205,8 @@
205 205  * Create an application if you do not have one yet.
206 206  * Register LT-22222-L with that application. Two registration options are available:
207 207  
208 -(% class="wikigeneratedid" %)
209 -==== ====
210 +==== Using the LoRaWAN Device Repository: ====
210 210  
211 -==== 3.2.2.1 Using the LoRaWAN Device Repository ====
212 -
213 213  * Go to your application and click on the **Register end device** button.
214 214  * On the **Register end device** page:
215 215  ** Select the option **Select the end device in the LoRaWAN Device Repository**.
... ... @@ -218,8 +218,7 @@
218 218  
219 219  [[image:lt-22222-l-dev-repo-reg-p1.png||height="625" width="1000"]]
220 220  
221 -
222 -* Page continued...
220 +*
223 223  ** Enter the **AppEUI** in the **JoinEUI** field and click the **Confirm** button.
224 224  ** Enter the **DevEUI** in the **DevEUI** field.
225 225  ** Enter the **AppKey** in the **AppKey** field.
... ... @@ -228,11 +228,8 @@
228 228  
229 229  [[image:lt-22222-l-dev-repo-reg-p2.png||height="625" width="1000"]]
230 230  
231 -(% class="wikigeneratedid" %)
232 -==== ====
229 +==== Entering device information manually: ====
233 233  
234 -==== 3.2.2.2 Entering device information manually ====
235 -
236 236  * On the **Register end device** page:
237 237  ** Select the **Enter end device specifies manually** option as the input method.
238 238  ** Select the **Frequency plan** that matches your device.
... ... @@ -245,52 +245,29 @@
245 245  [[image:lt-22222-l-manually-p1.png||height="625" width="1000"]]
246 246  
247 247  
248 -* Page continued...
249 -** Enter **AppEUI** in the **JoinEUI** field and click the **Confirm** button.
250 -** Enter **DevEUI** in the **DevEUI** field.
251 -** Enter **AppKey** in the **AppKey** field.
252 -** In the **End device ID** field, enter a unique name within this application for your LT-22222-N.
253 -** Under **After registration**, select the **View registered end device** option.
254 -** Click the **Register end device** button.
243 +* Enter **AppEUI** in the **JoinEUI** field and click the **Confirm** button.
244 +* Enter **DevEUI** in the **DevEUI** field.
245 +* Enter **AppKey** in the **AppKey** field.
246 +* In the **End device ID** field, enter a unique name within this application for your LT-22222-N.
247 +* Under **After registration**, select the **View registered end device** option.
255 255  
256 256  [[image:lt-22222-l-manually-p2.png||height="625" width="1000"]]
257 257  
258 258  
259 -You will be navigated to the **Device overview** page.
252 +==== Joining ====
260 260  
254 +Click on **Live Data** in the left navigation. Then, power on the device, and it will join The Things Stack Sandbox. You can see the join request, join accept, followed by uplink messages form the device showing in the Live Data panel.
261 261  
262 -[[image:lt-22222-device-overview.png||height="625" width="1000"]]
256 +[[image:1653298044601-602.png||height="405" width="709"]]
263 263  
264 264  
265 -==== 3.2.2.3 Joining ====
259 +== 3.3 Uplink Payload formats ==
266 266  
267 -Click on **Live data** in the left navigation. The Live data panel for your application will display.
268 268  
269 -Power on your LT-22222-L. It will begin joining The Things Stack LoRaWAN network server. In the **Live data** panel, you can see the **join-request** and **join-accept** messages exchanged between the device and the network server. Once successfully joined, the device will send its first **uplink data message** to the application it belongs to (in this example, **dragino-docs**).
262 +The LT-22222-L has 5 working modes. It also has an interrupt/trigger mode for different types of applications that can be used together with any working mode as an additional feature. The default mode is MOD1 and you can switch between these modes using AT commands.
270 270  
264 +* (% style="color:blue" %)**MOD1**(%%): (default mode/factory set): 2 x ACI + 2AVI + DI + DO + RO
271 271  
272 -[[image:lt-22222-join-network.png||height="625" width="1000"]]
273 -
274 -
275 -By default, you will receive an uplink data message every 10 minutes.
276 -
277 -Click on one of a **Forward uplink data messages **to see its payload content. The payload content is encapsulated within the decode_payload {} JSON object.
278 -
279 -[[image:lt-22222-ul-payload-decoded.png]]
280 -
281 -
282 -If you can't see the decoded payload, it is because you haven't added the uplink formatter code. To add the uplink formatter code, select **End devices** > **LT-22222-L** > **Payload formatters** > **Uplink**. Then  select **Use Device repository formatters** for the **Formatter type** dropdown. Click the **Save changes** button to apply the changes.
283 -
284 -[[image:lt-22222-ul-payload-fmt.png||height="686" width="1000"]]
285 -
286 -
287 -== 3.3 Work Modes and their Uplink Payload formats ==
288 -
289 -
290 -The LT-22222-L has 5 **work modes**. It also has an interrupt/trigger mode for different types of applications that can be used together with any work mode as an additional feature. The default mode is MOD1 and you can switch between these modes using AT commands.
291 -
292 -* (% style="color:blue" %)**MOD1**(%%): (default mode/factory set): 2ACI + 2AVI + DI + DO + RO
293 -
294 294  * (% style="color:blue" %)**MOD2**(%%): Double DI Counting + DO + RO
295 295  
296 296  * (% style="color:blue" %)**MOD3**(%%): Single DI Counting + 2 x ACI + DO + RO
... ... @@ -301,16 +301,12 @@
301 301  
302 302  * (% style="color:blue" %)**ADDMOD6**(%%): Trigger Mode, Optional, used together with MOD1 ~~ MOD5
303 303  
304 -
305 -The uplink messages are sent over LoRaWAN FPort 2. By default, an uplink message is sent every 10 minutes.
306 -
307 307  === 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
308 308  
278 +
309 309  (((
310 -This is the default mode.
280 +The uplink payload is 11 bytes long. Uplink packets are sent over LoRaWAN FPort=2. By default, one uplink is sent every 10 minutes. (% style="display:none" wfd-invisible="true" %)
311 311  
312 -The uplink payload is 11 bytes long. (% style="display:none" wfd-invisible="true" %)
313 -
314 314  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
315 315  |(% style="background-color:#4f81bd; color:white" %)**Size(bytes)**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**1**|(% style="background-color:#4f81bd; color:white" %)**1**|(% style="background-color:#4f81bd; color:white" %)**1**
316 316  |Value|(((
... ... @@ -321,13 +321,13 @@
321 321  ACI1 Current
322 322  )))|(((
323 323  ACI2 Current
324 -)))|**DIDORO***|(((
292 +)))|DIDORO*|(((
325 325  Reserve
326 326  )))|MOD
327 327  )))
328 328  
329 329  (((
330 -(% style="color:#4f81bd" %)*** DIDORO**(%%) is a combination of RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1, and its size is1 byte long as shown below.
298 +(% style="color:#4f81bd" %)*** DIDORO**(%%) is a combination of RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1, for a total of 1 byte, as shown below.
331 331  
332 332  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
333 333  |**bit 7**|**bit 6**|**bit 5**|**bit 4**|**bit 3**|**bit 2**|**bit 1**|**bit 0**
... ... @@ -334,9 +334,9 @@
334 334  |RO1|RO2|--DI3--|DI2|DI1|--DO3--|DO2|DO1
335 335  )))
336 336  
337 -* RO is for the relay. ROx=1: CLOSED, ROx=0 always OPEN.
338 -* DI is for digital input. DIx=1: HIGH or FLOATING, DIx=0: LOW.
339 -* DO is for reverse digital output. DOx=1: LOW, DOx=0: HIGH or FLOATING.
305 +* RO is for the relay. ROx=1: closed, ROx=0 always open.
306 +* DI is for digital input. DIx=1: high or floating, DIx=0: low.
307 +* DO is for reverse digital output. DOx=1: output low, DOx=0: high or floating.
340 340  
341 341  (% style="color:red" %)**Note: DI3 and DO3 bits are not valid for LT-22222-L**
342 342  
... ... @@ -357,13 +357,13 @@
357 357  
358 358  * [1] The RO1 relay channel is CLOSED, and the RO1 LED is ON.
359 359  * [0] The RO2 relay channel is OPEN, and the RO2 LED is OFF.
360 -* **[1] DI3 - not used for LT-22222-L.**
328 +* [1] DI3 - not used for LT-22222-L.
361 361  * [0] DI2 channel input is LOW, and the DI2 LED is OFF.
362 362  * [1] DI1 channel input state:
363 363  ** DI1 is FLOATING when no sensor is connected between DI1+ and DI1-.
364 364  ** DI1 is HIGH when a sensor is connected between DI1- and DI1+ and the sensor is ACTIVE.
365 365  ** DI1 LED is ON in both cases.
366 -* **[0] DO3 - not used for LT-22222-L.**
334 +* [0] DO3 - not used for LT-22222-L.
367 367  * [1] DO2 channel output is LOW, and the DO2 LED is ON.
368 368  * [0] DO1 channel output state:
369 369  ** DO1 is FLOATING when there is no load between DO1 and V+.
... ... @@ -374,7 +374,7 @@
374 374  
375 375  
376 376  (((
377 -**For LT-22222-L**: In this mode, **DI1 and DI2** are used as counting pins.
345 +**For LT-22222-L**: In this mode, the **DI1 and DI2** are used as counting pins.
378 378  )))
379 379  
380 380  (((
... ... @@ -388,17 +388,17 @@
388 388  )))
389 389  
390 390  (((
391 -(% style="color:#4f81bd" %)***DIDORO**(%%) is a combination of RO1, RO2, FIRST, Reserve, Reserve, DO3, DO2 and DO1, and its size is 1 byte long as shown below.
359 +(% style="color:#4f81bd" %)***DIDORO**(%%) is a combination of RO1, RO2, DO3, DO2 and DO1, for a total of 1 byte, as shown below.
392 392  
393 393  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
394 394  |**bit 7**|**bit 6**|**bit 5**|**bit 4**|**bit 3**|**bit 2**|**bit 1**|**bit 0**
395 395  |RO1|RO2|FIRST|Reserve|Reserve|--DO3--|DO2|DO1
396 396  
397 -* RO is for the relay. ROx=1: CLOSED, ROx=0 always OPEN.
365 +* RO is for the relay. ROx=1: closed, ROx=0 always open.
398 398  )))
399 399  
400 400  * FIRST: Indicates that this is the first packet after joining the network.
401 -* DO is for reverse digital output. DOx=1: LOW, DOx=0: HIGH or FLOATING.
369 +* DO is for reverse digital output. DOx=1: output low, DOx=0: high or floating.
402 402  
403 403  (((
404 404  (% style="color:red" %)**Note: DO3 bit is not valid for LT-22222-L**
... ... @@ -797,11 +797,11 @@
797 797  )))
798 798  
799 799  
800 -== 3.4 ​Configure LT via AT Commands or Downlinks ==
768 +== 3.4 ​Configure LT via AT or Downlink ==
801 801  
802 802  
803 803  (((
804 -User can configure LT I/O Controller via AT Commands or LoRaWAN Downlinks.
772 +User can configure LT I/O Controller via AT Commands or LoRaWAN Downlink Commands
805 805  )))
806 806  
807 807  (((
... ... @@ -816,8 +816,9 @@
816 816  
817 817  === 3.4.1 Common Commands ===
818 818  
787 +
819 819  (((
820 -These commands should be available for all Dragino sensors, such as changing the uplink interval or resetting the device. For firmware v1.5.4, you can find the supported common commands under [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]].
789 +They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
821 821  )))
822 822  
823 823  
... ... @@ -825,8 +825,9 @@
825 825  
826 826  ==== 3.4.2.1 Set Transmit Interval ====
827 827  
828 -Sets the uplink interval of the device. The default uplink transmission interval is 10 minutes.
829 829  
798 +Sets the uplink interval of the device.
799 +
830 830  * (% style="color:#037691" %)**AT command:**
831 831  
832 832  (% style="color:blue" %)**AT+TDC=N**
... ... @@ -1386,122 +1386,69 @@
1386 1386  
1387 1387  == 3.5 Integrating with ThingsEye.io ==
1388 1388  
1389 -The Things Stack applications can be integrated with ThingsEye.io. Once integrated, ThingsEye.io works as an MQTT client for The Things Stack MQTT broker, allowing it to subscribe to upstream traffic and publish downlink traffic.
1359 +If you are using one of The Things Stack plans, you can integrate ThingsEye.io with your application. Once integrated, ThingsEye.io works as an MQTT client for The Things Stack MQTT broker, allowing it to subscribe to upstream traffic and publish downlink traffic.
1390 1390  
1391 -=== 3.5.1 Configuring MQTT Connection Information with The Things Stack Sandbox ===
1361 +=== 3.5.1 Configuring The Things Stack Sandbox ===
1392 1392  
1393 -We use The Things Stack Sandbox for demonstating the configuration but  other
1363 +* Go to your Application and select MQTT under Integrations.
1364 +* In the Connection credentials section, under Username, The Thins Stack displays an auto-generated username. You can use it or provide a new one.
1365 +* For the Password, click the Generate new API key button to generate a password. You can see it by clicking on the eye button.
1394 1394  
1395 -* In **The Things Stack Sandbox**, select your application under **Applications**.
1396 -* Select **MQTT** under **Integrations**.
1397 -* In the **Connection information **section, for **Username**, The Things Stack displays an auto-generated username. You can use it or provide a new one.
1398 -* For the **Password**, click the **Generate new API key** button to generate a password. You can see it by clicking on the **eye** button. The API key works as the password.
1399 -
1400 -NOTE. The username and  password (API key) you created here are required in the next section.
1401 -
1402 1402  [[image:tts-mqtt-integration.png||height="625" width="1000"]]
1403 1403  
1404 1404  === 3.5.2 Configuring ThingsEye.io ===
1405 1405  
1406 -This section guides you on how to create an integration in ThingsEye to connect with The Things Stack MQTT server.
1371 +* Login to your thingsEye.io account.
1372 +* Under the Integrations center, click Integrations.
1373 +* Click the Add integration button (the button with the + symbol).
1407 1407  
1408 -* Login to your [[ThingsEye.io >>https://thingseye.io]]account.
1409 -* Under the **Integrations center**, click **Integrations**.
1410 -* Click the **Add integration** button (the button with the **+** symbol).
1411 -
1412 1412  [[image:thingseye-io-step-1.png||height="625" width="1000"]]
1413 1413  
1414 1414  
1415 -On the **Add integration** window, configure the following:
1378 +On the Add integration page configure the following:
1416 1416  
1417 -**Basic settings:**
1380 +Basic settings:
1418 1418  
1419 -* Select **The Things Stack Community** from the **Integration type** list.
1420 -* Enter a suitable name for your integration in the **Name **text** **box or keep the default name.
1421 -* Ensure the following options are turned on.
1422 -** Enable integration
1423 -** Debug mode
1424 -** Allow create devices or assets
1425 -* Click the **Next** button. you will be navigated to the **Uplink data converter** tab.
1382 +* Select The Things Stack Community from the Integration type list.
1383 +* Enter a suitable name for your integration in the Name box or keep the default name.
1384 +* Click the Next button.
1426 1426  
1427 1427  [[image:thingseye-io-step-2.png||height="625" width="1000"]]
1428 1428  
1388 +Uplink Data converter:
1429 1429  
1430 -**Uplink data converter:**
1390 +* Click the Create New button if it is not selected by default.
1391 +* Click the JavaScript button.
1392 +* Paste the uplink decoder function into the text area (first, delete the default code). The demo decoder function can be found here.
1393 +* Click the Next button.
1431 1431  
1432 -* Click the **Create new** button if it is not selected by default.
1433 -* Enter a suitable name for the uplink data converter in the **Name **text** **box or keep the default name.
1434 -* Click the **JavaScript** button.
1435 -* Paste the uplink decoder function into the text area (first, delete the default code). The demo uplink decoder function can be found [[here>>https://raw.githubusercontent.com/ThingsEye-io/te-platform/refs/heads/main/Data%20Converters/The_Things_Network_MQTT_Uplink_Converter.js]].
1436 -* Click the **Next** button. You will be navigated to the **Downlink data converter **tab.
1437 -
1438 1438  [[image:thingseye-io-step-3.png||height="625" width="1000"]]
1439 1439  
1397 +Downlink Data converter (this is an optional step):
1440 1440  
1441 -**Downlink data converter (this is an optional step):**
1399 +* Click the Create new button if it is not selected by default.
1400 +* Click the JavaScript button.
1401 +* Paste the downlink decoder function into the text area (first, delete the default code). The demo decoder function can be found here.
1402 +* Click the Next button.
1442 1442  
1443 -* Click the **Create new** button if it is not selected by default.
1444 -* Enter a suitable name for the downlink data converter in the **Name **text** **box or keep the default name
1445 -* Click the **JavaScript** button.
1446 -* Paste the downlink decoder function into the text area (first, delete the default code). The demo downlink decoder function can be found here.
1447 -* Click the **Next** button. You will be navigated to the **Connection** tab.
1448 -
1449 1449  [[image:thingseye-io-step-4.png||height="625" width="1000"]]
1450 1450  
1406 +Connection:
1451 1451  
1452 -**Connection:**
1408 +* Choose Region from the Host type.
1409 +* Enter the cluster of your The Things Stack in the Region textbox.
1410 +* Enter the Username and Password in the Credentials section. Use the same username and password you created with the MQTT page of The Things Stack.
1411 +* Click Check connection to test the connection. If the connection is successful, you can see the message saying Connected.
1412 +* Click the Add button.
1453 1453  
1454 -* Choose **Region** from the **Host type**.
1455 -* Enter the **cluster** of your **The Things Stack** in the **Region** textbox. You can find the cluster in the url (e.g., https:~/~/**eu1**.cloud.thethings.network/...).
1456 -* Enter the **Username** and **Password** of the MQTT integration in the **Credentials** section. The username and password can be found on the MQTT integration page of your The Things Stack account (see Configuring MQTT Connection information with The Things Stack Sandbox).
1457 -* Click the **Check connection** button to test the connection. If the connection is successful, you will see the message saying **Connected**.
1458 -
1459 -[[image:message-1.png]]
1460 -
1461 -
1462 -* Click the **Add** button.
1463 -
1464 1464  [[image:thingseye-io-step-5.png||height="625" width="1000"]]
1465 1465  
1466 1466  
1467 -Your integration has been added to the** Integrations** list and will be displayed on the **Integrations** page. Check whether the status is shown as **Active**. If not, review your configuration settings.
1417 +Your integration is added to the integrations list and it will display on the Integrations page.
1468 1468  
1419 +[[image:thingseye-io-step-6.png||height="625" width="1000"]]
1469 1469  
1470 -[[image:thingseye.io_integrationsCenter_integrations.png||height="686" width="1000"]]
1471 1471  
1472 -
1473 -**Viewing integration details**:
1474 -
1475 -Click on your integration from the list. The Integration details window will appear with the Details tab selected. The Details tab shows all the settings you have provided for this integration.
1476 -
1477 -[[image:integration-details.png||height="686" width="1000"]]
1478 -
1479 -
1480 -If you want to edit the settings you have provided, click on the **Toggle edit mode** button. Once you have done click on the **Apply changes **button.
1481 -
1482 -Note: See also ThingsEye documentation.
1483 -
1484 -
1485 -**Viewing events:**
1486 -
1487 -This tab  displays all the uplink messages from the LT-22222-L.
1488 -
1489 -* Click on the **Events **tab.
1490 -* Select **Debug **from the **Event type** dropdown.
1491 -* Select the** time frame** from the **time window**.
1492 -
1493 -[insert image]
1494 -
1495 -- To view the JSON payload of a message, click on the three dots (...) in the Message column of the desired message.
1496 -
1497 -[insert image]
1498 -
1499 -
1500 -**Deleting the integration**:
1501 -
1502 -If you want to delete this integration, click the **Delete integratio**n button.
1503 -
1504 -
1505 1505  == 3.6 Interface Details ==
1506 1506  
1507 1507  === 3.6.1 Digital Input Port: DI1/DI2 /DI3 ( For LT-33222-L, low active ) ===
... ... @@ -1757,7 +1757,7 @@
1757 1757  
1758 1758  
1759 1759  (((
1760 -On the PC, the user needs to set the (% style="color:#4f81bd" %)**serial tool **(%%)(such as [[PuTTY>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]] or [[SecureCRT>>https://www.vandyke.com/cgi-bin/releases.php?product=securecrt]]) to a baud rate of (% style="color:green" %)**9600**(%%) to access the serial console of LT-22222-L. The AT commands are disabled by default, and a password (default:(% style="color:green" %)**123456**)(%%) must be entered to active them, as shown below:
1677 +On the PC, the user needs to set the (% style="color:#4f81bd" %)**serial tool**(%%)(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) to a baud rate of (% style="color:green" %)**9600**(%%) to access to access serial console of LT-22222-L. The AT commands are disabled by default, and a password (default:(% style="color:green" %)**123456**)(%%) must be entered to active them, as shown below:
1761 1761  )))
1762 1762  
1763 1763  [[image:1653358355238-883.png]]
... ... @@ -2102,7 +2102,7 @@
2102 2102  
2103 2103  = 6. FAQ =
2104 2104  
2105 -== 6.1 How to upgrade the firmware image? ==
2022 +== 6.1 How to upgrade the image? ==
2106 2106  
2107 2107  
2108 2108  The LT-22222-L I/O Controller is shipped with a 3.5mm cable, which is used to upload an image to LT in order to:
... ... @@ -2111,25 +2111,20 @@
2111 2111  * Fix bugs.
2112 2112  * Change LoRaWAN bands.
2113 2113  
2114 -Below is the hardware connection setup for uploading an firmware image to the LT-22222-L:
2031 +Below is the hardware connection setup for uploading an image to the LT:
2115 2115  
2116 -(% class="box infomessage" %)
2117 -(((
2118 -The latest firmware version available for the LT-22222-L is v1.6.1 at the time of this writing.
2119 -)))
2120 -
2121 2121  [[image:1653359603330-121.png]]
2122 2122  
2123 2123  
2124 2124  (((
2125 -(% style="color:#0000ff" %)**Step 1**(%%)**:** Download the F[[lash Loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]]. (replaced by STM32CubeProgrammer)
2037 +(% style="color:#0000ff" %)**Step 1**(%%)**:** Download the F[[lash Loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].
2126 2126  (% style="color:#0000ff" %)**Step 2**(%%)**:** Download the [[LT Image files>>https://www.dropbox.com/sh/g99v0fxcltn9r1y/AACrbrDN0AqLHbBat0ViWx5Da/LT-22222-L/Firmware?dl=0&subfolder_nav_tracking=1]].
2127 2127  (% style="color:#0000ff" %)**Step 3**(%%)**:** Open the Flash Loader and choose the correct COM port to update.
2040 +
2128 2128  
2129 2129  (((
2130 2130  (% style="color:blue" %)**For LT-22222-L**(%%):
2131 -
2132 -Hold down the **PRO** button, then briefly press the **RST** button. The **DO1** LED will change from OFF to ON. When the **DO1** LED is ON, it indicates that the device is in firmware download mode.
2044 +Hold down the PRO button, then momentarily press the RST reset button. The (% style="color:red" %)**DO1 LED**(%%) will change from OFF to ON. When the (% style="color:red" %)**DO1 LED**(%%) is ON, it indicates that the device is in download mode.
2133 2133  )))
2134 2134  
2135 2135  
integration-details.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.pradeeka
Size
... ... @@ -1,1 +1,0 @@
1 -463.9 KB
Content
lt-22222-device-overview.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.pradeeka
Size
... ... @@ -1,1 +1,0 @@
1 -497.2 KB
Content
lt-22222-join-network.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.pradeeka
Size
... ... @@ -1,1 +1,0 @@
1 -340.6 KB
Content
lt-22222-ul-payload-decoded.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.pradeeka
Size
... ... @@ -1,1 +1,0 @@
1 -48.7 KB
Content
lt-22222-ul-payload-fmt.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.pradeeka
Size
... ... @@ -1,1 +1,0 @@
1 -438.6 KB
Content
message-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.pradeeka
Size
... ... @@ -1,1 +1,0 @@
1 -20.1 KB
Content
thingseye.io_integrationsCenter_integrations-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.pradeeka
Size
... ... @@ -1,1 +1,0 @@
1 -469.3 KB
Content
thingseye.io_integrationsCenter_integrations.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.pradeeka
Size
... ... @@ -1,1 +1,0 @@
1 -302.3 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0