Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Last modified by Saxer Lin on 2025/04/15 17:24

From version < 166.1 >

edited by Dilisi S
on 2024/11/07 05:43

To version < 154.1 >

edited by Dilisi S
on 2024/11/01 04:40

Change comment: Uploaded new attachment "lt-22222-l-manually-p2.png", version {1}

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Attachments (2 modified, 0 added, 0 removed)
- lt-22222-l-manually-p1.png
- lt-22222-l-manually-p2.png

Details

Page properties

Content

@@ -17,7 +17,7 @@
--= 1. Introduction =
++= 1.Introduction =
  == 1.1 What is the LT-22222-L I/O Controller? ==
@@ -42,7 +42,7 @@
  * If there is no public LoRaWAN coverage in your area, you can set up a LoRaWAN gateway, or multiple gateways, and connect them to a LoRaWAN network server to create adequate coverage. Then, register the LT-22222-L I/O controller with this network.
  * Setup your own private LoRaWAN network.
--> You can use a LoRaWAN gateway, such as the Dragino LG308, to expand or create LoRaWAN coverage in your area.
++> You can use the Dragino LG308 gateway to expand or create LoRaWAN coverage in your area.
  )))
  (((
@@ -60,12 +60,12 @@
  * Power Consumption:
  ** Idle: 4mA@12v
  ** 20dB Transmit: 34mA@12v
--* Operating Temperature: -40 ~~ 85 Degrees, No Dew
++* Operating Temperature: -40 ~~ 85 Degree, No Dew
  (% style="color:#037691" %)**Interface for Model: LT22222-L:**
  * 2 x Digital dual direction Input (Detect High/Low signal, Max: 50v, or 220v with optional external resistor)
--* 2 x Digital Output (NPN output. Max pull-up voltage 36V,450mA)
++* 2 x Digital Output (NPN output. Max pull up voltage 36V,450mA)
  * 2 x Relay Output (5A@250VAC / 30VDC)
  * 2 x 0~~20mA Analog Input (res:0.01mA)
  * 2 x 0~~30V Analog Input (res:0.01v)
@@ -78,7 +78,7 @@
  ** Band 2 (LF): 410 ~~ 528 Mhz
  * 168 dB maximum link budget.
  * +20 dBm - 100 mW constant RF output vs.
--* +14 dBm high-efficiency PA.
++* +14 dBm high efficiency PA.
  * Programmable bit rate up to 300 kbps.
  * High sensitivity: down to -148 dBm.
  * Bullet-proof front end: IIP3 = -12.5 dBm.
@@ -98,7 +98,7 @@
  * Optional Customized LoRa Protocol
  * Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/RU864/IN865/MA869
  * AT Commands to change parameters
--* Remotely configure parameters via LoRaWAN Downlink
++* Remote configure parameters via LoRa Downlink
  * Firmware upgradable via program port
  * Counting
@@ -139,7 +139,7 @@
  * 1 x bracket for wall mounting
  * 1 x programming cable
--Attach the LoRaWAN antenna to the antenna connector, ANT,** **located on the top right side of the device, next to the upper terminal block. Secure the antenna by tightening it clockwise.
++Attach the LoRaWAN antenna to the connector labeled **ANT** (located on the top right side of the device, next to the upper terminal block). Secure the antenna by tightening it clockwise.
  == 2.2 Terminals ==
@@ -169,9 +169,9 @@
  |(% style="width:296px" %)DO2|(% style="width:334px" %)Digital Output 2
  |(% style="width:296px" %)DO1|(% style="width:334px" %)Digital Output 1
--== 2.3 Powering the LT-22222-L ==
++== 2.3 Powering ==
--The LT-22222-L I/O Controller can be powered by a 7–24V DC power source. Connect the power supply’s positive wire to the VIN and the negative wire to the GND screw terminals. The power indicator (PWR) LED will turn on when the device is properly powered.
++The LT-22222-L I/O Controller can be powered by a 7–24V DC power source. Connect the power supply’s positive wire to the VIN screw terminal and the negative wire to the GND screw terminal. The power indicator (PWR) LED will turn on when the device is properly powered.
  [[image:1653297104069-180.png]]
@@ -181,9 +181,9 @@
  == 3.1 How does it work? ==
--By default, the LT-22222-L is configured to operate in LoRaWAN Class C mode. It supports OTAA (Over-the-Air Activation), the most secure method for activating a device with a LoRaWAN network server. The LT-22222-L comes with device registration information that allows you to register it with a LoRaWAN network, enabling the device to perform OTAA activation with the network server upon initial power-up and after any subsequent reboots.
++The LT-22222-L is configured to operate in LoRaWAN Class C mode by default. It supports OTAA (Over-the-Air Activation), which is the most secure method for activating a device with a LoRaWAN network server. The LT-22222-L comes with device registration information that allows you to register it with a LoRaWAN network, enabling the device to perform OTAA activation with the network server upon initial power-up and after any subsequent reboots.
--For LT-22222-L, the LED will show the Join status: After powering on, the TX LED will fast-blink 5 times which means the LT-22222-L will enter the working mode and start to JOIN the LoRaWAN network. The TX LED will be on for 5 seconds after joining the network. When there is a message from the server, the RX LED will be on for 1 second.
++For LT-22222-L, the LED will show the Join status: After power on (% style="color:green" %)**TX LED**(%%) will fast blink 5 times, LT-22222-L will enter working mode and start to JOIN LoRaWAN network. (% style="color:green" %)**TX LED**(%%) will be on for 5 seconds after joined in network. When there is message from server, the RX LED will be on for 1 second.
  In case you can't set the root key and other identifiers in the network server and must use them from the server, you can use [[AT Commands>>||anchor="H4.UseATCommand"]] to configure them on the device.
@@ -205,7 +205,7 @@
  * Log in to your [[The Things Stack Sandbox>>https://eu1.cloud.thethings.network]] account.
  * Create an application if you do not have one yet.
--* Register LT-22222-L with that application. Two registration options are available:
++* Register LT-22222-L with that application. Two registration options available:
  ==== Using the LoRaWAN Device Repository: ====
@@ -213,12 +213,12 @@
  * On the **Register end device** page:
  ** Select the option **Select the end device in the LoRaWAN Device Repository**.
  ** Choose the **End device brand**, **Model**, **Hardware version**, **Firmware version**, and **Profile (Region)**.
--** Select the **Frequency plan** that matches your device.
++** Select the **Frequency plan** that matches with your device.
  [[image:lt-22222-l-dev-repo-reg-p1.png||height="625" width="1000"]]
  *
--** Enter the **AppEUI** in the **JoinEUI** field and click the **Confirm** button.
++** Enter the **AppEUI** in the **JoinEUI** field and click **Confirm** button.
  ** Enter the **DevEUI** in the **DevEUI** field.
  ** Enter the **AppKey** in the **AppKey** field.
  ** In the **End device ID** field, enter a unique name within this application for your LT-22222-N.
@@ -229,26 +229,19 @@
  ==== Entering device information manually: ====
  * On the **Register end device** page:
--** Select the **Enter end device specifies manually** option as the input method.
--** Select the **Frequency plan** that matches your device.
++** Select the **Enter end device specified manually** option.
++** Select the **Frequency plan** that matches with your device.
  ** Select the **LoRaWAN version**.
  ** Select the **Regional Parameters version**.
--** Click **Show advanced activation, LoRaWAN class and cluster settings** link to expand the section.
--** Select **Over the air activation (OTAA)** option under the **Activation mode**
++** Click **Show advanced activation, LoRaWAN class and cluster settings** option.
++** Select **Over the air activation (OTAA)** option under **Activation mode**
  ** Select **Class C (Continuous)** from the **Additional LoRaWAN class capabilities**.
++** Enter **AppEUI** in the **JoinEUI** field and click **Confirm** button.
++** Enter **DevEUI** in the **DevEUI** field.
++** Enter **AppKey** in the **AppKey** field.
++** In the **End device ID** field, enter a unique name within this application for your LT-22222-N.
++** Under **After registration**, select the **View registered end device** option.
--[[image:lt-22222-l-manually-p1.png||height="625" width="1000"]]
--
--
--* Enter **AppEUI** in the **JoinEUI** field and click the **Confirm** button.
--* Enter **DevEUI** in the **DevEUI** field.
--* Enter **AppKey** in the **AppKey** field.
--* In the **End device ID** field, enter a unique name within this application for your LT-22222-N.
--* Under **After registration**, select the **View registered end device** option.
--
--[[image:lt-22222-l-manually-p2.png||height="625" width="1000"]]
--
--
  ==== Joining ====
  Click on **Live Data** in the left navigation. Then, power on the device, and it will join The Things Stack Sandbox. You can see the join request, join accept, followed by uplink messages form the device showing in the Live Data panel.
@@ -256,12 +256,12 @@
  [[image:1653298044601-602.png||height="405" width="709"]]
--== 3.3 Work Modes and their Uplink Payload formats ==
++== 3.3 Uplink Payload ==
--The LT-22222-L has 5 **work modes**. It also has an interrupt/trigger mode for different types of applications that can be used together with any working mode as an additional feature. The default mode is MOD1 and you can switch between these modes using AT commands.
++There are five working modes + one interrupt mode on LT for different type application:
--* (% style="color:blue" %)**MOD1**(%%): (default mode/factory set): 2ACI + 2AVI + DI + DO + RO
++* (% style="color:blue" %)**MOD1**(%%): (default setting): 2 x ACI + 2AVI + DI + DO + RO
  * (% style="color:blue" %)**MOD2**(%%): Double DI Counting + DO + RO
@@ -275,8 +275,9 @@
  === 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
++
  (((
--The uplink payload is 11 bytes long. Uplink messages are sent over LoRaWAN FPort 2. By default, one uplink is sent every 10 minutes. (% style="display:none" wfd-invisible="true" %)
++The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default. (% style="display:none" %)
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
  |(% style="background-color:#4f81bd; color:white" %)**Size(bytes)**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**1**|(% style="background-color:#4f81bd; color:white" %)**1**|(% style="background-color:#4f81bd; color:white" %)**1**
@@ -288,29 +288,29 @@
  ACI1 Current
  )))|(((
  ACI2 Current
--)))|**DIDORO***|(((
++)))|DIDORO*|(((
  Reserve
  )))|MOD
  )))
  (((
--(% style="color:#4f81bd" %)*** DIDORO**(%%) is a combination of RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1, and its size is1 byte long as shown below.
++(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
--|**bit 7**|**bit 6**|**bit 5**|**bit 4**|**bit 3**|**bit 2**|**bit 1**|**bit 0**
--|RO1|RO2|--DI3--|DI2|DI1|--DO3--|DO2|DO1
++|**bit7**|**bit6**|**bit5**|**bit4**|**bit3**|**bit2**|**bit1**|**bit0**
++|RO1|RO2|DI3|DI2|DI1|DO3|DO2|DO1
  )))
--* RO is for the relay. ROx=1: CLOSED, ROx=0 always OPEN.
--* DI is for digital input. DIx=1: HIGH or FLOATING, DIx=0: LOW.
--* DO is for reverse digital output. DOx=1: LOW, DOx=0: HIGH or FLOATING.
++* RO is for relay. ROx=1 : close, ROx=0 always open.
++* DI is for digital input. DIx=1: high or float, DIx=0: low.
++* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
--(% style="color:red" %)**Note: DI3 and DO3 bits are not valid for LT-22222-L**
++(% style="color:red" %)**Note: DI3 and DO3 bit are not valid for LT-22222-L**
--For example, if the payload is: [[image:image-20220523175847-2.png]]
++For example if payload is: [[image:image-20220523175847-2.png]]
--**The interface values can be calculated as follows:  **
++**The value for the interface is:  **
  AVI1 channel voltage is 0x04AB/1000=1195(DEC)/1000=1.195V
@@ -320,32 +320,35 @@
  ACI2 channel current is 0x1300/1000=4.864mA
--The last byte 0xAA= **10101010**(b) means,
++The last byte 0xAA= 10101010(B) means
--* [1] The RO1 relay channel is CLOSED, and the RO1 LED is ON.
--* [0] The RO2 relay channel is OPEN, and the RO2 LED is OFF.
--* [1] DI3 - not used for LT-22222-L.
--* [0] DI2 channel input is LOW, and the DI2 LED is OFF.
--* [1] DI1 channel input state:
--** DI1 is FLOATING when no sensor is connected between DI1+ and DI1-.
--** DI1 is HIGH when a sensor is connected between DI1- and DI1+ and the sensor is ACTIVE.
--** DI1 LED is ON in both cases.
--* [0] DO3 - not used for LT-22222-L.
--* [1] DO2 channel output is LOW, and the DO2 LED is ON.
--* [0] DO1 channel output state:
--** DO1 is FLOATING when there is no load between DO1 and V+.
--** DO1 is HIGH when there is a load between DO1 and V+.
--** DO1 LED is OFF in both cases.
++* [1] RO1 relay channel is close and the RO1 LED is ON.
++* [0] RO2 relay channel is open and RO2 LED is OFF;
++**LT22222-L:**
++
++* [1] DI2 channel is high input and DI2 LED is ON;
++* [0] DI1 channel is low input;
++
++* [0] DO3 channel output state
++** DO3 is float in case no load between DO3 and V+.;
++** DO3 is high in case there is load between DO3 and V+.
++** DO3 LED is off in both case
++* [1] DO2 channel output is low and DO2 LED is ON.
++* [0] DO1 channel output state
++** DO1 is float in case no load between DO1 and V+.;
++** DO1 is high in case there is load between DO1 and V+.
++** DO1 LED is off in both case
++
  === 3.3.2 AT+MOD~=2, (Double DI Counting) ===
  (((
--**For LT-22222-L**: In this mode, **DI1 and DI2** are used as counting pins.
++**For LT-22222-L**: this mode the **DI1 and DI2** are used as counting pins.
  )))
  (((
--The uplink payload is 11 bytes long.
++Total : 11 bytes payload
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
  |(% style="background-color:#4f81bd; color:white" %)**Size(bytes)**|(% style="background-color:#4f81bd; color:white" %)**4**|(% style="background-color:#4f81bd; color:white" %)**4**|(% style="background-color:#4f81bd; color:white" %)**1**|(% style="background-color:#4f81bd; color:white" %)**1**|(% style="background-color:#4f81bd; color:white" %)**1**
@@ -355,26 +355,26 @@
  )))
  (((
--(% style="color:#4f81bd" %)***DIDORO**(%%) is a combination of RO1, RO2, DO3, DO2 and DO1, and its size is 1 byte long as shown below.
++(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DO3, DO2 and DO1. Totally 1bytes as below
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
--|**bit 7**|**bit 6**|**bit 5**|**bit 4**|**bit 3**|**bit 2**|**bit 1**|**bit 0**
--|RO1|RO2|FIRST|Reserve|Reserve|--DO3--|DO2|DO1
++|**bit7**|**bit6**|**bit5**|**bit4**|**bit3**|**bit2**|**bit1**|**bit0**
++|RO1|RO2|FIRST|Reserve|Reserve|DO3|DO2|DO1
--* RO is for the relay. ROx=1: CLOSED,  ROx=0 always OPEN.
++RO is for relay. ROx=1 : close , ROx=0 always open.
  )))
--* FIRST: Indicates that this is the first packet after joining the network.
--* DO is for reverse digital output. DOx=1: LOW, DOx=0: HIGH or FLOATING.
++* FIRST: Indicate this is the first packet after join network.
++* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
  (((
--(% style="color:red" %)**Note: DO3 bit is not valid for LT-22222-L**
++(% style="color:red" %)**Note: DO3 bit is not valid for LT-22222-L.**
  )))
  (((
--**To activate this mode, run the following AT commands:**
++**To use counting mode, please run:**
  )))
  (((
@@ -395,17 +395,17 @@
  (((
  **For LT22222-L:**
--(% style="color:blue" %)**AT+TRIG1=0,100**(%%)** (sets the DI1 port to trigger on a LOW level. The valid signal duration is 100ms) **
++(% style="color:blue" %)**AT+TRIG1=0,100**(%%)**    (set DI1 port to trigger on low level, valid signal is 100ms) **
--(% style="color:blue" %)**AT+TRIG1=1,100**(%%)** (sets the DI1 port to trigger on a HIGH level. The valid signal duration is 100ms) **
++(% style="color:blue" %)**AT+TRIG1=1,100**(%%)**    (set DI1 port to trigger on high level, valid signal is 100ms ) **
--(% style="color:blue" %)**AT+TRIG2=0,100**(%%)** (sets the DI2 port to trigger on a LOW level. The valid signal duration is 100ms) **
++(% style="color:blue" %)**AT+TRIG2=0,100**(%%)**    (set DI2 port to trigger on low level, valid signal is 100ms) **
--(% style="color:blue" %)**AT+TRIG2=1,100**(%%)** (sets the DI2 port to trigger on a HIGH level. The valid signal duration is 100ms) **
++(% style="color:blue" %)**AT+TRIG2=1,100**(%%)**    (set DI2 port to trigger on high level, valid signal is 100ms ) **
--(% style="color:blue" %)**AT+SETCNT=1,60**(%%)** (sets the COUNT1 value to 60)**
++(% style="color:blue" %)**AT+SETCNT=1,60**(%%)**   (Set COUNT1 value to 60)**
--(% style="color:blue" %)**AT+SETCNT=2,60 **(%%)**(sets the COUNT2 value to 60)**
++(% style="color:blue" %)**AT+SETCNT=2,60**(%%)**   (Set COUNT2 value to 60)**
  )))
@@ -412,7 +412,7 @@
  === 3.3.3 AT+MOD~=3, Single DI Counting + 2 x ACI ===
--**LT22222-L**: In this mode, the DI1 is used as a counting pin.
++**LT22222-L**: This mode the DI1 is used as a counting pin.
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
  |(% style="background-color:#4f81bd; color:white" %)**Size(bytes)**|(% style="background-color:#4f81bd; color:white" %)**4**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**1**|(% style="background-color:#4f81bd; color:white" %)**1**|(% style="background-color:#4f81bd; color:white" %)**1**
@@ -423,24 +423,24 @@
  )))|DIDORO*|Reserve|MOD
  (((
--(% style="color:#4f81bd" %)***DIDORO**(%%) is a combination of RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1, for a total of 1 byte, as shown below.
++(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
--|**bit 7**|**bit 6**|**bit 5**|**bit 4**|**bit 3**|**bit 2**|**bit 1**|**bit 0**
--|RO1|RO2|FIRST|Reserve|Reserve|--DO3--|DO2|DO1
++|**bit7**|**bit6**|**bit5**|**bit4**|**bit3**|**bit2**|**bit1**|**bit0**
++|RO1|RO2|FIRST|Reserve|Reserve|DO3|DO2|DO1
  )))
--* RO is for the relay. ROx=1: closed, ROx=0 always open.
--* FIRST: Indicates that this is the first packet after joining the network.
--* DO is for reverse digital output. DOx=1: output low, DOx=0: high or floating.
++* RO is for relay. ROx=1 : close, ROx=0 always open.
++* FIRST: Indicate this is the first packet after join network.
++* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
  (((
--(% style="color:red" %)**Note: DO3 bit is not valid for LT-22222-L.**
++(% style="color:red" %)**Note: DO3 is not valid for LT-22222-L.**
  )))
  (((
--**To activate this mode, run the following AT commands:**
++**To use counting mode, please run:**
  )))
  (((
@@ -453,9 +453,7 @@
  )))
  (((
--AT Commands for counting:
--
--The AT Commands for counting are similar to the [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]]s.
++Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
  )))
@@ -463,11 +463,11 @@
  (((
--**LT22222-L**: In this mode, the DI1 is used as a counting pin.
++**LT22222-L**: This mode the DI1 is used as a counting pin.
  )))
  (((
--The AVI1 is also used for counting. It monitors the voltage and checks it every **60 seconds**. If the voltage is higher or lower than VOLMAX mV, the AVI1 count increases by 1, allowing AVI1 counting to be used to measure a machine's working hours.
++The AVI1 is also used for counting. AVI1 is used to monitor the voltage. It will check the voltage **every 60s**, if voltage is higher or lower than VOLMAX mV, the AVI1 Counting increase 1, so AVI1 counting can be used to measure a machine working hour.
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
  |(% style="background-color:#4f81bd; color:white" %)**Size(bytes)**|(% style="background-color:#4f81bd; color:white" %)**4**|(% style="background-color:#4f81bd; color:white" %)**4**|(% style="background-color:#4f81bd; color:white" %)**1**|(% style="background-color:#4f81bd; color:white" %)**1**|(% style="background-color:#4f81bd; color:white" %)**1**
@@ -477,25 +477,25 @@
  )))
  (((
--(% style="color:#4f81bd" %)**DIDORO **(%%)is a combination of RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1, for a total of 1 byte, as shown below.
++(% style="color:#4f81bd" %)**DIDORO **(%%)is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
--|**bit 7**|**bit 6**|**bit 5**|**bit 4**|**bit 3**|**bit 2**|**bit 1**|**bit 0**
--|RO1|RO2|FIRST|Reserve|Reserve|--DO3--|DO2|DO1
++|**bit7**|**bit6**|**bit5**|**bit4**|**bit3**|**bit2**|**bit1**|**bit0**
++|RO1|RO2|FIRST|Reserve|Reserve|DO3|DO2|DO1
  )))
--* RO is for the relay. ROx=1: closed, ROx=0 always open.
--* FIRST: Indicates that this is the first packet after joining the network.
--* DO is for reverse digital output. DOx=1: output low, DOx=0: high or floating.
++* RO is for relay. ROx=1 : close, ROx=0 always open.
++* FIRST: Indicate this is the first packet after join network.
++* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
  (((
--(% style="color:red" %)**Note: DO3 bit is not valid for LT-22222-L.**
++(% style="color:red" %)**Note: DO3 is not valid for LT-22222-L.**
  )))
  (((
--**To activate this mode, run the following AT commands:**
++**To use this mode, please run:**
  )))
  (((
@@ -508,19 +508,19 @@
  )))
  (((
--Other AT Commands for counting are similar to the [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]]s.
++Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
  )))
  (((
--**In addition to that,  below are the commands for AVI1 Counting:**
++**Plus below command for AVI1 Counting:**
--(% style="color:blue" %)**AT+SETCNT=3,60**(%%)**           (Sets AVI Count to 60)**
++(% style="color:blue" %)**AT+SETCNT=3,60**(%%)**            (set AVI Count to 60)**
  (% style="color:blue" %)**AT+VOLMAX=20000**(%%)**       (If AVI1 voltage higher than VOLMAX (20000mV =20v), counter increase 1)**
  (% style="color:blue" %)**AT+VOLMAX=20000,0**(%%)**    (If AVI1 voltage lower than VOLMAX (20000mV =20v), counter increase 1)**
--(% style="color:blue" %)**AT+VOLMAX=20000,1**(%%)**    (If AVI1 voltage higher than VOLMAX (20000mV =20v), counter increase 1)**
++(% style="color:blue" %)**AT+VOLMAX=20000,1**(%%)**    (If AVI1 voltage higer than VOLMAX (20000mV =20v), counter increase 1)**
  )))
@@ -527,7 +527,7 @@
  === 3.3.5 AT+MOD~=5, Single DI Counting + 2 x AVI + 1 x ACI ===
--**LT22222-L**: In this mode, the DI1 is used as a counting pin.
++**LT22222-L**: This mode the DI1 is used as a counting pin.
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
  |(% style="background-color:#4f81bd; color:white" %)**Size(bytes)**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**2**|(% style="background-color:#4f81bd; color:white" %)**1**|(% style="background-color:#4f81bd; color:white" %)**1**|(% style="background-color:#4f81bd; color:white" %)**1**
@@ -542,25 +542,25 @@
  )))|MOD
  (((
--(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination of RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1, for a total of 1 byte, as shown below.
++(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
--|**bit 7**|**bit 6**|**bit 5**|**bit 4**|**bit 3**|**bit 2**|**bit 1**|**bit 0**
++|**bit7**|**bit6**|**bit5**|**bit4**|**bit3**|**bit2**|**bit1**|**bit0**
  |RO1|RO2|FIRST|Reserve|Reserve|DO3|DO2|DO1
  )))
--* RO is for the relay. ROx=1: closed, ROx=0 always open.
--* FIRST: Indicates that this is the first packet after joining the network.
++* RO is for relay. ROx=1 : close, ROx=0 always open.
++* FIRST: Indicate this is the first packet after join network.
  * (((
--DO is for reverse digital output. DOx=1: output low, DOx=0: high or floating.
++DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
  )))
  (((
--(% style="color:red" %)**Note: DO3 bit is not valid for LT-22222-L.**
++(% style="color:red" %)**Note: DO3 is not valid for LT-22222-L.**
  )))
  (((
--**To activate this mode, run the following AT commands:**
++**To use this mode, please run:**
  )))
  (((
@@ -573,7 +573,7 @@
  )))
  (((
--Other AT Commands for counting are similar to the [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]]s.
++Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
  )))
@@ -580,46 +580,49 @@
  === 3.3.6 AT+ADDMOD~=6. (Trigger Mode, Optional) ===
--(% style="color:#4f81bd" %)**This mode is optional and intended for trigger purposes. It can operate together with other modes.**
++(% style="color:#4f81bd" %)**This mode is an optional mode for trigger purpose. It can run together with other mode.**
--For example, if you configured the following commands:
++For example, if user has configured below commands:
  * **AT+MOD=1 **            **~-~->**   The normal working mode
--* **AT+ADDMOD6=1**   **~-~->**   Enable trigger mode
++* **AT+ADDMOD6=1**   **~-~->**   Enable trigger
--The LT-22222-L will continuously monitor AV1, AV2, AC1, and AC2 every 5 seconds. LT will send uplink packets in two cases:
++LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
--1. Periodically uplink (Based on TDC time). The payload is the same as in normal mode (MOD=1 for the commands above). These are (% style="color:#4f81bd" %)**unconfirmed**(%%) uplinks.
--1. Trigger uplink when the trigger condition is met. LT will send two packets in this case. The first uplink uses the payload specified in trigger mode (MOD=6). The second packet uses the normal mode payload (MOD=1 as set above). Both are (% style="color:#4f81bd" %)**CONFIRMED uplinks.**
++1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
++1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
  (% style="color:#037691" %)**AT Command to set Trigger Condition**:
--(% style="color:#4f81bd" %)**Trigger based on voltage**:
++(% style="color:#4f81bd" %)**Trigger base on voltage**:
++
  Format: AT+AVLIM=<AV1_LIMIT_LOW>,< AV1_LIMIT_HIGH>,<AV2_LIMIT_LOW>,< AV2_LIMIT_HIGH>
  **Example:**
--AT+AVLIM=3000,6000,0,2000   (triggers an uplink if AVI1 voltage is lower than 3V or higher than 6V, or if AV2 voltage is higher than 2V)
++AT+AVLIM=3000,6000,0,2000   (If AVI1 voltage lower than 3v or higher than 6v.  or AV2 voltage is higher than 2v, LT will trigger Uplink)
--AT+AVLIM=5000,0,0,0   (triggers an uplink if AVI1 voltage lower than 5V. Use 0 for parameters that are not in use)
++AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
--(% style="color:#4f81bd" %)**Trigger based on current**:
++(% style="color:#4f81bd" %)**Trigger base on current**:
++
  Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
  **Example:**
--AT+ACLIM=10000,15000,0,0   (triggers an uplink if ACI1 voltage is lower than 10mA or higher than 15mA)
++AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
--(% style="color:#4f81bd" %)**Trigger based on DI status**:
--DI status triggers Flag.
++(% style="color:#4f81bd" %)**Trigger base on DI status**:
++DI status trigger Flag.
++
  Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
@@ -628,38 +628,39 @@
  AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
--(% style="color:#037691" %)**LoRaWAN Downlink Commands for Setting the Trigger Conditions:**
++(% style="color:#037691" %)**Downlink Command to set Trigger Condition:**
  Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
  Format: AA xx yy1 yy1 yy2 yy2 yy3 yy3 yy4 yy4
--  AA: Type Code for this downlink Command:
++  AA: Code for this downlink Command:
--  xx: **0**: Limit for AV1 and AV2; **1**: limit for AC1 and AC2; **2**: DI1and DI2 trigger enable/disable.
++  xx: 0: Limit for AV1 and AV2;  1: limit for AC1 and AC2 ; 2 DI1, DI2 trigger enable/disable
--  yy1 yy1: AC1 or AV1 LOW limit or DI1/DI2 trigger status.
++  yy1 yy1: AC1 or AV1 low limit or DI1/DI2 trigger status.
--  yy2 yy2: AC1 or AV1 HIGH limit.
++  yy2 yy2: AC1 or AV1 high limit.
--  yy3 yy3: AC2 or AV2 LOW limit.
++  yy3 yy3: AC2 or AV2 low limit.
--  Yy4 yy4: AC2 or AV2 HIGH limit.
++  Yy4 yy4: AC2 or AV2 high limit.
--**Example 1**: AA 00 13 88 00 00 00 00 00 00
++**Example1**: AA 00 13 88 00 00 00 00 00 00
--Same as AT+AVLIM=5000,0,0,0 (triggers an uplink if AVI1 voltage is lower than 5V. Use 0s for parameters that are not in use)
++Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
--**Example 2**: AA 02 01 00
++**Example2**: AA 02 01 00
--Same as AT+ DTRI =1,0 (Enable DI1 trigger / disable DI2 trigger)
++Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
++
  (% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
--MOD6 Payload: total of 11 bytes
++MOD6 Payload : total 11 bytes payload
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)
  |(% style="background-color:#4f81bd; color:white; width:60px" %)**Size(bytes)**|(% style="background-color:#4f81bd; color:white; width:69px" %)**1**|(% style="background-color:#4f81bd; color:white; width:69px" %)**1**|(% style="background-color:#4f81bd; color:white; width:109px" %)**1**|(% style="background-color:#4f81bd; color:white; width:49px" %)**6**|(% style="background-color:#4f81bd; color:white; width:109px" %)**1**|(% style="background-color:#4f81bd; color:white; width:50px" %)**1**
@@ -673,10 +673,10 @@
  MOD(6)
  )))
--(% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if the trigger is set for this part. Totally 1 byte as below
++(% style="color:#4f81bd" %)**TRI FLAG1**(%%) is a combination to show if trigger is set for this part. Totally 1byte as below
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)
--|**bit 7**|**bit 6**|**bit 5**|**bit 4**|**bit 3**|**bit 2**|**bit 1**|**bit 0**
++|**bit7**|**bit6**|**bit5**|**bit4**|**bit3**|**bit2**|**bit1**|**bit0**
  |(((
  AV1_LOW
  )))|(((
@@ -695,17 +695,17 @@
  AC2_HIGH
  )))
--* Each bit shows if the corresponding trigger has been configured.
++* Each bits shows if the corresponding trigger has been configured.
  **Example:**
--10100000: Means the system has configure to use the trigger: AV1_LOW and AV2_LOW
++10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
--(% style="color:#4f81bd" %)**TRI Status1**(%%) is a combination to show which condition is trigger. Totally 1 byte as below
++(% style="color:#4f81bd" %)**TRI Status1**(%%) is a combination to show which condition is trigger. Totally 1byte as below
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)
--|**bit 7**|**bit 6**|**bit 5**|**bit 4**|**bit 3**|**bit 2**|**bit 1**|**bit 0**
++|**bit7**|**bit6**|**bit5**|**bit4**|**bit3**|**bit2**|**bit1**|**bit0**
  |(((
  AV1_LOW
  )))|(((
@@ -724,11 +724,11 @@
  AC2_HIGH
  )))
--* Each bit shows which status has been triggered on this uplink.
++* Each bits shows which status has been trigger on this uplink.
  **Example:**
--10000000: Means this uplink is triggered by AV1_LOW. That means the voltage is too low.
++10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
  (% style="color:#4f81bd" %)**TRI_DI FLAG+STA **(%%)is a combination to show which condition is trigger. Totally 1byte as below
@@ -737,7 +737,7 @@
  |**bit7**|**bit6**|**bit5**|**bit4**|**bit3**|**bit2**|**bit1**|**bit0**
  |N/A|N/A|N/A|N/A|DI2_STATUS|DI2_FLAG|DI1_STATUS|DI1_FLAG
--* Each bits shows which status has been triggered on this uplink.
++* Each bits shows which status has been trigger on this uplink.
  **Example:**
@@ -764,11 +764,11 @@
  )))
--== 3.4 Configure LT via AT Commands or Downlinks ==
++== 3.4 Configure LT via AT or Downlink ==
  (((
--User can configure LT I/O Controller via AT Commands or LoRaWAN Downlinks.
++User can configure LT I/O Controller via AT Commands or LoRaWAN Downlink Commands
  )))
  (((
@@ -794,37 +794,33 @@
  ==== 3.4.2.1 Set Transmit Interval ====
--Sets the uplink interval of the device. The default uplink transmission interval is 10 minutes.
++Set device uplink interval.
--* (% style="color:#037691" %)**AT command:**
++* (% style="color:#037691" %)**AT Command:**
--(% style="color:blue" %)**AT+TDC=N**
++(% style="color:blue" %)**AT+TDC=N **
--where N is the time in milliseconds.
--**Example: **AT+TDC=30000. This will set the uplink interval to 30 seconds
++**Example: **AT+TDC=30000. Means set interval to 30 seconds
--* (% style="color:#037691" %)**Downlink payload (prefix 0x01):**
++* (% style="color:#037691" %)**Downlink Payload (prefix 0x01):**
  (% style="color:blue" %)**0x01 aa bb cc  **(%%)**   ~/~/ Same as AT+TDC=0x(aa bb cc)**
--==== 3.4.2.2 Set the Work Mode (AT+MOD) ====
++==== 3.4.2.2 Set Work Mode (AT+MOD) ====
--Sets the work mode.
++Set work mode.
--* (% style="color:#037691" %)**AT command:**(%%) (% style="color:blue" %)**AT+MOD=N  **
++* (% style="color:#037691" %)**AT Command:**(%%) (% style="color:blue" %)**AT+MOD=N  **
--Where N is the work mode.
++**Example**: AT+MOD=2. Set work mode to Double DI counting mode
--**Example**: AT+MOD=2. This will set the work mode to Double DI counting mode.
++* (% style="color:#037691" %)**Downlink Payload (prefix 0x0A):**
--
--* (% style="color:#037691" %)**Downlink payload (prefix 0x0A):**
--
  (% style="color:blue" %)**0x0A aa  **(%%)**  ** ~/~/ Same as AT+MOD=aa
@@ -832,12 +832,10 @@
  ==== 3.4.2.3 Poll an uplink ====
--Asks the device to send an uplink.
++* (% style="color:#037691" %)**AT Command:**(%%) There is no AT Command to poll uplink
--* (% style="color:#037691" %)**AT command:**(%%) There is no AT Command to poll uplink
++* (% style="color:#037691" %)**Downlink Payload (prefix 0x08):**
--* (% style="color:#037691" %)**Downlink payload (prefix 0x08):**
--
  (% style="color:blue" %)**0x08 FF  **(%%)**   **~/~/ Poll an uplink
  **Example**: 0x08FF, ask device to send an Uplink
@@ -844,16 +844,16 @@
--==== 3.4.2.4 Enable/Disable Trigger Mode ====
++==== 3.4.2.4 Enable Trigger Mode ====
--Enable or disable the trigger mode (see also [[ADDMOD6>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]).
++Use of trigger mode, please check [[ADDMOD6>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
  * (% style="color:#037691" %)**AT Command:**(%%) (% style="color:blue" %)**AT+ADDMOD6=1 or 0**
--(% style="color:red" %)**1:** (%%)Enable the trigger mode
++(% style="color:red" %)**1:** (%%)Enable Trigger Mode
--(% style="color:red" %)**0: **(%%)Disable the trigger mode
++(% style="color:red" %)**0: **(%%)Disable Trigger Mode
  * (% style="color:#037691" %)**Downlink Payload (prefix 0x0A 06):**
@@ -865,7 +865,7 @@
  ==== 3.4.2.5 Poll trigger settings ====
--Polls the trigger settings
++Poll trigger settings
  * (% style="color:#037691" %)**AT Command:**
@@ -873,7 +873,7 @@
  * (% style="color:#037691" %)**Downlink Payload (prefix 0x AB 06):**
--(% style="color:blue" %)**0xAB 06  **  (%%)   ~/~/ Poll the trigger settings. Device will uplink trigger settings once receive this command
++(% style="color:blue" %)**0xAB 06  **  (%%)   ~/~/ Poll trigger settings, device will uplink trigger settings once receive this command
@@ -880,11 +880,11 @@
  ==== 3.4.2.6 Enable / Disable DI1/DI2/DI3 as trigger ====
--Enable or Disable DI1/DI2/DI2 as trigger,
++Enable Disable DI1/DI2/DI2 as trigger,
  * (% style="color:#037691" %)**AT Command:**(%%) (% style="color:blue" %)**Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >**
--**Example:** AT+ DTRI =1,0 (Enable DI1 trigger / disable DI2 trigger)
++**Example:** AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
  * (% style="color:#037691" %)**Downlink Payload (prefix 0xAA 02):**
@@ -916,15 +916,15 @@
  ==== 3.4.2.8 Trigger2 – Set DI2 as trigger ====
--Sets DI2 trigger.
++Set DI2 trigger.
  * (% style="color:#037691" %)**AT Command:**(%%) (% style="color:blue" %)**AT+TRIG2=a,b**
--(% style="color:red" %)**a :** (%%)Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge (for MOD=1).
++(% style="color:red" %)**a :** (%%)Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge(for MOD=1).
  (% style="color:red" %)**b :** (%%)delay timing.
--**Example:** AT+TRIG2=0,100 (set DI1 port to trigger on low level, valid signal is 100ms )
++**Example:** AT+TRIG2=0,100(set DI1 port to trigger on low level, valid signal is 100ms )
  * (% style="color:#037691" %)**Downlink Payload (prefix 0x09 02 ):**
@@ -962,7 +962,7 @@
  ==== 3.4.2.11 Trigger – Set minimum interval ====
--Sets AV and AC trigger minimum interval.  Device won't response to the second trigger within this set time after the first trigger.
++Set AV and AC trigger minimum interval, system won't response to the second trigger within this set time after the first trigger.
  * (% style="color:#037691" %)**AT Command**(%%): (% style="color:blue" %)**AT+ATDC=5        ** ~/~/ (%%)Device won't response the second trigger within 5 minute after the first trigger.
@@ -1110,7 +1110,7 @@
  )))
  (((
--00: Closed ,  01: Open , 11: No action
++00: Close ,  01: Open , 11: No action
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:320px" %)
  |(% style="background-color:#4f81bd; color:white" %)**Downlink Code**|(% style="background-color:#4f81bd; color:white" %)**RO1**|(% style="background-color:#4f81bd; color:white" %)**RO2**
@@ -1232,7 +1232,7 @@
--==== 3.4.2.19 Counting ~-~- Change counting mode to save time ====
++==== 3.4.2.19 Counting ~-~- Change counting mode save time ====
  * (% style="color:#037691" %)**AT Command:**
@@ -1418,26 +1418,26 @@
  [[image:thingseye-io-step-6.png||height="625" width="1000"]]
--== 3.6 Interface Details ==
++== 3.6 Interface Detail ==
  === 3.6.1 Digital Input Port: DI1/DI2 /DI3 ( For LT-33222-L, low active ) ===
--Support NPN-type sensor
++Support NPN Type sensor
  [[image:1653356991268-289.png]]
--=== 3.6.2 Digital Input Ports: DI1/DI2 ( For LT-22222-L) ===
++=== 3.6.2 Digital Input Port: DI1/DI2 ( For LT-22222-L) ===
  (((
--The DI ports of the LT-22222-L can support **NPN**, **PNP**, or **dry contact** output sensors.
++The DI port of LT-22222-L can support **NPN** or **PNP** or **Dry Contact** output sensor.
  )))
  (((
  (((
--The part of the internal circuit of the LT-22222-L shown below includes the NEC2501 photocoupler. The active current from NEC2501 pin 1 to pin 2 is 1 mA, with a maximum allowable current of 50 mA. When active current flows from NEC2501 pin 1 to pin 2, the DI becomes active HIGH and the DI LED status changes.
++Internal circuit as below, the NEC2501 is a photocoupler, the Active current (from NEC2501 pin 1 to pin 2 is 1ma and the max current is 50mA). (% class="mark" %)When there is active current pass NEC2501 pin1 to pin2. The DI will be active high and DI LED status will change.
  )))
@@ -1447,7 +1447,7 @@
  (((
  (((
--(% style="color:#000000; font-family:Arial,sans-serif; font-size:11pt; font-style:normal; font-variant-alternates:normal; font-variant-east-asian:normal; font-variant-ligatures:normal; font-variant-numeric:normal; font-variant-position:normal; font-weight:400; text-decoration:none; white-space:pre-wrap" %)When connecting a device to the DI port, both DI1+ and DI1- must be connected.
++When use need to connect a device to the DI port, both DI1+ and DI1- must be connected.
  )))
  )))
@@ -1456,22 +1456,22 @@
  )))
  (((
--(% style="color:#0000ff" %)**Example 1**(%%): Connecting to a low-active sensor.
++(% style="color:blue" %)**Example1**(%%): Connect to a Low active sensor.
  )))
  (((
--This type of sensor outputs a low (GND) signal when active.
++This type of sensor will output a low signal GND when active.
  )))
  * (((
--Connect the sensor's output to DI1-
++Connect sensor's output to DI1-
  )))
  * (((
--Connect the sensor's VCC to DI1+.
++Connect sensor's VCC to DI1+.
  )))
  (((
--When the sensor is active, the current between NEC2501 pin 1 and pin 2 will be：
++So when sensor active, the current between NEC2501 pin1 and pin2 is：
  )))
  (((
@@ -1479,7 +1479,7 @@
  )))
  (((
--For example, if** DI1+ **= **12V**, the resulting current is [[image:1653968155772-850.png||height="23" width="19"]]= 12mA. Therefore, the LT-22222-L will be able to detect this active signal.
++If** DI1+ **= **12v**, the [[image:1653968155772-850.png||height="23" width="19"]]= 12mA , So the LT-22222-L will be able to detect this active signal.
  )))
  (((
@@ -1487,22 +1487,22 @@
  )))
  (((
--(% style="color:#0000ff" %)**Example 2**(%%): Connecting to a high-active sensor.
++(% style="color:blue" %)**Example2**(%%): Connect to a High active sensor.
  )))
  (((
--This type of sensor outputs a high signal (e.g., 24V) when active.
++This type of sensor will output a high signal (example 24v) when active.
  )))
  * (((
--Connect the sensor's output to DI1+
++Connect sensor's output to DI1+
  )))
  * (((
--Connect the sensor's GND DI1-.
++Connect sensor's GND DI1-.
  )))
  (((
--When the sensor is active, the current between NEC2501 pin1 and pin2 will be:
++So when sensor active, the current between NEC2501 pin1 and pin2 is:
  )))
  (((
@@ -1510,7 +1510,7 @@
  )))
  (((
--If **DI1+ = 24V**, the resulting current[[image:1653968155772-850.png||height="23" width="19"]] is 24mA, Therefore, the LT-22222-L will detect this high-active signal.
++If **DI1+ = 24v**, the[[image:1653968155772-850.png||height="23" width="19"]] 24mA , So the LT-22222-L will be able to detect this high active signal.
  )))
  (((
@@ -1518,22 +1518,22 @@
  )))
  (((
--(% style="color:#0000ff" %)**Example 3**(%%): Connecting to a 220V high-active sensor.
++(% style="color:blue" %)**Example3**(%%): Connect to a 220v high active sensor.
  )))
  (((
--Assume that you want to monitor an active signal higher than 220V without damaging the photocoupler
++Assume user want to monitor an active signal higher than 220v, to make sure not burn the photocoupler
  )))
  * (((
--Connect the sensor's output to DI1+ with a 50K resistor in series.
++Connect sensor's output to DI1+ with a serial 50K resistor
  )))
  * (((
--Connect the sensor's GND DI1-.
++Connect sensor's GND DI1-.
  )))
  (((
--When the sensor is active, the current between NEC2501 pin1 and pin2 will be:
++So when sensor active, the current between NEC2501 pin1 and pin2 is:
  )))
  (((
@@ -1541,37 +1541,37 @@
  )))
  (((
--If the sensor output is 220V, then [[image:1653968155772-850.png||height="23" width="19"]](% id="cke_bm_243359S" style="display:none" wfd-invisible="true" %)[[image:image-20220524095628-8.png]](%%) = DI1+ / 51K  = 4.3mA. Therefore, the LT-22222-L will be able to safely detect this high-active signal.
++If sensor output is 220v, the [[image:1653968155772-850.png||height="23" width="19"]](% id="cke_bm_243359S" style="display:none" %)[[image:image-20220524095628-8.png]](%%) = DI1+ / 51K.  = 4.3mA , So the LT-22222-L will be able to detect this high active signal safely.
  )))
--(% style="color:blue" %)**Example4**(%%): Connecting to Dry Contact sensor
++(% style="color:blue" %)**Example4**(%%): Connect to Dry Contact sensor
--From the DI port circuit above, you can see that activating the photocoupler requires a voltage difference between the DI+ and DI- ports. However, the Dry Contact sensor is a passive component and cannot provide this voltage difference.
++From above DI ports circuit, we can see that active the photocoupler will need to have a voltage difference between DI+ and DI- port. While the Dry Contact sensor is a passive component which can't provide this voltage difference.
--To detect a Dry Contact, you can supply a power source to one pin of the Dry Contact. Below is a reference circuit diagram.
++To detect a Dry Contact, we can provide a power source to one pin of the Dry Contact. Below is a reference connection.
  [[image:image-20230616235145-1.png]]
--(% style="color:blue" %)**Example5**(%%): Connecting to an Open Collector
++(% style="color:blue" %)**Example5**(%%): Connect to Open Colleactor
  [[image:image-20240219115718-1.png]]
--=== 3.6.3 Digital Output Ports: DO1/DO2 /DO3 ===
++=== 3.6.3 Digital Output Port: DO1/DO2 /DO3 ===
--(% style="color:blue" %)**NPN output**(%%): GND or Float. The maximum voltage that can be applied to the output pin is 36V.
++(% style="color:blue" %)**NPN output**(%%): GND or Float. Max voltage can apply to output pin is 36v.
--(% style="color:red" %)**Note: The DO pins will float when the device is powered off.**
++(% style="color:red" %)**Note: DO pins go to float when device is power off.**
  [[image:1653357531600-905.png]]
--=== 3.6.4 Analog Input Interfaces ===
++=== 3.6.4 Analog Input Interface ===
--The analog input interface is shown below. The LT-22222-L will measure the IN2 voltage to calculate the current passing through the load. The formula is:
++The analog input interface is as below. The LT will measure the IN2 voltage so to calculate the current pass the Load. The formula is:
  (% style="color:blue" %)**AC2 = (IN2 voltage )/12**
@@ -1578,14 +1578,14 @@
  [[image:1653357592296-182.png]]
--Example:  Connecting a 4~~20mA sensor
++Example to connect a 4~~20mA sensor
--We will use the wind speed sensor as an example for reference only.
++We take the wind speed sensor as an example for reference only.
  (% style="color:blue" %)**Specifications of the wind speed sensor:**
--(% style="color:red" %)**Red:      12~~24V**
++(% style="color:red" %)**Red:      12~~24v**
  (% style="color:#ffc000" %)**Yellow:  4~~20mA**
@@ -1598,7 +1598,7 @@
  [[image:1653357648330-671.png||height="155" width="733"]]
--Example: Connecting to a regulated power supply to measure voltage
++Example connected to a regulated power supply to measure voltage
  [[image:image-20230608101532-1.png||height="606" width="447"]]
@@ -1607,7 +1607,7 @@
  [[image:image-20230608101722-3.png||height="102" width="1139"]]
--(% style="color:blue; font-weight:bold" %)**Specifications of the regulated power supply**(% style="color:blue" %)**:**
++(% style="color:blue; font-weight:bold" %)**Specifications of the regulated power**(%%) (% style="color:blue" %)**:**
  (% style="color:red" %)**Red:      12~~24v**
@@ -1618,9 +1618,9 @@
  (((
--The LT-22222-L has two relay interfaces, RO1 and RO2, each using two pins of the screw terminal (ROx-1 and ROx-2 where x is the port number, 1 or 2). You can connect a device's power line in series with one of the relay interfaces (e.g., RO1-1 and RO1-2 screw terminals). See the example below:
++The LT serial controller has two relay interfaces; each interface uses two pins of the screw terminal. User can connect other device's Power Line to in serial of RO1_1 and RO_2. Such as below:
--**Note**: The ROx pins will be in the Open (NO) state when the LT-22222-L is powered off.
++**Note**: RO pins go to Open(NO) when device is power off.
  )))
  [[image:image-20220524100215-9.png]]
@@ -1648,25 +1648,25 @@
  Transmit a LoRa packet: TX blinks once
  )))
  )))
--|**RX**|RX blinks once when receiving a packet.
--|**DO1**|For LT-22222-L: ON when DO1 is low, OFF when DO1 is high
--|**DO2**|For LT-22222-L: ON when DO2 is low, OFF when DO2 is high
++|**RX**|RX blinks once when receive a packet.
++|**DO1**|For LT-22222-L: ON when DO1 is low, LOW when DO1 is high
++|**DO2**|For LT-22222-L: ON when DO2 is low, LOW when DO2 is high
  |**DI1**|(((
--For LT-22222-L: ON when DI1 is high, OFF when DI1 is low
++For LT-22222-L: ON when DI1 is high, LOW when DI1 is low
  )))
  |**DI2**|(((
--For LT-22222-L: ON when DI2 is high, OFF when DI2 is low
++For LT-22222-L: ON when DI2 is high, LOW when DI2 is low
  )))
--|**RO1**|For LT-22222-L: ON when RO1 is closed, OFF when RO1 is open
--|**RO2**|For LT-22222-L: ON when RO2 is closed, OFF when RO2 is open
++|**RO1**|For LT-22222-L: ON when RO1 is closed, LOW when RO1 is open
++|**RO2**|For LT-22222-L: ON when RO2 is closed, LOW when RO2 is open
--= 4. Using AT Command =
++= 4. Use AT Command =
--== 4.1 Connecting the LT-22222-L to a computer ==
++== 4.1 Access AT Command ==
  (((
--The LT-22222-L supports programming using AT Commands. You can use a USB-to-TTL adapter along with a 3.5mm Program Cable to connect the LT-22222-L to a computer, as shown below.
++LT supports AT Command set. User can use a USB to TTL adapter plus the 3.5mm Program Cable to connect to LT for using AT command, as below.
  )))
  [[image:1653358238933-385.png]]
@@ -1673,7 +1673,7 @@
  (((
--On the PC, the user needs to set the (% style="color:#4f81bd" %)**serial tool**(%%)(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) to a baud rate of (% style="color:green" %)**9600**(%%) to access to access serial console of LT-22222-L. The AT commands are disabled by default, and a password (default:(% style="color:green" %)**123456**)(%%) must be entered to active them, as shown below:
++In PC, User needs to set (% style="color:#4f81bd" %)**serial tool**(%%)(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to (% style="color:green" %)**9600**(%%) to access to access serial console for LT. The AT commands are disable by default and need to enter password (default:(% style="color:green" %)**123456**)(%%) to active it. As shown below:
  )))
  [[image:1653358355238-883.png]]
@@ -1680,12 +1680,10 @@
  (((
--You can find more details in the [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/]]
++More detail AT Command manual can be found at [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/]]
  )))
  (((
--The following table lists all the AT commands related to the LT-22222-L, except for those used for switching between modes.
--
  AT+<CMD>?        : Help on <CMD>
  )))
@@ -2010,10 +2010,10 @@
  = 5. Case Study =
--== 5.1 Counting how many objects pass through the flow Line ==
++== 5.1 Counting how many objects pass in Flow Line ==
--Reference Link: [[How to set up to setup counting for objects passing through the flow line>>How to set up to count objects pass in flow line]]?
++Reference Link: [[How to set up to count objects pass in flow line>>How to set up to count objects pass in flow line]]?
  = 6. FAQ =
@@ -2021,26 +2021,26 @@
  == 6.1 How to upgrade the image? ==
--The LT-22222-L I/O Controller is shipped with a 3.5mm cable, which is used to upload an image to LT in order to:
++The LT LoRaWAN Controller is shipped with a 3.5mm cable, the cable is used to upload image to LT to:
--* Support new features.
--* Fix bugs.
++* Support new features
++* For bug fix
  * Change LoRaWAN bands.
--Below is the hardware connection setup for uploading an image to the LT:
++Below shows the hardware connection for how to upload an image to the LT:
  [[image:1653359603330-121.png]]
  (((
--(% style="color:#0000ff" %)**Step 1**(%%)**:** Download the F[[lash Loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].
--(% style="color:#0000ff" %)**Step 2**(%%)**:** Download the [[LT Image files>>https://www.dropbox.com/sh/g99v0fxcltn9r1y/AACrbrDN0AqLHbBat0ViWx5Da/LT-22222-L/Firmware?dl=0&subfolder_nav_tracking=1]].
--(% style="color:#0000ff" %)**Step 3**(%%)**:** Open the Flash Loader and choose the correct COM port to update.
++(% style="color:blue" %)**Step1**(%%)**:** Download [[flash loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].
++(% style="color:blue" %)**Step2**(%%)**:** Download the [[LT Image files>>https://www.dropbox.com/sh/g99v0fxcltn9r1y/AACrbrDN0AqLHbBat0ViWx5Da/LT-22222-L/Firmware?dl=0&subfolder_nav_tracking=1]].
++(% style="color:blue" %)**Step3**(%%)**:** Open flashloader; choose the correct COM port to update.
  (((
  (% style="color:blue" %)**For LT-22222-L**(%%):
--Hold down the PRO button, then momentarily press the RST reset button. The (% style="color:red" %)**DO1 LED**(%%) will change from OFF to ON. When the (% style="color:red" %)**DO1 LED**(%%) is ON, it indicates that the device is in download mode.
++Hold down the PRO button and then momentarily press the RST reset button and the (% style="color:red" %)**DO1 led**(%%) will change from OFF to ON. When (% style="color:red" %)**DO1 LED**(%%) is on, it means the device is in download mode.
  )))
@@ -2055,7 +2055,7 @@
  [[image:image-20220524104033-15.png]]
--(% style="color:red" %)**Note**(%%): If you have lost the programming cable, you can make one from a 3.5mm cable. The pin mapping is as follows:
++(% style="color:red" %)**Notice**(%%): In case user has lost the program cable. User can hand made one from a 3.5mm cable. The pin mapping is:
  [[image:1653360054704-518.png||height="186" width="745"]]
@@ -2069,13 +2069,13 @@
  )))
  (((
--You can follow the introductions on [[how to upgrade image>>||anchor="H5.1Howtoupgradetheimage3F"]]. When downloading, select the required image file.
++User can follow the introduction for [[how to upgrade image>>||anchor="H5.1Howtoupgradetheimage3F"]]. When download the images, choose the required image file for download.
  )))
  (((
--== 6.3 How to set up LT to work with a Single Channel Gateway, such as LG01/LG02? ==
++== 6.3 How to set up LT to work with Single Channel Gateway such as LG01/LG02? ==
  )))
@@ -2082,13 +2082,13 @@
  (((
  (((
--In this case, you need to set the LT-33222-L to work in ABP mode and transmit on only one frequency.
++In this case, users need to set LT-33222-L to work in ABP mode & transmit in only one frequency.
  )))
  )))
  (((
  (((
--Assume you have an LG02 working on the frequency 868400000. Below are the steps.
++Assume we have a LG02 working in the frequency 868400000 now , below is the step.
  )))
@@ -2095,7 +2095,7 @@
  )))
  (((
--(% style="color:#0000ff" %)**Step 1**(%%):  Log in to The Things Stack SANDBOX, create an ABP device in the application, and input the Network Session key (NwkSKey), App session key (AppSKey) of the device.
++(% style="color:blue" %)**Step1**(%%):  Log in TTN, Create an ABP device in the application and input the network session key (NETSKEY), app session key (APPSKEY) from the device.
  )))
@@ -2152,7 +2152,7 @@
  Please see this link: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/How%20to%20set%20the%20transmit%20time%20interval/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20set%20the%20transmit%20time%20interval/]]
--== 6.5 Can I see the counting event in Serial? ==
++== 6.5 Can I see counting event in Serial? ==
  (((
@@ -2159,10 +2159,10 @@
  User can run AT+DEBUG command to see the counting event in serial. If firmware too old and doesn't support AT+DEBUG. User can update to latest firmware first.
--== 6.6 Can I use point-to-point communication with LT-22222-L? ==
++== 6.6 Can i use point to point communication for LT-22222-L? ==
--Yes, please refer [[Point to Point Communication>>doc:Main. Point to Point Communication of LT-22222-L.WebHome]]. this is [[firmware>>https://github.com/dragino/LT-22222-L/releases]].
++Yes, please refer [[Point to Point Communication>>doc:Main. Point to Point Communication of LT-22222-L.WebHome]]  ，this is [[firmware>>https://github.com/dragino/LT-22222-L/releases]].
  )))

lt-22222-l-manually-p1.png

Size

@@ -1,1 +1,1 @@
--306.6 KB
++310.3 KB

Content

lt-22222-l-manually-p2.png

Size

@@ -1,1 +1,1 @@
--279.1 KB
++301.5 KB

Content

Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Summary

Details

Applications

Navigation