Last modified by Saxer Lin on 2025/04/15 17:24
<
From version < 134.1 >
edited by Edwin Chen
on 2024/05/08 22:32
To version < 130.2 >
edited by Xiaoling
on 2024/02/19 14:44
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Edwin
1 +XWiki.Xiaoling
Content
... ... @@ -3,10 +3,6 @@
3 3  
4 4  
5 5  
6 -
7 -
8 -
9 -
10 10  **Table of Contents:**
11 11  
12 12  {{toc/}}
... ... @@ -59,64 +59,153 @@
59 59  
60 60  == 1.2 Specifications ==
61 61  
58 +(((
59 +
60 +
62 62  (% style="color:#037691" %)**Hardware System:**
62 +)))
63 63  
64 -* STM32L072xxxx MCU
65 -* SX1276/78 Wireless Chip 
66 -* Power Consumption:
67 -** Idle: 4mA@12v
68 -** 20dB Transmit: 34mA@12v
69 -* Operating Temperature: -40 ~~ 85 Degree, No Dew
64 +* (((
65 +STM32L072xxxx MCU
66 +)))
67 +* (((
68 +SX1276/78 Wireless Chip 
69 +)))
70 +* (((
71 +(((
72 +Power Consumption:
73 +)))
70 70  
75 +* (((
76 +Idle: 4mA@12v
77 +)))
78 +* (((
79 +20dB Transmit: 34mA@12v
80 +)))
81 +)))
71 71  
83 +(((
84 +
85 +
72 72  (% style="color:#037691" %)**Interface for Model: LT22222-L:**
87 +)))
73 73  
74 -* 2 x Digital dual direction Input (Detect High/Low signal, Max: 50v, or 220v with optional external resistor)
75 -* 2 x Digital Output (NPN output. Max pull up voltage 36V,450mA)
76 -* 2 x Relay Output (5A@250VAC / 30VDC)
77 -* 2 x 0~~20mA Analog Input (res:0.01mA)
78 -* 2 x 0~~30V Analog Input (res:0.01v)
79 -* Power Input 7~~ 24V DC. 
89 +* (((
90 +2 x Digital dual direction Input (Detect High/Low signal, Max: 50v, or 220v with optional external resistor)
91 +)))
92 +* (((
93 +2 x Digital Output (NPN output. Max pull up voltage 36V,450mA)
94 +)))
95 +* (((
96 +2 x Relay Output (5A@250VAC / 30VDC)
97 +)))
98 +* (((
99 +2 x 0~~20mA Analog Input (res:0.01mA)
100 +)))
101 +* (((
102 +2 x 0~~30V Analog Input (res:0.01v)
103 +)))
104 +* (((
105 +Power Input 7~~ 24V DC. 
106 +)))
80 80  
108 +(((
109 +
81 81  
82 82  (% style="color:#037691" %)**LoRa Spec:**
112 +)))
83 83  
84 -* Frequency Range:
85 -** Band 1 (HF): 862 ~~ 1020 Mhz
86 -** Band 2 (LF): 410 ~~ 528 Mhz
87 -* 168 dB maximum link budget.
88 -* +20 dBm - 100 mW constant RF output vs.
89 -* +14 dBm high efficiency PA.
90 -* Programmable bit rate up to 300 kbps.
91 -* High sensitivity: down to -148 dBm.
92 -* Bullet-proof front end: IIP3 = -12.5 dBm.
93 -* Excellent blocking immunity.
94 -* Low RX current of 10.3 mA, 200 nA register retention.
95 -* Fully integrated synthesizer with a resolution of 61 Hz.
96 -* FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.
97 -* Built-in bit synchronizer for clock recovery.
98 -* Preamble detection.
99 -* 127 dB Dynamic Range RSSI.
100 -* Automatic RF Sense and CAD with ultra-fast AFC.
101 -* Packet engine up to 256 bytes with CRC.
114 +* (((
115 +(((
116 +Frequency Range:
117 +)))
102 102  
119 +* (((
120 +Band 1 (HF): 862 ~~ 1020 Mhz
121 +)))
122 +* (((
123 +Band 2 (LF): 410 ~~ 528 Mhz
124 +)))
125 +)))
126 +* (((
127 +168 dB maximum link budget.
128 +)))
129 +* (((
130 ++20 dBm - 100 mW constant RF output vs.
131 +)))
132 +* (((
133 ++14 dBm high efficiency PA.
134 +)))
135 +* (((
136 +Programmable bit rate up to 300 kbps.
137 +)))
138 +* (((
139 +High sensitivity: down to -148 dBm.
140 +)))
141 +* (((
142 +Bullet-proof front end: IIP3 = -12.5 dBm.
143 +)))
144 +* (((
145 +Excellent blocking immunity.
146 +)))
147 +* (((
148 +Low RX current of 10.3 mA, 200 nA register retention.
149 +)))
150 +* (((
151 +Fully integrated synthesizer with a resolution of 61 Hz.
152 +)))
153 +* (((
154 +FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.
155 +)))
156 +* (((
157 +Built-in bit synchronizer for clock recovery.
158 +)))
159 +* (((
160 +Preamble detection.
161 +)))
162 +* (((
163 +127 dB Dynamic Range RSSI.
164 +)))
165 +* (((
166 +Automatic RF Sense and CAD with ultra-fast AFC.
167 +)))
168 +* (((
169 +Packet engine up to 256 bytes with CRC.
170 +
171 +
172 +
173 +)))
174 +
103 103  == 1.3 Features ==
104 104  
177 +
105 105  * LoRaWAN Class A & Class C protocol
179 +
106 106  * Optional Customized LoRa Protocol
181 +
107 107  * Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/RU864/IN865/MA869
183 +
108 108  * AT Commands to change parameters
185 +
109 109  * Remote configure parameters via LoRa Downlink
187 +
110 110  * Firmware upgradable via program port
189 +
111 111  * Counting
112 112  
113 113  == 1.4 Applications ==
114 114  
194 +
115 115  * Smart Buildings & Home Automation
196 +
116 116  * Logistics and Supply Chain Management
198 +
117 117  * Smart Metering
200 +
118 118  * Smart Agriculture
202 +
119 119  * Smart Cities
204 +
120 120  * Smart Factory
121 121  
122 122  == 1.5 Hardware Variants ==
... ... @@ -138,10 +138,17 @@
138 138  
139 139  = 2. Power ON Device =
140 140  
226 +
227 +(((
141 141  The LT controller can be powered by 7 ~~ 24V DC power source. Connect VIN to Power Input V+ and GND to power input V- to power the LT controller.
229 +)))
142 142  
231 +(((
143 143  PWR will on when device is properly powered.
144 144  
234 +
235 +)))
236 +
145 145  [[image:1653297104069-180.png]]
146 146  
147 147  
... ... @@ -1063,7 +1063,7 @@
1063 1063  )))
1064 1064  
1065 1065  (((
1066 -00: Close ,  01: Open , 11: No action
1158 +01: Close ,  00: Open , 11: No action
1067 1067  
1068 1068  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:320px" %)
1069 1069  |(% style="background-color:#4f81bd; color:white" %)**Downlink Code**|(% style="background-color:#4f81bd; color:white" %)**RO1**|(% style="background-color:#4f81bd; color:white" %)**RO2**
... ... @@ -1494,6 +1494,7 @@
1494 1494  [[image:image-20240219115718-1.png]]
1495 1495  
1496 1496  
1589 +
1497 1497  === 3.6.3 Digital Output Port: DO1/DO2 /DO3 ===
1498 1498  
1499 1499  
... ... @@ -1568,8 +1568,8 @@
1568 1568  == 3.7 LEDs Indicators ==
1569 1569  
1570 1570  
1571 -(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
1572 -|(% style="background-color:#4f81bd; color:white; width:50px" %)**LEDs**|(% style="background-color:#4f81bd; color:white; width:460px" %)**Feature**
1664 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
1665 +|(% style="background-color:#4f81bd; color:white; width:50px" %)**LEDs**|(% style="background-color:#4f81bd; color:white; width:470px" %)**Feature**
1573 1573  |**PWR**|Always on if there is power
1574 1574  |**SYS**|(((
1575 1575  After device is powered on, the SYS will **fast blink in GREEN** for 5 times, means RS485-LN start to join LoRaWAN network. If join success, SYS will be **on GREEN for 5 seconds. **SYS will **blink Blue** on every upload and **blink Green** once receive a downlink message.
... ... @@ -1612,6 +1612,10 @@
1612 1612  LT supports AT Command set. User can use a USB to TTL adapter plus the 3.5mm Program Cable to connect to LT for using AT command, as below.
1613 1613  )))
1614 1614  
1708 +(((
1709 +
1710 +)))
1711 +
1615 1615  [[image:1653358238933-385.png]]
1616 1616  
1617 1617  

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0