Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Last modified by Saxer Lin on 2025/04/15 17:24

From version < 126.13 >

edited by Xiaoling
on 2023/06/19 16:05

To version < 127.1 >

edited by Bei Jinggeng
on 2023/08/21 09:08

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Author

@@ -1,1 +1,1 @@
--XWiki.Xiaoling
++XWiki.Bei

Content

@@ -189,6 +189,7 @@
  * Counting
++
  == 1.4  Applications ==
@@ -205,7 +205,6 @@
  * Smart Factory
--
  == 1.5 Hardware Variants ==
@@ -223,6 +223,7 @@
  * 1 x Counting Port
  )))
++
  = 2. Power ON Device =
@@ -294,7 +294,6 @@
  [[image:1653298023685-319.png]]
--
  (((
  (% style="color:blue" %)**Step 2**(%%): Power on LT and it will auto join to the TTN network. After join success, it will start to upload message to TTN and user can see in the panel.
@@ -321,6 +321,7 @@
  * (% style="color:blue" %)**ADDMOD6**(%%): Trigger Mode, Optional, used together with MOD1 ~~ MOD5
++
  === 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
@@ -350,7 +350,7 @@
  |RO1|RO2|DI3|DI2|DI1|DO3|DO2|DO1
  )))
--* RO is for relay. ROx=1 : close，ROx=0 always open.
++* RO is for relay. ROx=1 : close, ROx=0 always open.
  * DI is for digital input. DIx=1: high or float, DIx=0: low.
  * DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
@@ -361,7 +361,7 @@
  **The value for the interface is:  **
--AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V
++AVI1 channel voltage is 0x04AB/1000=1195(DEC)/1000=1.195V
  AVI2 channel voltage is 0x04AC/1000=1.196V
@@ -390,7 +390,6 @@
  ** DO1 LED is off in both case
--
  === 3.3.2 AT+MOD~=2, (Double DI Counting) ===
@@ -415,7 +415,7 @@
  |**bit7**|**bit6**|**bit5**|**bit4**|**bit3**|**bit2**|**bit1**|**bit0**
  |RO1|RO2|FIRST|Reserve|Reserve|DO3|DO2|DO1
--RO is for relay. ROx=1 : close，ROx=0 always open.
++RO is for relay. ROx=1 : close , ROx=0 always open.
  )))
  * FIRST: Indicate this is the first packet after join network.
@@ -423,6 +423,8 @@
  (((
  (% style="color:red" %)**Note: DO3 bit is not valid for LT-22222-L.**
++
++
  )))
  (((
@@ -429,7 +429,6 @@
  **To use counting mode, please run:**
  )))
--
  (((
  (% class="box infomessage" %)
  (((
@@ -483,7 +483,7 @@
  |RO1|RO2|FIRST|Reserve|Reserve|DO3|DO2|DO1
  )))
--* RO is for relay. ROx=1 : close，ROx=0 always open.
++* RO is for relay. ROx=1 : close, ROx=0 always open.
  * FIRST: Indicate this is the first packet after join network.
  * DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
@@ -505,7 +505,6 @@
  )))
  )))
--
  (((
  Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
  )))
@@ -536,12 +536,14 @@
  |RO1|RO2|FIRST|Reserve|Reserve|DO3|DO2|DO1
  )))
--* RO is for relay. ROx=1 : close，ROx=0 always open.
++* RO is for relay. ROx=1 : close, ROx=0 always open.
  * FIRST: Indicate this is the first packet after join network.
  * DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
  (((
  (% style="color:red" %)**Note: DO3 is not valid for LT-22222-L.**
++
++
  )))
  (((
@@ -557,7 +557,6 @@
  )))
  )))
--
  (((
  Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
  )))
@@ -600,7 +600,7 @@
  |RO1|RO2|FIRST|Reserve|Reserve|DO3|DO2|DO1
  )))
--* RO is for relay. ROx=1 : close，ROx=0 always open.
++* RO is for relay. ROx=1 : close, ROx=0 always open.
  * FIRST: Indicate this is the first packet after join network.
  * (((
  DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
@@ -611,12 +611,9 @@
  )))
  (((
--
--
  **To use this mode, please run:**
  )))
--
  (((
  (% class="box infomessage" %)
  (((
@@ -626,7 +626,6 @@
  )))
  )))
--
  (((
  Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
  )))
@@ -840,6 +840,7 @@
  * (% style="color:blue" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
++
  === 3.4.1 Common Commands ===
@@ -1437,7 +1437,6 @@
  [[image:1653356838789-523.png||height="337" width="740"]]
--
  After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
  [[image:image-20220524094909-1.png||height="335" width="729"]]
@@ -1591,7 +1591,6 @@
  [[image:image-20230616235145-1.png]]
--
  === 3.6.3 Digital Output Port: DO1/DO2 /DO3 ===
@@ -1701,6 +1701,7 @@
  |**RO1**|
  |**RO2**|
++
  = 4. Use AT Command =
  == 4.1 Access AT Command ==
@@ -2032,8 +2032,6 @@
  dir=LoRa_Gateway/&file=LoRaWAN%201.0.3%20Regional%20Parameters.xlsx]] to see what DR means.**
  **4. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5.**
--
--
  )))
  (((
@@ -2040,9 +2040,6 @@
  [[image:1653359097980-169.png||height="188" width="729"]]
  )))
--(((
--
--)))
  === 4.2.3 Change to Class A ===
@@ -2050,8 +2050,9 @@
  (((
  (% style="color:blue" %)**If sensor JOINED:**
--(% style="background-color:#dcdcdc" %)**AT+CLASS=A
--ATZ**
++(% style="background-color:#dcdcdc" %)**AT+CLASS=A**
++
++(% style="background-color:#dcdcdc" %)**ATZ**
  )))
@@ -2168,13 +2168,21 @@
  (((
  (% style="background-color:#dcdcdc" %)**123456** (%%)   :   Enter Password to have AT access.
++
  (% style="background-color:#dcdcdc" %)**AT+FDR**(%%)   :   Reset Parameters to Factory Default, Keys Reserve
++
  (% style="background-color:#dcdcdc" %)**AT+NJM=0** (%%) :   Set to ABP mode
++
  (% style="background-color:#dcdcdc" %)**AT+ADR=0** (%%)  :  Set the Adaptive Data Rate Off
++
  (% style="background-color:#dcdcdc" %)**AT+DR=5** (%%)    :   Set Data Rate (Set AT+DR=3 for 915 band)
++
  (% style="background-color:#dcdcdc" %)**AT+TDC=60000 **(%%)   :      Set transmit interval to 60 seconds
++
  (% style="background-color:#dcdcdc" %)**AT+CHS=868400000**(%%) : Set transmit frequency to 868.4Mhz
++
  (% style="background-color:#dcdcdc" %)**AT+DADDR=26 01 1A F1**(%%)  :  Set Device Address to 26 01 1A F1
++
  (% style="background-color:#dcdcdc" %)**ATZ**        (%%)                              :  Reset MCU
  )))
@@ -2186,7 +2186,7 @@
  [[image:1653360498588-932.png||height="485" width="726"]]
--== 6.4 How to change the uplink interval？ ==
++== 6.4 How to change the uplink interval? ==
  Please see this link: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/How%20to%20set%20the%20transmit%20time%20interval/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20set%20the%20transmit%20time%20interval/]]
@@ -2234,7 +2234,13 @@
  Firmware version needs to be no less than 1.6.0.
++== 6.10 Why does the LT22222 always report 15.585V when measuring AVI? ==
++
++It is likely that the GND is not connected during the measurement, or the wire connected to the GND is loose.
++
++
++
  = 7. Trouble Shooting =
  )))
@@ -2275,6 +2275,8 @@
  )))
++==   ==
++
  = 8. Order Info =
@@ -2292,6 +2292,7 @@
  * (% style="color:red" %)**IN865**(%%):   LT with frequency bands IN865
  * (% style="color:red" %)**CN779**(%%):  LT with frequency bands CN779
++
  = 9. Packing Info =
@@ -2309,6 +2309,7 @@
  * Package Size / pcs : 14.5 x 8 x 5 cm
  * Weight / pcs : 170g
++
  = 10. Support =

Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Summary

Details

Applications

Navigation