Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Last modified by Saxer Lin on 2025/04/15 17:24

From version < 112.3 >

edited by Xiaoling
on 2023/03/31 09:39

To version < 110.2 >

edited by Xiaoling
on 2022/12/23 08:41

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -183,6 +183,8 @@
  * Firmware upgradable via program port
  * Counting
++
++
  == 1.4  Applications ==
@@ -193,6 +193,8 @@
  * Smart Cities
  * Smart Factory
++
++
  == 1.5 Hardware Variants ==
@@ -207,6 +207,8 @@
  * 1 x Counting Port
  )))
++
++
  = 2. Power ON Device =
@@ -300,6 +300,8 @@
  * (% style="color:blue" %)**MOD5**(%%): Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
  * (% style="color:blue" %)**ADDMOD6**(%%): Trigger Mode, Optional, used together with MOD1 ~~ MOD5
++
++
  === 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
@@ -356,6 +356,8 @@
  ** DO1 is high in case there is load between DO1 and V+.
  ** DO1 LED is off in both case
++
++
  === 3.3.2 AT+MOD~=2, (Double DI Counting) ===
@@ -644,6 +644,7 @@
  AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
++
  (% style="color:#037691" %)**Downlink Command to set Trigger Condition:**
  Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
@@ -704,6 +704,7 @@
  10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
++
  (% style="color:#4f81bd" %)**TRI_DI FLAG+STA **(%%)is a combination to show which condition is trigger. Totally 1byte as below
  [[image:image-20220524090456-4.png]]
@@ -717,6 +717,7 @@
  00000101: Means both DI1 and DI2 trigger are enabled.
++
  (% style="color:#4f81bd" %)**Enable/Disable MOD6 **(%%): 0x01: MOD6 is enable. 0x00: MOD6 is disable.
  Downlink command to poll MOD6 status:
@@ -752,6 +752,8 @@
  * (% style="color:blue" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
++
++
  === 3.4.1 Common Commands ===
@@ -1051,9 +1051,8 @@
           Latching time. Unit: ms
++Note:
--(% style="color:red" %)**Note: **
--
     Since Firmware v1.6.0, the latch time support 4 bytes and 2 bytes
     Before Firmwre v1.6.0 the latch time only suport 2 bytes.
@@ -1082,7 +1082,7 @@
--==== 3.4.2. 14 Relay ~-~- Control Relay Output RO1/RO2 ====
++==== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ====
  * (% style="color:#037691" %)**AT Command:**
@@ -1142,9 +1142,8 @@
  (% style="color:#4f81bd" %)**Fourth/Fifth/Sixth/Seventh Bytes(cc)**(%%): Latching time. Unit: ms
++Note:
--(% style="color:red" %)**Note:**
--
     Since Firmware v1.6.0, the latch time support 4 bytes and 2 bytes
     Before Firmwre v1.6.0 the latch time only suport 2 bytes.
@@ -1155,7 +1155,7 @@
  **Example payload:**
--**~1. 05 01 11 07 D0**
++**~1. 05 01 11 07 D**
  Relay1 and Relay 2 will be set to NC , last 2 seconds, then change back to original state.
@@ -1523,9 +1523,9 @@
  === 3.6.3 Digital Output Port: DO1/DO2 /DO3 ===
--**(% style="color:blue" %)NPN output**: GND or Float. Max voltage can apply to output pin is 36v.
++**NPN output**: GND or Float. Max voltage can apply to output pin is 36v.
--**(% style="color:red" %)Note: DO pins go to float when device is power off.**
++Note: DO pins go to float when device is power off.
  [[image:1653357531600-905.png]]
@@ -1912,7 +1912,7 @@
  **3. Make sure SF / bandwidth setting in LG01/LG02 match the settings of AT+DR. refer [[this link>>url:http://www.dragino.com/downloads/index.php?
  dir=LoRa_Gateway/&file=LoRaWAN%201.0.3%20Regional%20Parameters.xlsx]] to see what DR means.**
--**4. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5.**
++**4. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5**
  )))
@@ -1936,19 +1936,11 @@
  )))
--= 5. Case Study =
++= 5. FAQ =
--== 5.1 Counting how many objects pass in Flow Line ==
++== 5.1 How to upgrade the image? ==
--Reference Link: [[How to set up to count objects pass in flow line>>How to set up to count objects pass in flow line]]?
--
--
--= 6. FAQ =
--
--== 6.1 How to upgrade the image? ==
--
--
  The LT LoRaWAN Controller is shipped with a 3.5mm cable, the cable is used to upload image to LT to:
  * Support new features
@@ -1976,10 +1976,8 @@
    [[image:image-20220524103407-12.png]]
--
  [[image:image-20220524103429-13.png]]
--
  [[image:image-20220524104033-15.png]]
@@ -1991,7 +1991,7 @@
  (((
  (((
--== 6.2 How to change the LoRa Frequency Bands/Region? ==
++== 5.2 How to change the LoRa Frequency Bands/Region? ==
  )))
@@ -2004,7 +2004,7 @@
  (((
--== 6.3 How to set up LT to work with Single Channel Gateway such as LG01/LG02? ==
++== 5.3 How to set up LT to work with Single Channel Gateway such as LG01/LG02? ==
  )))
@@ -2067,7 +2067,7 @@
  [[image:1653360498588-932.png||height="485" width="726"]]
--== 6.4 Can I see counting event in Serial? ==
++== 5.4 Can I see counting event in Serial? ==
  (((
@@ -2074,7 +2074,7 @@
  User can run AT+DEBUG command to see the counting event in serial. If firmware too old and doesn't support AT+DEBUG. User can update to latest firmware first.
--== 6.5 Can i use point to point communication for LT-22222-L? ==
++== 5.5 Can i use point to point communication for LT-22222-L? ==
  Yes, please refer [[Point to Point Communication>>doc:Main. Point to Point Communication of LT-22222-L.WebHome]]  ，this is [[firmware>>https://github.com/dragino/LT-22222-L/releases]].
@@ -2083,7 +2083,7 @@
  )))
  (((
--== 6.6 Why does the relay output become the default and open relay after the lt22222 is powered off? ==
++== 5.6 Why does the relay output become the default and open relay after the lt22222 is powered off? ==
  If the device is not shut down, but directly powered off.
@@ -2095,7 +2095,7 @@
  After restart, the status before power failure will be read from flash.
--== 6.7 Can i set up LT-22222-L as a NC(Normal Close) Relay? ==
++== 5.7 Can i set up LT-22222-L as a NC(Normal Close) Relay? ==
  LT-22222-L built-in relay is NO (Normal Open). User can use an external relay to achieve Normal Close purpose. Diagram as below:
@@ -2104,18 +2104,18 @@
  [[image:image-20221006170630-1.png||height="610" width="945"]]
--== 6.8 Can LT22222-L save RO state? ==
++== 5.8 Can LT22222-L save RO state? ==
  Firmware version needs to be no less than 1.6.0.
--= 7. Trouble Shooting =
++= 6. Trouble Shooting =
  )))
  (((
  (((
--== 7.1 Downlink doesn't work, how to solve it? ==
++== 6.1 Downlink doesn't work, how to solve it? ==
  )))
@@ -2128,7 +2128,7 @@
  (((
--== 7.2 Have trouble to upload image. ==
++== 6.2 Have trouble to upload image. ==
  )))
@@ -2140,7 +2140,7 @@
  (((
--== 7.3 Why I can't join TTN in US915 /AU915 bands? ==
++== 6.3 Why I can't join TTN in US915 /AU915 bands? ==
  )))
@@ -2150,7 +2150,7 @@
  )))
--= 8. Order Info =
++= 7. Order Info =
  (% style="color:#4f81bd" %)**LT-22222-L-XXX:**
@@ -2169,7 +2169,7 @@
--= 9. Packing Info =
++= 8. Packing Info =
  **Package Includes**:
@@ -2179,7 +2179,6 @@
  * Bracket for controller x1
  * Program cable x 1
--
  **Dimension and weight**:
  * Device Size: 13.5 x 7 x 3 cm
@@ -2189,7 +2189,7 @@
--= 10. Support =
++= 9. Support =
  * (((
@@ -2202,7 +2202,7 @@
  )))
--= 11. Reference =
++= 10. Reference =
  * LT-22222-L: [[http:~~/~~/www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html]]
@@ -2209,4 +2209,5 @@
  * [[Datasheet, Document Base>>https://www.dropbox.com/sh/gxxmgks42tqfr3a/AACEdsj_mqzeoTOXARRlwYZ2a?dl=0]]
  * [[Hardware Source>>url:https://github.com/dragino/Lora/tree/master/LT/LT-33222-L/v1.0]]
++

Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Summary

Details

Applications

Navigation