Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Last modified by Mengting Qiu on 2025/06/04 18:42

From 102.2 to 102.1 From 102.4 to 102.3

From version 102.3

edited by Xiaoling
on 2022/10/29 09:54

Change comment: There is no comment for this version

To version 102.2

edited by Xiaoling
on 2022/10/29 09:42

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -923,9 +923,9 @@
  **(% style="color:blue" %)AT+TRIG1=a,b**
--**(% style="color:red" %)a :** (%%)Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge(for MOD=1).
++a : Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge(for MOD=1).
--**(% style="color:red" %)b :** (%%)delay timing.
++b : delay timing.
  **Example:**
@@ -934,11 +934,8 @@
  * (% style="color:#037691" %)**Downlink Payload (prefix 0x09 01 ):**
--* **(% style="color:blue" %)0x09 01 aa bb cc    ** (%%)    ~/~/ same as AT+TRIG1=aa,0x(bb cc)
++* **0x09 01 aa bb cc    **     ~/~/ same as AT+TRIG1=aa,0x(bb cc)
--
--
--
  ==== 3.4.2.8 Trigger2 – Set DI2 as trigger ====
@@ -946,12 +946,12 @@
  * (% style="color:#037691" %)**AT Command:**
--**(% style="color:blue" %)AT+TRIG2=a,b**
++**AT+TRIG2=a,b**
--**(% style="color:red" %)a :** (%%)Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge(for MOD=1).
++a : Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge(for MOD=1).
--**(% style="color:red" %)b :** (%%)delay timing.
++b : delay timing.
  **Example:**
@@ -961,7 +961,7 @@
  * (% style="color:#037691" %)**Downlink Payload (prefix 0x09 02 ):**
--**(% style="color:blue" %)0x09 02 aa bb cc   **  (%%)~/~/ same as AT+TRIG1=aa,0x(bb cc)
++**0x09 02 aa bb cc           **~/~/ same as AT+TRIG1=aa,0x(bb cc)
@@ -973,12 +973,12 @@
  * (% style="color:#037691" %)**AT Command**
--**(% style="color:blue" %)AT+ACLIM**
++**AT+ACLIM**
  * (% style="color:#037691" %)**Downlink Payload (prefix 0xAA 01 )**
--**(% style="color:blue" %)0x AA 01 aa bb cc dd ee ff gg hh        ** (%%)  ~/~/ same as AT+ACLIM See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
++**0x AA 01 aa bb cc dd ee ff gg hh        **   ~/~/ same as AT+ACLIM See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
@@ -990,12 +990,12 @@
  * (% style="color:#037691" %)**AT Command**
--**(% style="color:blue" %)AT+AVLIM    (%%)        See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]**
++**AT+AVLIM            See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]**
  * (% style="color:#037691" %)**Downlink Payload (prefix 0xAA 00 )**
--**(% style="color:blue" %)0x AA 00 aa bb cc dd ee ff gg hh    ** (%%) ~/~/ same as AT+AVLIM See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
++**0x AA 00 aa bb cc dd ee ff gg hh    ** ~/~/ same as AT+AVLIM See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
@@ -1007,12 +1007,12 @@
  * (% style="color:#037691" %)**AT Command**
--**(% style="color:blue" %)AT+ATDC=5        ** (%%)Device won't response the second trigger within 5 minute after the first trigger.
++**AT+ATDC=5        ** Device won't response the second trigger within 5 minute after the first trigger.
  * (% style="color:#037691" %)**Downlink Payload (prefix 0xAC )**
--**(% style="color:blue" %)0x AC aa bb   **(%%) ~/~/ same as AT+ATDC=0x(aa bb)   . Unit (min)
++**0x AC aa bb   ** ~/~/ same as AT+ATDC=0x(aa bb)   . Unit (min)
  (((
@@ -1032,7 +1032,7 @@
  * (% style="color:#037691" %)**Downlink Payload (prefix 0x02)**
--* **(% style="color:blue" %)0x02 aa bb cc     ** (%%)~/~/ Set DO1/DO2/DO3 output
++* **0x02 aa bb cc     **~/~/ Set DO1/DO2/DO3 output
  (((
  If payload = 0x02010001, while there is load between V+ and DOx, it means set DO1 to low, DO2 to high and DO3 to low.
@@ -1065,7 +1065,7 @@
  * (% style="color:#037691" %)**Downlink Payload (prefix 0xA9)**
--**(% style="color:blue" %)0xA9 aa bb cc     **(%%) ~/~/ Set DO1/DO2/DO3 output with time control
++**0xA9 aa bb cc     **~/~/ Set DO1/DO2/DO3 output with time control
  This is to control the digital output time of DO pin. Include four bytes:
@@ -1132,7 +1132,7 @@
  * (% style="color:#037691" %)**Downlink Payload (prefix 0x03):**
--**(% style="color:blue" %)0x03 aa bb     ** (%%)~/~/ Set RO1/RO2 output
++**0x03 aa bb     **~/~/ Set RO1/RO2 output
  (((
@@ -1162,7 +1162,7 @@
  * (% style="color:#037691" %)**Downlink Payload (prefix 0x05):**
--**(% style="color:blue" %)0x05 aa bb cc dd     ** (%%)~/~/ Set RO1/RO2 relay with time control
++**0x05 aa bb cc dd     **~/~/ Set RO1/RO2 relay with time control
  This is to control the relay output time of relay. Include four bytes:
@@ -1213,12 +1213,12 @@
  * (% style="color:#037691" %)**AT Command:**
--**(% style="color:blue" %)AT+VOLMAX   ** (%%)~/~/ See [[MOD4>>||anchor="H3.3.4AT2BMOD3D42CSingleDICounting2B1xVoltageCounting"]]
++**AT+VOLMAX   ** ~/~/ See [[MOD4>>||anchor="H3.3.4AT2BMOD3D42CSingleDICounting2B1xVoltageCounting"]]
  * (% style="color:#037691" %)**Downlink Payload (prefix 0xA5):**
--**(% style="color:blue" %)0xA5 aa bb cc   ** (%%)~/~/ Same as AT+VOLMAX=(aa bb),cc
++**0xA5 aa bb cc   **~/~/ Same as AT+VOLMAX=(aa bb),cc
@@ -1228,16 +1228,20 @@
  * (% style="color:#037691" %)**AT Command:**
--**(% style="color:blue" %)AT+SETCNT=aa,(bb cc dd ee) **
++**AT+SETCNT=aa,(bb cc dd ee) **
--**(% style="color:red" %)aa:**(%%) 1: Set count1; 2: Set count2; 3: Set AV1 count
++aa: 1: Set count1,
--**(% style="color:red" %)bb cc dd ee: **(%%)number to be set
++2: Set count2,
++3: Set AV1 count
++Bb cc dd ee: number to be set
++
++
  * (% style="color:#037691" %)**Downlink Payload (prefix 0xA8):**
--**(% style="color:blue" %)0x A8 aa bb cc dd ee     ** (%%)~/~/ same as AT+SETCNT=aa,(bb cc dd ee)
++**0x A8 aa bb cc dd ee     **~/~/ same as AT+SETCNT=aa,(bb cc dd ee)
@@ -1249,12 +1249,12 @@
  * (% style="color:#037691" %)**AT Command:**
--**(% style="color:blue" %)AT+CLRCOUNT **(%%) ~/~/ clear all counting
++**AT+CLRCOUNT ** ~/~/ clear all counting
  * (% style="color:#037691" %)**Downlink Payload (prefix 0xA6):**
--**(% style="color:blue" %)0x A6 01    ** (%%)~/~/ clear all counting
++**0x A6 01    ** ~/~/ clear all counting
@@ -1264,19 +1264,20 @@
  * (% style="color:#037691" %)**AT Command:**
--**(% style="color:blue" %)AT+COUTIME=60  **(%%)~/~/ Set save time to 60 seconds. Device will save the counting result in internal flash every 60 seconds. (min value: 30)
++**AT+COUTIME=60  **~/~/ Set save time to 60 seconds. Device will save the counting result in internal flash every 60 seconds. (min value: 30)
  * (% style="color:#037691" %)**Downlink Payload (prefix 0xA7):**
--**(% style="color:blue" %)0x A7 aa bb cc     ** (%%)~/~/ same as AT+COUTIME =aa bb cc,
++**0x A7 aa bb cc     **~/~/ same as AT+COUTIME =aa bb cc,
  (((
  range: aa bb cc:0 to 16777215,  (unit:second)
--)))
++
++)))
  ==== 3.4.2.20 Reset save DR DO state ====
@@ -1283,26 +1283,28 @@
  * (% style="color:#037691" %)**AT Command:**
--**(% style="color:blue" %)AT+RODORET=1  **(%%)~/~/ RODO will close when the device joining the network. (default)
++**AT+RODORET=1  **~/~/ RODO will close when the device joining the network. (default)
--**(% style="color:blue" %)AT+RODORET=0  **(%%)~/~/After the device is reset, the previously saved RODO state (only MOD2 to MOD5) is read, and its state is not changed when it is reconnected to the network.
++**AT+RODORET=0  **~/~/After the device is reset, the previously saved RODO state (only MOD2 to MOD5) is read, and its state is not changed when it is reconnected to the network.
  * (% style="color:#037691" %)**Downlink Payload (prefix 0xAD):**
--**(% style="color:blue" %)0x AD aa      ** (%%)~/~/ same as AT+RODORET =aa
++**0x AD aa      **~/~/ same as AT+RODORET =aa
++(((
++
  ==== 3.4.2.21 Encrypted payload ====
  * (% style="color:#037691" %)**AT Command:**
--**(% style="color:blue" %)AT+DECRYPT=1  ** (%%)~/~/ The payload is uploaded without encryption
++**AT+DECRYPT=1  **~/~/ The payload is uploaded without encryption
--**(% style="color:blue" %)AT+DECRYPT=0  **(%%)~/~/Encrypt when uploading payload (default)
++**AT+DECRYPT=0  **~/~/Encrypt when uploading payload (default)
@@ -1312,9 +1312,9 @@
  * (% style="color:#037691" %)**AT Command:**
--**(% style="color:blue" %)AT+GETSENSORVALUE=0  **(%%)~/~/ The serial port gets the reading of the current sensor
++**AT+GETSENSORVALUE=0  **~/~/ The serial port gets the reading of the current sensor
--**(% style="color:blue" %)AT+GETSENSORVALUE=1  **(%%)~/~/The serial port gets the current sensor reading and uploads it.
++**AT+GETSENSORVALUE=1  **~/~/The serial port gets the current sensor reading and uploads it.
@@ -1324,9 +1324,9 @@
  * (% style="color:#037691" %)**AT Command:**
--**(% style="color:blue" %)AT+DISFCNTCHECK=0  **(%%)~/~/ When the downlink packet count sent by the server is less than the node downlink packet count or exceeds 16384, the node will no longer receive downlink packets (default)
++**AT+DISFCNTCHECK=0  **~/~/ When the downlink packet count sent by the server is less than the node downlink packet count or exceeds 16384, the node will no longer receive downlink packets (default)
--**(% style="color:blue" %)AT+DISFCNTCHECK=1  **(%%)~/~/When the downlink packet count sent by the server is less than the node downlink packet count or exceeds 16384, the node resets the downlink packet count and keeps it consistent with the server downlink packet count.
++**AT+DISFCNTCHECK=1  **~/~/When the downlink packet count sent by the server is less than the node downlink packet count or exceeds 16384, the node resets the downlink packet count and keeps it consistent with the server downlink packet count.
@@ -1336,14 +1336,14 @@
  * (% style="color:#037691" %)**AT Command:**
--**(% style="color:blue" %)AT+DISMACANS=0**   (%%)  ~/~/ When the MACANS of the reply server plus the payload exceeds the maximum number of bytes of 11 bytes (DR0 of US915, DR2 of AS923, DR2 of AU195), the node will send a packet with a payload of 00 and a port of 4. (default)
++       **AT+DISMACANS=0**     ~/~/ When the MACANS of the reply server plus the payload exceeds the maximum number of bytes of 11 bytes (DR0 of US915, DR2 of AS923, DR2 of AU195), the node will send a packet with a payload of 00 and a port of 4. (default)
--**(% style="color:blue" %)AT+DISMACANS=1**  (%%)    ~/~/ When the MACANS of the reply server plus the payload exceeds the maximum number of bytes of the DR, the node will ignore the MACANS and not reply, and only upload the payload part.
++       **AT+DISMACANS=1**      ~/~/ When the MACANS of the reply server plus the payload exceeds the maximum number of bytes of the DR, the node will ignore the MACANS and not reply, and only upload the payload part.
  * (% style="color:#037691" %)**Downlink Payload **(%%)**:**
--**(% style="color:blue" %)0x21 00 01 **   (%%)      ~/~/ Set  the DISMACANS=1
++**0x21 00 01 **         ~/~/ Set  the DISMACANS=1
@@ -1353,7 +1353,7 @@
  * (% style="color:#037691" %)**AT Command**(%%)**:**
--**(% style="color:blue" %)AT+RPL=5**   (%%)  ~/~/ After receiving the package from the server, it will immediately upload the content of the package to the server, the port number is 100.
++       **AT+RPL=5**     ~/~/ After receiving the package from the server, it will immediately upload the content of the package to the server, the port number is 100.
  Example：**aa xx xx xx xx**         ~/~/ aa indicates whether the configuration has changed, 00 is yes, 01 is no; xx xx xx xx are the bytes sent.
@@ -1376,7 +1376,7 @@
  * (((
  (% style="color:#037691" %)**Downlink Payload**(%%)**:**
--**(% style="color:blue" %)26 01  ** (%%)  ~/~/  Downlink 26 01 can query device upload frequency, frequency band, software version number, TDC time.
++**26 01  **   ~/~/  Downlink 26 01 can query device upload frequency, frequency band, software version number, TDC time.
  )))

Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Summary

Details

Applications

Navigation