Wiki source code of LSE01-LoRaWAN Soil Moisture & EC Sensor User Manual

Version 31.26 by Xiaoling on 2022/06/07 10:23

version	line-number	content
4.2	1	(% style="text-align:center" %)
31.14	2	[[image:image-20220606151504-2.jpeg\|\|height="554" width="554"]]
1.1	3
	4
	5
31.17	6	Contents:
1.1	7
31.17	8	{{toc/}}
1.1	9
	10
	11
	12
31.17	13
	14
12.2	15	= 1. Introduction =
1.1	16
12.2	17	== 1.1 What is LoRaWAN Soil Moisture & EC Sensor ==
1.1	18
12.2	19	(((
	20	The Dragino LSE01 is a (% style="color:#4f81bd" %)LoRaWAN Soil Moisture & EC Sensor(%%) for IoT of Agriculture. It is designed to measure the soil moisture of saline-alkali soil and loamy soil. The soil sensor uses FDR method to calculate the soil moisture with the compensation from soil temperature and conductivity. It also has been calibrated in factory for Mineral soil type.
	21	)))
1.1	22
12.2	23	(((
	24	It detects (% style="color:#4f81bd" %)Soil Moisture(%%), (% style="color:#4f81bd" %)Soil Temperature(%%) and (% style="color:#4f81bd" %)Soil Conductivity(%%), and uploads the value via wireless to LoRaWAN IoT Server.
	25	)))
1.1	26
12.2	27	(((
4.2	28	The LoRa wireless technology used in LES01 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
12.2	29	)))
4.2	30
12.2	31	(((
	32	LES01 is powered by (% style="color:#4f81bd" %)4000mA or 8500mAh Li-SOCI2 battery(%%), It is designed for long term use up to 10 years.
	33	)))
4.2	34
12.2	35	(((
4.2	36	Each LES01 is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
12.2	37	)))
4.2	38
	39
12.2	40	[[image:1654503236291-817.png]]
4.2	41
	42
13.2	43	[[image:1654503265560-120.png]]
4.2	44
	45
	46
13.3	47	== 1.2 Features ==
	48
4.2	49	* LoRaWAN 1.0.3 Class A
	50	* Ultra low power consumption
	51	* Monitor Soil Moisture
	52	* Monitor Soil Temperature
	53	* Monitor Soil Conductivity
	54	* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
	55	* AT Commands to change parameters
	56	* Uplink on periodically
	57	* Downlink to change configure
	58	* IP66 Waterproof Enclosure
	59	* 4000mAh or 8500mAh Battery for long term use
	60
13.3	61	== 1.3 Specification ==
	62
4.2	63	Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
	64
14.2	65	[[image:image-20220606162220-5.png]]
	66
4.2	67
	68
14.3	69	== 1.4 Applications ==
4.2	70
	71	* Smart Agriculture
	72
15.6	73	(% class="wikigeneratedid" id="H200B1.5FirmwareChangelog" %)
	74
4.2	75
15.6	76	== 1.5 Firmware Change log ==
	77
	78
14.3	79	LSE01 v1.0 : Release
4.2	80
14.3	81
	82
	83	= 2. Configure LSE01 to connect to LoRaWAN network =
	84
	85	== 2.1 How it works ==
	86
15.3	87	(((
4.2	88	The LSE01 is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and power on the LSE0150. It will automatically join the network via OTAA and start to send the sensor value
15.3	89	)))
4.2	90
15.3	91	(((
15.4	92	In case you can’t set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>\|\|anchor="H3.UsingtheATCommands"]].
15.3	93	)))
4.2	94
	95
	96
14.4	97	== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==
4.2	98
	99	Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LG308>>url:http://www.dragino.com/products/lora/item/140-lg308.html]] as a LoRaWAN gateway in this example.
	100
	101
15.2	102	[[image:1654503992078-669.png]]
4.2	103
	104
	105	The LG308 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
	106
	107
	108	Step 1: Create a device in TTN with the OTAA keys from LSE01.
	109
	110	Each LSE01 is shipped with a sticker with the default device EUI as below:
	111
17.2	112	[[image:image-20220606163732-6.jpeg]]
4.2	113
	114	You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
	115
	116	Add APP EUI in the application
	117
	118
17.2	119	[[image:1654504596150-405.png]]
4.2	120
	121
	122
	123	Add APP KEY and DEV EUI
	124
18.2	125	[[image:1654504683289-357.png]]
4.2	126
	127
19.2	128
4.2	129	Step 2: Power on LSE01
	130
	131
	132	Put a Jumper on JP2 to power on the device. ( The Jumper must be in FLASH position).
	133
19.2	134	[[image:image-20220606163915-7.png]]
4.2	135
	136
	137	Step 3: The LSE01 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.
	138
20.2	139	[[image:1654504778294-788.png]]
4.2	140
	141
	142
20.3	143	== 2.3 Uplink Payload ==
4.2	144
20.3	145	=== 2.3.1 MOD~=0(Default Mode) ===
4.2	146
4.4	147	LSE01 will uplink payload via LoRaWAN with below payload format:
4.2	148
	149
	150	Uplink payload includes in total 11 bytes.
	151
	152
31.17	153	(% border="1" cellspacing="10" style="background-color:#f7faff; width:510px" %)
	154	\|=(((
4.2	155	Size
	156
	157	(bytes)
31.17	158	)))\|=(% style="width: 46px;" %)2\|=(% style="width: 160px;" %)2\|=(% style="width: 104px;" %)2\|=(% style="width: 126px;" %)2\|=(% style="width: 159px;" %)2\|=(% style="width: 114px;" %)1
31.18	159	\|Value\|(% style="width:46px" %)[[BAT>>\|\|anchor="H2.3.3BatteryInfo"]]\|(% style="width:160px" %)(((
4.2	160	Temperature
	161
	162	(Reserve, Ignore now)
31.19	163	)))\|(% style="width:104px" %)[[Soil Moisture>>\|\|anchor="H2.3.4SoilMoisture"]]\|(% style="width:126px" %)[[Soil Temperature>>\|\|anchor="H2.3.5SoilTemperature"]]\|(% style="width:159px" %)[[Soil Conductivity (EC)>>\|\|anchor="H2.3.6SoilConductivity28EC29"]]\|(% style="width:114px" %)(((
4.2	164	MOD & Digital Interrupt
	165
	166	(Optional)
	167	)))
	168
22.2	169	[[image:1654504881641-514.png]]
4.2	170
	171
	172
22.2	173	=== 2.3.2 MOD~=1(Original value) ===
	174
4.2	175	This mode can get the original AD value of moisture and original conductivity (with temperature drift compensation).
	176
31.17	177	(% border="1" cellspacing="10" style="background-color:#f7faff; width:510px" %)
	178	\|=(((
4.2	179	Size
	180
	181	(bytes)
31.17	182	)))\|=2\|=2\|=2\|=2\|=2\|=1
31.20	183	\|Value\|[[BAT>>\|\|anchor="H2.3.3BatteryInfo"]]\|(((
4.2	184	Temperature
	185
	186	(Reserve, Ignore now)
31.21	187	)))\|[[Soil Moisture>>\|\|anchor="H2.3.4SoilMoisture"]]\|[[Soil Temperature>>\|\|anchor="H2.3.5SoilTemperature"]]\|[[Soil Conductivity (EC)>>\|\|anchor="H2.3.6SoilConductivity28EC29"]](raw)\|(((
4.2	188	MOD & Digital Interrupt
	189
	190	(Optional)
	191	)))
	192
22.2	193	[[image:1654504907647-967.png]]
4.2	194
	195
22.2	196
	197	=== 2.3.3 Battery Info ===
	198
4.2	199	Check the battery voltage for LSE01.
	200
	201	Ex1: 0x0B45 = 2885mV
	202
	203	Ex2: 0x0B49 = 2889mV
	204
	205
	206
22.3	207	=== 2.3.4 Soil Moisture ===
4.2	208
	209	Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
	210
22.4	211	For example, if the data you get from the register is __0x05 0xDC__, the moisture content in the soil is
4.2	212
	213
22.4	214	(% style="color:#4f81bd" %)05DC(H) = 1500(D) /100 = 15%.
4.2	215
22.4	216
4.2	217
22.5	218	=== 2.3.5 Soil Temperature ===
	219
4.2	220	Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is 0x09 0xEC, the temperature content in the soil is
	221
	222	Example:
	223
	224	If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/100 = 2.61 °C
	225
	226	If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/100 = -1.29 °C
	227
	228
	229
22.6	230	=== 2.3.6 Soil Conductivity (EC) ===
	231
23.2	232	(((
	233	Obtain (% style="color:#4f81bd" %)__soluble salt concentration__(%%) in soil or (% style="color:#4f81bd" %)__soluble ion concentration in liquid fertilizer__(%%) or (% style="color:#4f81bd" %)__planting medium__(%%). The value range of the register is 0 - 20000(Decimal)( Can be greater than 20000).
	234	)))
4.2	235
23.2	236	(((
4.2	237	For example, if the data you get from the register is 0x00 0xC8, the soil conductivity is 00C8(H) = 200(D) = 200 uS/cm.
23.2	238	)))
4.2	239
23.2	240	(((
4.2	241	Generally, the EC value of irrigation water is less than 800uS / cm.
23.2	242	)))
4.2	243
23.2	244	(((
	245
	246	)))
4.2	247
23.2	248	(((
	249
	250	)))
	251
	252	=== 2.3.7 MOD ===
	253
4.2	254	Firmware version at least v2.1 supports changing mode.
	255
	256	For example, bytes[10]=90
	257
	258	mod=(bytes[10]>>7)&0x01=1.
	259
	260
31.23	261	Downlink Command:
4.2	262
	263	If payload = 0x0A00, workmode=0
	264
	265	If payload = 0x0A01, workmode=1
	266
	267
	268
23.2	269	=== 2.3.8 Decode payload in The Things Network ===
	270
4.2	271	While using TTN network, you can add the payload format to decode the payload.
	272
	273
23.2	274	[[image:1654505570700-128.png]]
4.2	275
	276	The payload decoder function for TTN is here:
	277
	278	LSE01 TTN Payload Decoder: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/]]
	279
	280
23.3	281	== 2.4 Uplink Interval ==
4.2	282
31.26	283	The LSE01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome\|\|anchor="H4.1ChangeUplinkInterval"]]
4.2	284
	285
	286
24.2	287	== 2.5 Downlink Payload ==
	288
4.2	289	By default, LSE50 prints the downlink payload to console port.
	290
24.2	291	[[image:image-20220606165544-8.png]]
4.2	292
24.2	293
26.2	294	Examples:
4.2	295
	296
26.2	297	* Set TDC
4.2	298
	299	If the payload=0100003C, it means set the END Node’s TDC to 0x00003C=60(S), while type code is 01.
	300
	301	Payload: 01 00 00 1E TDC=30S
	302
	303	Payload: 01 00 00 3C TDC=60S
	304
	305
26.2	306	* Reset
4.2	307
	308	If payload = 0x04FF, it will reset the LSE01
	309
	310
26.2	311	* CFM
4.2	312
	313	Downlink Payload: 05000001, Set AT+CFM=1 or 05000000 , set AT+CFM=0
	314
	315
26.2	316
	317	== 2.6 Show Data in DataCake IoT Server ==
	318
4.2	319	[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
	320
	321
	322	Step 1: Be sure that your device is programmed and properly connected to the network at this time.
	323
	324	Step 2: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
	325
	326
26.2	327	[[image:1654505857935-743.png]]
4.2	328
	329
26.2	330	[[image:1654505874829-548.png]]
4.2	331
	332	Step 3: Create an account or log in Datacake.
	333
	334	Step 4: Search the LSE01 and add DevEUI.
	335
	336
27.2	337	[[image:1654505905236-553.png]]
4.2	338
	339
	340	After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
	341
28.2	342	[[image:1654505925508-181.png]]
4.2	343
	344
	345
28.4	346	== 2.7 Frequency Plans ==
4.2	347
	348	The LSE01 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
	349
	350
28.5	351	=== 2.7.1 EU863-870 (EU868) ===
4.2	352
28.5	353	(% style="color:#037691" %) Uplink:
	354
4.2	355	868.1 - SF7BW125 to SF12BW125
	356
	357	868.3 - SF7BW125 to SF12BW125 and SF7BW250
	358
	359	868.5 - SF7BW125 to SF12BW125
	360
	361	867.1 - SF7BW125 to SF12BW125
	362
	363	867.3 - SF7BW125 to SF12BW125
	364
	365	867.5 - SF7BW125 to SF12BW125
	366
	367	867.7 - SF7BW125 to SF12BW125
	368
	369	867.9 - SF7BW125 to SF12BW125
	370
	371	868.8 - FSK
	372
	373
28.5	374	(% style="color:#037691" %) Downlink:
4.2	375
	376	Uplink channels 1-9 (RX1)
	377
	378	869.525 - SF9BW125 (RX2 downlink only)
	379
	380
	381
28.5	382	=== 2.7.2 US902-928(US915) ===
	383
4.2	384	Used in USA, Canada and South America. Default use CHE=2
	385
28.5	386	(% style="color:#037691" %)Uplink:
4.2	387
	388	903.9 - SF7BW125 to SF10BW125
	389
	390	904.1 - SF7BW125 to SF10BW125
	391
	392	904.3 - SF7BW125 to SF10BW125
	393
	394	904.5 - SF7BW125 to SF10BW125
	395
	396	904.7 - SF7BW125 to SF10BW125
	397
	398	904.9 - SF7BW125 to SF10BW125
	399
	400	905.1 - SF7BW125 to SF10BW125
	401
	402	905.3 - SF7BW125 to SF10BW125
	403
	404
28.5	405	(% style="color:#037691" %)Downlink:
4.2	406
	407	923.3 - SF7BW500 to SF12BW500
	408
	409	923.9 - SF7BW500 to SF12BW500
	410
	411	924.5 - SF7BW500 to SF12BW500
	412
	413	925.1 - SF7BW500 to SF12BW500
	414
	415	925.7 - SF7BW500 to SF12BW500
	416
	417	926.3 - SF7BW500 to SF12BW500
	418
	419	926.9 - SF7BW500 to SF12BW500
	420
	421	927.5 - SF7BW500 to SF12BW500
	422
	423	923.3 - SF12BW500(RX2 downlink only)
	424
	425
	426
28.5	427	=== 2.7.3 CN470-510 (CN470) ===
	428
4.2	429	Used in China, Default use CHE=1
	430
28.5	431	(% style="color:#037691" %)Uplink:
4.2	432
	433	486.3 - SF7BW125 to SF12BW125
	434
	435	486.5 - SF7BW125 to SF12BW125
	436
	437	486.7 - SF7BW125 to SF12BW125
	438
	439	486.9 - SF7BW125 to SF12BW125
	440
	441	487.1 - SF7BW125 to SF12BW125
	442
	443	487.3 - SF7BW125 to SF12BW125
	444
	445	487.5 - SF7BW125 to SF12BW125
	446
	447	487.7 - SF7BW125 to SF12BW125
	448
	449
28.5	450	(% style="color:#037691" %)Downlink:
4.2	451
	452	506.7 - SF7BW125 to SF12BW125
	453
	454	506.9 - SF7BW125 to SF12BW125
	455
	456	507.1 - SF7BW125 to SF12BW125
	457
	458	507.3 - SF7BW125 to SF12BW125
	459
	460	507.5 - SF7BW125 to SF12BW125
	461
	462	507.7 - SF7BW125 to SF12BW125
	463
	464	507.9 - SF7BW125 to SF12BW125
	465
	466	508.1 - SF7BW125 to SF12BW125
	467
	468	505.3 - SF12BW125 (RX2 downlink only)
	469
	470
	471
28.5	472	=== 2.7.4 AU915-928(AU915) ===
	473
4.2	474	Default use CHE=2
	475
28.5	476	(% style="color:#037691" %)Uplink:
4.2	477
	478	916.8 - SF7BW125 to SF12BW125
	479
	480	917.0 - SF7BW125 to SF12BW125
	481
	482	917.2 - SF7BW125 to SF12BW125
	483
	484	917.4 - SF7BW125 to SF12BW125
	485
	486	917.6 - SF7BW125 to SF12BW125
	487
	488	917.8 - SF7BW125 to SF12BW125
	489
	490	918.0 - SF7BW125 to SF12BW125
	491
	492	918.2 - SF7BW125 to SF12BW125
	493
	494
28.5	495	(% style="color:#037691" %)Downlink:
4.2	496
	497	923.3 - SF7BW500 to SF12BW500
	498
	499	923.9 - SF7BW500 to SF12BW500
	500
	501	924.5 - SF7BW500 to SF12BW500
	502
	503	925.1 - SF7BW500 to SF12BW500
	504
	505	925.7 - SF7BW500 to SF12BW500
	506
	507	926.3 - SF7BW500 to SF12BW500
	508
	509	926.9 - SF7BW500 to SF12BW500
	510
	511	927.5 - SF7BW500 to SF12BW500
	512
	513	923.3 - SF12BW500(RX2 downlink only)
	514
	515
28.6	516
	517	=== 2.7.5 AS920-923 & AS923-925 (AS923) ===
	518
28.7	519	(% style="color:#037691" %)Default Uplink channel:
4.2	520
	521	923.2 - SF7BW125 to SF10BW125
	522
	523	923.4 - SF7BW125 to SF10BW125
	524
	525
28.7	526	(% style="color:#037691" %)Additional Uplink Channel:
4.2	527
	528	(OTAA mode, channel added by JoinAccept message)
	529
28.7	530	(% style="color:#037691" %)AS920~~AS923 for Japan, Malaysia, Singapore:
4.2	531
	532	922.2 - SF7BW125 to SF10BW125
	533
	534	922.4 - SF7BW125 to SF10BW125
	535
	536	922.6 - SF7BW125 to SF10BW125
	537
	538	922.8 - SF7BW125 to SF10BW125
	539
	540	923.0 - SF7BW125 to SF10BW125
	541
	542	922.0 - SF7BW125 to SF10BW125
	543
	544
28.7	545	(% style="color:#037691" %)AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam:
4.2	546
	547	923.6 - SF7BW125 to SF10BW125
	548
	549	923.8 - SF7BW125 to SF10BW125
	550
	551	924.0 - SF7BW125 to SF10BW125
	552
	553	924.2 - SF7BW125 to SF10BW125
	554
	555	924.4 - SF7BW125 to SF10BW125
	556
	557	924.6 - SF7BW125 to SF10BW125
	558
	559
28.7	560	(% style="color:#037691" %) Downlink:
4.2	561
	562	Uplink channels 1-8 (RX1)
	563
	564	923.2 - SF10BW125 (RX2)
	565
	566
	567
28.7	568	=== 2.7.6 KR920-923 (KR920) ===
	569
4.2	570	Default channel:
	571
	572	922.1 - SF7BW125 to SF12BW125
	573
	574	922.3 - SF7BW125 to SF12BW125
	575
	576	922.5 - SF7BW125 to SF12BW125
	577
	578
28.7	579	(% style="color:#037691" %)Uplink: (OTAA mode, channel added by JoinAccept message)
4.2	580
	581	922.1 - SF7BW125 to SF12BW125
	582
	583	922.3 - SF7BW125 to SF12BW125
	584
	585	922.5 - SF7BW125 to SF12BW125
	586
	587	922.7 - SF7BW125 to SF12BW125
	588
	589	922.9 - SF7BW125 to SF12BW125
	590
	591	923.1 - SF7BW125 to SF12BW125
	592
	593	923.3 - SF7BW125 to SF12BW125
	594
	595
28.7	596	(% style="color:#037691" %)Downlink:
4.2	597
	598	Uplink channels 1-7(RX1)
	599
	600	921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
	601
	602
	603
28.7	604	=== 2.7.7 IN865-867 (IN865) ===
4.2	605
28.7	606	(% style="color:#037691" %) Uplink:
	607
4.2	608	865.0625 - SF7BW125 to SF12BW125
	609
	610	865.4025 - SF7BW125 to SF12BW125
	611
	612	865.9850 - SF7BW125 to SF12BW125
	613
	614
28.7	615	(% style="color:#037691" %) Downlink:
4.2	616
	617	Uplink channels 1-3 (RX1)
	618
	619	866.550 - SF10BW125 (RX2)
	620
	621
	622
28.7	623
	624	== 2.8 LED Indicator ==
	625
4.2	626	The LSE01 has an internal LED which is to show the status of different state.
	627
	628	* Blink once when device power on.
	629	* Solid ON for 5 seconds once device successful Join the network.
	630	* Blink once when device transmit a packet.
	631
28.8	632	== 2.9 Installation in Soil ==
	633
4.2	634	Measurement the soil surface
	635
	636
29.2	637	[[image:1654506634463-199.png]]
4.2	638
29.2	639	(((
31.8	640	(((
4.2	641	Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting.
29.2	642	)))
31.8	643	)))
4.2	644
	645
30.2	646	[[image:1654506665940-119.png]]
4.2	647
31.8	648	(((
4.2	649	Dig a hole with diameter > 20CM.
31.8	650	)))
4.2	651
31.8	652	(((
4.2	653	Horizontal insert the probe to the soil and fill the hole for long term measurement.
31.8	654	)))
4.2	655
	656
30.3	657	== 2.10 Firmware Change Log ==
4.2	658
31.7	659	(((
4.2	660	Firmware download link:
31.7	661	)))
4.2	662
31.7	663	(((
4.2	664	[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
31.7	665	)))
4.2	666
31.7	667	(((
	668
	669	)))
4.2	670
31.7	671	(((
30.4	672	Firmware Upgrade Method: [[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]
31.7	673	)))
4.2	674
31.7	675	(((
	676
	677	)))
4.2	678
31.7	679	(((
4.2	680	V1.0.
31.7	681	)))
4.2	682
31.7	683	(((
4.2	684	Release
31.7	685	)))
4.2	686
	687
31.2	688	== 2.11 Battery Analysis ==
4.2	689
31.2	690	=== 2.11.1 Battery Type ===
4.2	691
31.6	692	(((
4.2	693	The LSE01 battery is a combination of a 4000mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
31.6	694	)))
4.2	695
31.6	696	(((
4.2	697	The battery is designed to last for more than 5 years for the LSN50.
31.6	698	)))
4.2	699
31.2	700	(((
31.6	701	(((
31.2	702	The battery-related documents are as below:
	703	)))
31.6	704	)))
4.2	705
31.2	706	* (((
	707	[[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
4.2	708	)))
31.2	709	* (((
	710	[[Lithium-Thionyl Chloride Battery datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
	711	)))
	712	* (((
	713	[[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
	714	)))
4.2	715
31.2	716	[[image:image-20220606171726-9.png]]
4.2	717
	718
	719
31.2	720	=== 2.11.2 Battery Note ===
4.2	721
31.3	722	(((
4.2	723	The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
31.3	724	)))
4.2	725
	726
	727
31.2	728	=== 2.11.3 Replace the battery ===
	729
31.3	730	(((
4.2	731	If Battery is lower than 2.7v, user should replace the battery of LSE01.
31.3	732	)))
4.2	733
31.3	734	(((
4.2	735	You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
31.3	736	)))
4.2	737
31.3	738	(((
4.2	739	The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can’t find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
31.3	740	)))
4.2	741
	742
	743
9.2	744	= 3. Using the AT Commands =
4.2	745
9.2	746	== 3.1 Access AT Commands ==
	747
11.4	748
4.2	749	LSE01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSE01 for using AT command, as below.
	750
9.2	751	[[image:1654501986557-872.png]]
4.2	752
	753
	754	Or if you have below board, use below connection:
	755
	756
11.2	757	[[image:1654502005655-729.png]]
4.2	758
	759
	760
11.2	761	In the PC, you need to set the serial baud rate to (% style="color:green" %)9600(%%) to access the serial console for LSE01. LSE01 will output system info once power on as below:
4.2	762
	763
11.2	764	[[image:1654502050864-459.png]]
4.2	765
	766
	767	Below are the available commands, a more detailed AT Command manual can be found at [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]
	768
	769
11.4	770	(% style="background-color:#dcdcdc" %)AT+<CMD>=?AT+<CMD>? (%%) : Help on <CMD>
4.2	771
11.4	772	(% style="background-color:#dcdcdc" %)AT+<CMD>=?AT+<CMD> (%%) : Run <CMD>
4.2	773
11.4	774	(% style="background-color:#dcdcdc" %)AT+<CMD>=?AT+<CMD>=<value>(%%) : Set the value
4.2	775
11.4	776	(% style="background-color:#dcdcdc" %)AT+<CMD>=?AT+<CMD>=?(%%) : Get the value
4.2	777
	778
11.6	779	(% style="color:#037691" %)General Commands(%%)
4.2	780
11.6	781	(% style="background-color:#dcdcdc" %)AT(%%) : Attention
4.2	782
11.6	783	(% style="background-color:#dcdcdc" %)AT?(%%) : Short Help
4.2	784
11.6	785	(% style="background-color:#dcdcdc" %)ATZ(%%) : MCU Reset
4.2	786
11.6	787	(% style="background-color:#dcdcdc" %)AT+TDC(%%) : Application Data Transmission Interval
4.2	788
	789
11.4	790	(% style="color:#037691" %)Keys, IDs and EUIs management
4.2	791
11.6	792	(% style="background-color:#dcdcdc" %)AT+APPEUI(%%) : Application EUI
4.2	793
11.6	794	(% style="background-color:#dcdcdc" %)AT+APPKEY(%%) : Application Key
4.2	795
11.6	796	(% style="background-color:#dcdcdc" %)AT+APPSKEY(%%) : Application Session Key
4.2	797
11.6	798	(% style="background-color:#dcdcdc" %)AT+DADDR(%%) : Device Address
4.2	799
11.6	800	(% style="background-color:#dcdcdc" %)AT+DEUI(%%) : Device EUI
4.2	801
11.6	802	(% style="background-color:#dcdcdc" %)AT+NWKID(%%) : Network ID (You can enter this command change only after successful network connection)
4.2	803
11.6	804	(% style="background-color:#dcdcdc" %)AT+NWKSKEY(%%) : Network Session Key Joining and sending date on LoRa network
4.2	805
11.6	806	(% style="background-color:#dcdcdc" %)AT+CFM(%%) : Confirm Mode
4.2	807
11.6	808	(% style="background-color:#dcdcdc" %)AT+CFS(%%) : Confirm Status
4.2	809
11.6	810	(% style="background-color:#dcdcdc" %)AT+JOIN(%%) : Join LoRa? Network
4.2	811
11.6	812	(% style="background-color:#dcdcdc" %)AT+NJM(%%) : LoRa? Network Join Mode
4.2	813
11.6	814	(% style="background-color:#dcdcdc" %)AT+NJS(%%) : LoRa? Network Join Status
4.2	815
11.6	816	(% style="background-color:#dcdcdc" %)AT+RECV(%%) : Print Last Received Data in Raw Format
4.2	817
11.6	818	(% style="background-color:#dcdcdc" %)AT+RECVB(%%) : Print Last Received Data in Binary Format
4.2	819
11.6	820	(% style="background-color:#dcdcdc" %)AT+SEND(%%) : Send Text Data
4.2	821
11.6	822	(% style="background-color:#dcdcdc" %)AT+SENB(%%) : Send Hexadecimal Data
4.2	823
	824
11.4	825	(% style="color:#037691" %)LoRa Network Management
4.2	826
11.6	827	(% style="background-color:#dcdcdc" %)AT+ADR(%%) : Adaptive Rate
4.2	828
11.6	829	(% style="background-color:#dcdcdc" %)AT+CLASS(%%) : LoRa Class(Currently only support class A
4.2	830
11.6	831	(% style="background-color:#dcdcdc" %)AT+DCS(%%) : Duty Cycle Setting
4.2	832
11.6	833	(% style="background-color:#dcdcdc" %)AT+DR(%%) : Data Rate (Can Only be Modified after ADR=0)
4.2	834
11.6	835	(% style="background-color:#dcdcdc" %)AT+FCD(%%) : Frame Counter Downlink
4.2	836
11.6	837	(% style="background-color:#dcdcdc" %)AT+FCU(%%) : Frame Counter Uplink
4.2	838
11.6	839	(% style="background-color:#dcdcdc" %)AT+JN1DL(%%) : Join Accept Delay1
4.2	840
11.6	841	(% style="background-color:#dcdcdc" %)AT+JN2DL(%%) : Join Accept Delay2
4.2	842
11.6	843	(% style="background-color:#dcdcdc" %)AT+PNM(%%) : Public Network Mode
4.2	844
11.6	845	(% style="background-color:#dcdcdc" %)AT+RX1DL(%%) : Receive Delay1
4.2	846
11.6	847	(% style="background-color:#dcdcdc" %)AT+RX2DL(%%) : Receive Delay2
4.2	848
11.6	849	(% style="background-color:#dcdcdc" %)AT+RX2DR(%%) : Rx2 Window Data Rate
4.2	850
11.6	851	(% style="background-color:#dcdcdc" %)AT+RX2FQ(%%) : Rx2 Window Frequency
4.2	852
11.6	853	(% style="background-color:#dcdcdc" %)AT+TXP(%%) : Transmit Power
4.2	854
11.6	855	(% style="background-color:#dcdcdc" %)AT+ MOD(%%) : Set work mode
4.2	856
	857
11.4	858	(% style="color:#037691" %)Information
4.2	859
11.6	860	(% style="background-color:#dcdcdc" %)AT+RSSI(%%) : RSSI of the Last Received Packet
4.2	861
11.6	862	(% style="background-color:#dcdcdc" %)AT+SNR(%%) : SNR of the Last Received Packet
4.2	863
11.6	864	(% style="background-color:#dcdcdc" %)AT+VER(%%) : Image Version and Frequency Band
4.2	865
11.6	866	(% style="background-color:#dcdcdc" %)AT+FDR(%%) : Factory Data Reset
4.2	867
11.6	868	(% style="background-color:#dcdcdc" %)AT+PORT(%%) : Application Port
4.2	869
11.6	870	(% style="background-color:#dcdcdc" %)AT+CHS(%%) : Get or Set Frequency (Unit: Hz) for Single Channel Mode
4.2	871
11.6	872	(% style="background-color:#dcdcdc" %)AT+CHE(%%) : Get or Set eight channels mode, Only for US915, AU915, CN470
4.2	873
	874
6.3	875	= 4. FAQ =
4.2	876
6.3	877	== 4.1 How to change the LoRa Frequency Bands/Region? ==
	878
31.24	879	You can follow the instructions for [[how to upgrade image>>\|\|anchor="H2.10200BFirmwareChangeLog"]].
4.2	880	When downloading the images, choose the required image file for download.
	881
	882
8.3	883	How to set up LSE01 to work in 8 channel mode By default, the frequency bands US915, AU915, CN470 work in 72 frequencies. Many gateways are 8 channel gateways, and in this case, the OTAA join time and uplink schedule is long and unpredictable while the end node is hopping in 72 frequencies.
4.2	884
	885
	886	You can configure the end node to work in 8 channel mode by using the AT+CHE command. The 500kHz channels are always included for OTAA.
	887
	888
	889	For example, in US915 band, the frequency table is as below. By default, the end node will use all channels (0~~71) for OTAA Join process. After the OTAA Join, the end node will use these all channels (0~~71) to send uplink packets.
	890
8.2	891	[[image:image-20220606154726-3.png]]
4.2	892
	893	When you use the TTN network, the US915 frequency bands use are:
	894
	895	* 903.9 - SF7BW125 to SF10BW125
	896	* 904.1 - SF7BW125 to SF10BW125
	897	* 904.3 - SF7BW125 to SF10BW125
	898	* 904.5 - SF7BW125 to SF10BW125
	899	* 904.7 - SF7BW125 to SF10BW125
	900	* 904.9 - SF7BW125 to SF10BW125
	901	* 905.1 - SF7BW125 to SF10BW125
	902	* 905.3 - SF7BW125 to SF10BW125
	903	* 904.6 - SF8BW500
	904
	905	Because the end node is now hopping in 72 frequency, it makes it difficult for the devices to Join the TTN network and uplink data. To solve this issue, you can access the device via the AT commands and run:
	906
8.3	907	(% class="box infomessage" %)
	908	(((
4.2	909	AT+CHE=2
8.3	910	)))
4.2	911
8.3	912	(% class="box infomessage" %)
	913	(((
4.2	914	ATZ
8.3	915	)))
4.2	916
	917	to set the end node to work in 8 channel mode. The device will work in Channel 8-15 & 64-71 for OTAA, and channel 8-15 for Uplink.
	918
	919
	920	The AU915 band is similar. Below are the AU915 Uplink Channels.
	921
8.2	922	[[image:image-20220606154825-4.png]]
4.2	923
	924
	925
4.8	926	= 5. Trouble Shooting =
4.2	927
4.9	928	== 5.1 Why I can’t join TTN in US915 / AU915 bands? ==
	929
4.11	930	It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main.LoRaWAN Communication Debug.WebHome\|\|anchor="H2.NoticeofUS9152FCN4702FAU915Frequencyband"]] section above for details.
4.2	931
	932
4.10	933	== 5.2 AT Command input doesn’t work ==
4.2	934
6.2	935	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)ENTER(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)ENTER(%%) while press the send key, user need to add ENTER in their string.
4.2	936
	937
4.10	938	== 5.3 Device rejoin in at the second uplink packet ==
4.2	939
6.2	940	(% style="color:#4f81bd" %)Issue describe as below:
4.2	941
6.2	942	[[image:1654500909990-784.png]]
4.2	943
	944
6.2	945	(% style="color:#4f81bd" %)Cause for this issue:
4.2	946
	947	The fuse on LSE01 is not large enough, some of the soil probe require large current up to 5v 800mA, in a short pulse. When this happen, it cause the device reboot so user see rejoin.
	948
	949
6.2	950	(% style="color:#4f81bd" %)Solution:
4.2	951
	952	All new shipped LSE01 after 2020-May-30 will have this to fix. For the customer who see this issue, please bypass the fuse as below:
	953
6.2	954	[[image:1654500929571-736.png]]
4.2	955
4.7	956
4.4	957	= 6. Order Info =
4.2	958
	959
4.6	960	Part Number: (% style="color:#4f81bd" %)LSE01-XX-YY
4.2	961
	962
4.6	963	(% style="color:#4f81bd" %)XX(%%): The default frequency band
4.2	964
4.4	965	* (% style="color:red" %)AS923(%%): LoRaWAN AS923 band
	966	* (% style="color:red" %)AU915(%%): LoRaWAN AU915 band
	967	* (% style="color:red" %)EU433(%%): LoRaWAN EU433 band
	968	* (% style="color:red" %)EU868(%%): LoRaWAN EU868 band
	969	* (% style="color:red" %)KR920(%%): LoRaWAN KR920 band
	970	* (% style="color:red" %)US915(%%): LoRaWAN US915 band
4.5	971	* (% style="color:red" %)IN865(%%): LoRaWAN IN865 band
4.4	972	* (% style="color:red" %)CN470(%%): LoRaWAN CN470 band
4.2	973
4.4	974	(% style="color:#4f81bd" %)YY(%%): Battery Option
4.2	975
4.4	976	* (% style="color:red" %)4(%%): 4000mAh battery
	977	* (% style="color:red" %)8(%%): 8500mAh battery
4.2	978
31.10	979	(% class="wikigeneratedid" %)
	980	(((
	981
	982	)))
	983
4.3	984	= 7. Packing Info =
4.2	985
4.3	986	(((
4.2	987	Package Includes:
4.3	988	)))
4.2	989
4.3	990	* (((
	991	LSE01 LoRaWAN Soil Moisture & EC Sensor x 1
	992	)))
4.2	993
4.3	994	(((
	995
	996	)))
4.2	997
4.3	998	(((
4.2	999	Dimension and weight:
4.3	1000	)))
4.2	1001
4.3	1002	* (((
	1003	Device Size: cm
	1004	)))
	1005	* (((
	1006	Device Weight: g
	1007	)))
	1008	* (((
	1009	Package Size / pcs : cm
	1010	)))
	1011	* (((
	1012	Weight / pcs : g
31.11	1013
	1014
	1015
4.3	1016	)))
4.2	1017
4.3	1018	= 8. Support =
4.2	1019
	1020	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
	1021	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
	1022
27.2	1023

Wiki source code of LSE01-LoRaWAN Soil Moisture & EC Sensor User Manual

Applications