Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -68,8 +68,6 @@
68	68	* IP66 Waterproof Enclosure
69	69	* 4000mAh or 8500mAh Battery for long term use
70	70
71		-
72		-
73	73	== 1.3 Specification ==
74	74
75	75	Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
...	...	@@ -179,8 +179,6 @@
179	179	(Optional)
180	180	)))
181	181
182		-
183		-
184	184	=== 2.3.2 MOD~=1(Original value) ===
185	185
186	186	This mode can get the original AD value of moisture and original conductivity (with temperature drift compensation).
...	...	@@ -201,8 +201,6 @@
201	201	(Optional)
202	202	)))
203	203
204		-
205		-
206	206	=== 2.3.3 Battery Info ===
207	207
208	208	(((
...	...	@@ -314,7 +314,6 @@
314	314	)))
315	315
316	316
317		-
318	318	== 2.4 Uplink Interval ==
319	319
320	320	The LSE01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H4.1ChangeUplinkInterval"]]
...	...	@@ -323,7 +323,7 @@
323	323
324	324	== 2.5 Downlink Payload ==
325	325
326		-By default, LSE01 prints the downlink payload to console port.
	319	+By default, LSE50 prints the downlink payload to console port.
327	327
328	328	[[image:image-20220606165544-8.png]]
329	329
...	...	@@ -341,7 +341,7 @@
341	341	)))
342	342
343	343	(((
344		-If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01.
	337	+If the payload=0100003C, it means set the END Node’s TDC to 0x00003C=60(S), while type code is 01.
345	345	)))
346	346
347	347	(((
...	...	@@ -697,8 +697,6 @@
697	697	* Blink once when device transmit a packet.
698	698
699	699
700		-
701		-
702	702	== 2.9 Installation in Soil ==
703	703
704	704	**Measurement the soil surface**
...	...	@@ -803,11 +803,11 @@
803	803	)))
804	804
805	805	(((
806		-You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won't be voltage drop between battery and main board.
	797	+You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
807	807	)))
808	808
809	809	(((
810		-The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can't find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
	801	+The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can’t find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
811	811	)))
812	812
813	813
...	...	@@ -1080,8 +1080,6 @@
1080	1080	(% class="wikigeneratedid" %)
1081	1081	(((
1082	1082
1083		-
1084		-
1085	1085	)))
1086	1086
1087	1087	= 7. Packing Info =
...	...	@@ -1114,7 +1114,6 @@
1114	1114	* (((
1115	1115	Weight / pcs : g
1116	1116
1117		-
1118	1118
1119	1119	)))
1120	1120