Changes for page LSE01-LoRaWAN Soil Moisture & EC Sensor User Manual
Last modified by Bei Jinggeng on 2024/08/02 16:47
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -69,7 +69,6 @@ 69 69 * 4000mAh or 8500mAh Battery for long term use 70 70 71 71 72 - 73 73 == 1.3 Specification == 74 74 75 75 Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height. ... ... @@ -180,7 +180,6 @@ 180 180 ))) 181 181 182 182 183 - 184 184 === 2.3.2 MOD~=1(Original value) === 185 185 186 186 This mode can get the original AD value of moisture and original conductivity (with temperature drift compensation). ... ... @@ -202,7 +202,6 @@ 202 202 ))) 203 203 204 204 205 - 206 206 === 2.3.3 Battery Info === 207 207 208 208 ((( ... ... @@ -314,7 +314,6 @@ 314 314 ))) 315 315 316 316 317 - 318 318 == 2.4 Uplink Interval == 319 319 320 320 The LSE01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H4.1ChangeUplinkInterval"]] ... ... @@ -323,7 +323,7 @@ 323 323 324 324 == 2.5 Downlink Payload == 325 325 326 -By default, LSE0 1prints the downlink payload to console port.322 +By default, LSE50 prints the downlink payload to console port. 327 327 328 328 [[image:image-20220606165544-8.png]] 329 329 ... ... @@ -341,7 +341,7 @@ 341 341 ))) 342 342 343 343 ((( 344 -If the payload=0100003C, it means set the END Node 's TDC to 0x00003C=60(S), while type code is 01.340 +If the payload=0100003C, it means set the END Node’s TDC to 0x00003C=60(S), while type code is 01. 345 345 ))) 346 346 347 347 ((( ... ... @@ -697,8 +697,6 @@ 697 697 * Blink once when device transmit a packet. 698 698 699 699 700 - 701 - 702 702 == 2.9 Installation in Soil == 703 703 704 704 **Measurement the soil surface** ... ... @@ -803,11 +803,11 @@ 803 803 ))) 804 804 805 805 ((( 806 -You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won 't be voltage drop between battery and main board.800 +You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board. 807 807 ))) 808 808 809 809 ((( 810 -The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can 't find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)804 +The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can’t find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes) 811 811 ))) 812 812 813 813 ... ... @@ -1022,15 +1022,15 @@ 1022 1022 1023 1023 = 5. Trouble Shooting = 1024 1024 1025 -== 5.1 Why I can 't join TTN in US915 / AU915 bands? ==1019 +== 5.1 Why I can’t join TTN in US915 / AU915 bands? == 1026 1026 1027 -It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main. End DeviceATCommandsand Downlink Command.WebHome||anchor="H7.19EightChannelMode"]] section above for details.1021 +It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main.LoRaWAN Communication Debug.WebHome||anchor="H2.NoticeofUS9152FCN4702FAU915Frequencyband"]] section above for details. 1028 1028 1029 1029 1030 -== 5.2 AT Command input doesn 't work ==1024 +== 5.2 AT Command input doesn’t work == 1031 1031 1032 1032 ((( 1033 -In the case if user can see the console output but can 't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.1027 +In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string. 1034 1034 ))) 1035 1035 1036 1036 ... ... @@ -1080,8 +1080,6 @@ 1080 1080 (% class="wikigeneratedid" %) 1081 1081 ((( 1082 1082 1083 - 1084 - 1085 1085 ))) 1086 1086 1087 1087 = 7. Packing Info = ... ... @@ -1114,7 +1114,6 @@ 1114 1114 * ((( 1115 1115 Weight / pcs : g 1116 1116 1117 - 1118 1118 1119 1119 ))) 1120 1120