LHT65N-DC Connection Instruction

Connect a Normal Close Door Sensor won't increase sleep current (~~6uA). The power consumption mainly depends on the how many open/close event happen every day.

67

68

69

= 2. Water Sensor =

Application: Connect to Water leakage Sensor detect door open / close and send to IoT server

75

76

77

== 2.1 Hardware Connection ==

78

79

* LHT65N VDD <~-~-> one wire of water leakage Sensor

80

* LHT65N Interrupt Pin <~-~-> one wire of water leakage Sensor

81

82

[[image:image-20240802092327-1.jpeg||height="312" width="694"]]

83

84

== 2.2 Software Configuration ==

85

86

Set LHT65N to Interrupt Mode so device will uplink when there is open/close event

87

88

* AT Command : AT+EXT=4,1

89

* Downlink Command: 0xA20401 : Same as AT+EXT=4,1

90

91

Enlarge the TDC time so LHT65N will send Keep Alive message every 24 hours so to save battery life.

92

93

* AT Command :AT+TDC=86400000

94

* Downlink Command: 01015180 Same as AT+TDC=86400000

95

96

== 2.3 Test Result ==

97

98

99

Partial contact of the sensor probe with water generates open/close events and checks for upstream packets in the platform.

100

101

[[image:image-20240424101908-12.png||height="331" width="435"]]

102

103

[[image:image-20240424101927-13.png||height="303" width="766"]]

104

105

106

== 2.4 Power Consumption Notice ==

107

108

* Connecting the water leak sensor increases the sleep current (~~40uA). When using a water leak sensor, the battery life will be reduced.

109

110

[[image:image-20240424102048-14.png||height="495" width="926"]]

111

112

When the probe comes into contact with water, it will increase the low power consumption by about 300uA.

113

114

Then when it is out of contact with water, the power consumption will slowly drop. The reason for the slow drop is that there are water beads hanging on the surface of the probe. When it dries, It will reduce power consumption.

= 3 Smoke Sensor =

Application: Mainly suitable for hotels, warehouses, guesthouses, restaurants, hostels, factories, oil field well teams, prefabricated houses and other public places.When it is detected that the smoke in the air reaches a certain concentration value, an alarm signal is triggered immediately. False alarms are likely to occur when dew, oil smoke, water vapor, sudden temperature changes, corrosive gases, strong airflow or air conditioning, or outdoor environments occur.

* Technical Notes：

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

125

|=(% style="width: 156px;background-color:#4F81BD;color:white" %)**Parameter name**|=(% style="width: 137px;background-color:#4F81BD;color:white" %)**Explanation**

126

|(% style="width:156px" %)Power|(% style="width:137px" %)DC 3V(Two 1.5V alkaline batteries)

127

|(% style="width:156px" %)Indicator lights|(% style="width:137px" %)It will flash once every minute in the monitoring state, and it will stay on when smoke is detected.

128

|(% style="width:156px" %)Working temperature|(% style="width:137px" %)-10℃~~+50℃

129

|(% style="width:156px" %)Working humidity|(% style="width:137px" %)≤95% (Under 40℃ working environment)

130

131

== 3.1 Hardware Connection ==

132

133

* LHT65N VDD <~-~-> Sound vibration film red line

134

* LHT65N Interrupt Pin <~-~-> sound vibration film black line

135

136

[[image:image-20240428090354-1.jpeg||height="456" width="1015"]]

137

138

139

== 3.2 Software Configuration ==

140

141

142

Set LHT65N to Interrupt Mode so device will uplink when there is open/close event

143

144

* AT Command : AT+EXT=4,1

145

* Downlink Command: 0xA20401 : Same as AT+EXT=4,1

146

147

Enlarge the TDC time so LHT65N will send Keep Alive message every 24 hours so to save battery life.

148

149

* AT Command :AT+TDC=86400000

150

* Downlink Command: 01015180 Same as AT+TDC=86400000

151

152

== 3.3 Test Result ==

153

154

155

[[image:image-20240428090354-2.png||height="771" width="1011"]]

156

157

[[image:image-20240428090354-3.png||height="314" width="1015"]]

158

159

When triggered, the node will send data packets twice. When it is not triggered or the trigger ends, it needs to wait for the TDC time to send data packets.

160

161

162

== 3.4 Power Consumption Notice ==

163

164

When there is smoke detect, the smoke sensor will be trigger , there will be sound from speaker and trigger the LHT65N to send uplink

= 4. SOS switch sensor =

169

170

Application:Connected to the SOS switch, the sensor detects whether an alarm is triggered and sends it to the IoT server.

171

172

When the red button is pressed, 1 and 2 are connected, and 1 and 3 are disconnected. When you release your hand, the red button automatically pops up, 1 and 2 are disconnected, 1 and 3 are connected, and it automatically resets without a key; This emergency help button is used for emergencies or emergencies. Press this red button to give an alarm and SOS emergency call (COM is 1, NO is 2, NC is 3)

173

174

== 4.1 Hardware Connection ==

175

176

177

LHT65N VDD <~-~--> COM port of the SOS button

178

179

LHT65N Interrupt Pin <~-~-> The NO port of the SOS button

180

181

[[image:image-20240429133616-4.jpeg||height="937" width="1065"]]

182

183

184

== 4.2 Software Configuration ==

185

186

187

Set LHT65N to Interrupt Mode so device will uplink when there is open/close event

188

189

* AT Command : AT+EXT=4,1

190

* Downlink Command: 0xA20401 : Same as AT+EXT=4,1

191

192

Enlarge the TDC time so LHT65N will send Keep Alive message every 24 hours so to save battery life.

193

194

* AT Command :AT+TDC=86400000

195

* Downlink Command: 01015180 Same as AT+TDC=86400000

196

197

== 4.3 Test Result ==

198

199

[[image:image-20240429133616-5.jpeg||height="685" width="753"]]

200

201

Note: When the LHT65N triggers an interrupt packet, it needs to wait 6s before a new trigger is generated.

202

203

When the button is pressed, the SOS button will be triggered, and the LHT65N will also be triggered to send the uplink signal.

204

205

206

== 4.4 Power Consumption Notice ==

207

208

Connect SOS button Sensor won't increase sleep current (~~6uA). The power consumption mainly depends on the how many open/close event happen every day.

= 5. Flow sensor =

Application: It detects water flow volume and uplink to IoT server via LoRaWAN network. User can use this to monitor the water usage for buildings.

214

215

== 5.1 Hardware Connection ==

216

217

LHT65N VDD <~-~--> Flow sensor red line

218

219

LHT65N Interrupt Pin <~-~-> Flow sensor Signal line

220

221

LHT65N GND <~-~--> Flow sensor black line(Note: If the sensor does not need power supply, please connect the red line (rising edge trigger) or the black line (falling edge trigger) as needed.)

222

223

[[image:image-20240506111329-1.jpeg||height="654" width="388"]]

224

225

226

== 5.2 Software Configuration ==

227

228

Note: Because the traffic sensor is a counting sensor, the node can only be set in counting mode.

229

230

Set LHT65N to Counting Mode so device will uplink when there is open/close event

231

232

* AT Command : AT+EXT=8,1

233

* Downlink Command: 0xA2080101 : Same as AT+EXT=8,1

234

235

Enlarge the TDC time so LHT65N will send Keep Alive message every 24 hours so to save battery life.

236

237

* AT Command :AT+TDC=86400000

238

* Downlink Command: 01015180 Same as AT+TDC=86400000

239

240

== 5.3 Test Result ==

241

242

[[image:image-20240506111329-2.jpeg||height="533" width="336"]]

243

244

When the water passes through the flow sensor, the cumulative count will be generated (note: when installing the flow sensor, it is necessary to pay attention to the inlet direction of the installation).

245

246

[[image:image-20240506111329-3.png||height="377" width="1134"]]

247

248

249

== 5.4 Power Consnmption Notice ==

250

251

Connect Flow Sensor won't increase sleep current (~~6uA). The power consumption mainly depends on the how many counting event happen every day.

252

253

Wiki source code of LHT65N-DC Connection Instruction

Applications

Navigation