Changes for page LDDS45 - LoRaWAN Distance Detection Sensor User Manual
Last modified by Mengting Qiu on 2025/02/26 15:04
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -62,6 +62,11 @@ 62 62 * [[10. Support>>path:#H10.A0200BSupport]] 63 63 64 64 65 + 66 + 67 + 68 + 69 + 65 65 = 1. Introduction = 66 66 67 67 == 1.1 What is LoRaWAN Soil pH Sensor == ... ... @@ -107,6 +107,7 @@ 107 107 * IP68 rate for the Sensor Probe 108 108 * 8500mAh Battery for long term use 109 109 115 + 110 110 == 1.3 Probe Specification == 111 111 112 112 ... ... @@ -128,15 +128,11 @@ 128 128 * Length: 3.5 meters 129 129 130 130 131 - 132 - 133 133 == 1.4 Applications == 134 134 135 135 * Smart Agriculture 136 136 137 137 138 - 139 - 140 140 == 1.5 Pin mapping and power on == 141 141 142 142 [[image:1654592472094-134.png]] ... ... @@ -336,7 +336,6 @@ 336 336 337 337 338 338 339 - 340 340 === 2.3.7 Decode payload in The Things Network === 341 341 342 342 While using TTN network, you can add the payload format to decode the payload. ... ... @@ -549,7 +549,6 @@ 549 549 550 550 551 551 552 - 553 553 == 2.8 Frequency Plans == 554 554 555 555 ((( ... ... @@ -747,8 +747,6 @@ 747 747 * Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include) 748 748 749 749 750 - 751 - 752 752 === 2.8.5 AS920-923 & AS923-925 (AS923) === 753 753 754 754 ((( ... ... @@ -859,109 +859,56 @@ 859 859 860 860 === 2.8.6 KR920-923 (KR920) === 861 861 862 -((( 863 863 (% style="color:blue" %)**Default channel:** 864 -))) 865 865 866 -((( 867 867 922.1 - SF7BW125 to SF12BW125 868 -))) 869 869 870 -((( 871 871 922.3 - SF7BW125 to SF12BW125 872 -))) 873 873 874 -((( 875 875 922.5 - SF7BW125 to SF12BW125 876 -))) 877 877 878 -((( 879 - 880 -))) 881 881 882 -((( 883 883 (% style="color:blue" %)**Uplink: (OTAA mode, channel added by JoinAccept message)** 884 -))) 885 885 886 -((( 887 887 922.1 - SF7BW125 to SF12BW125 888 -))) 889 889 890 -((( 891 891 922.3 - SF7BW125 to SF12BW125 892 -))) 893 893 894 -((( 895 895 922.5 - SF7BW125 to SF12BW125 896 -))) 897 897 898 -((( 899 899 922.7 - SF7BW125 to SF12BW125 900 -))) 901 901 902 -((( 903 903 922.9 - SF7BW125 to SF12BW125 904 -))) 905 905 906 -((( 907 907 923.1 - SF7BW125 to SF12BW125 908 -))) 909 909 910 -((( 911 911 923.3 - SF7BW125 to SF12BW125 912 -))) 913 913 914 -((( 915 - 916 -))) 917 917 918 -((( 919 919 (% style="color:blue" %)**Downlink:** 920 -))) 921 921 922 -((( 923 923 Uplink channels 1-7(RX1) 924 -))) 925 925 926 -((( 927 927 921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125) 928 -))) 929 929 930 930 931 931 932 932 === 2.8.7 IN865-867 (IN865) === 933 933 934 -((( 935 935 (% style="color:blue" %)**Uplink:** 936 -))) 937 937 938 -((( 939 939 865.0625 - SF7BW125 to SF12BW125 940 -))) 941 941 942 -((( 943 943 865.4025 - SF7BW125 to SF12BW125 944 -))) 945 945 946 -((( 947 947 865.9850 - SF7BW125 to SF12BW125 948 -))) 949 949 950 -((( 951 - 952 -))) 953 953 954 -((( 955 955 (% style="color:blue" %)**Downlink:** 956 -))) 957 957 958 -((( 959 959 Uplink channels 1-3 (RX1) 960 -))) 961 961 962 -((( 963 963 866.550 - SF10BW125 (RX2) 964 -))) 965 965 966 966 967 967 ... ... @@ -973,7 +973,6 @@ 973 973 * Blink once when device transmit a packet. 974 974 975 975 976 - 977 977 == 2.10 Firmware Change Log == 978 978 979 979 ... ... @@ -988,51 +988,26 @@ 988 988 989 989 = 3. Configure LSPH01 via AT Command or LoRaWAN Downlink = 990 990 991 -((( 992 992 Use can configure LSPH01 via AT Command or LoRaWAN Downlink. 993 -))) 994 994 995 -* ((( 996 -AT Command Connection: See [[FAQ>>path:#H6.FAQ]]. 997 -))) 998 -* ((( 999 -LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>path:/xwiki/bin/view/Main/]] 1000 -))) 937 +* AT Command Connection: See [[FAQ>>path:#H6.FAQ]]. 938 +* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>path:/xwiki/bin/view/Main/]] 1001 1001 1002 -((( 1003 1003 There are two kinds of commands to configure LSPH01, they are: 1004 -))) 1005 1005 1006 -* ((( 1007 -(% style="color:#4f81bd" %)** General Commands**. 1008 -))) 942 +* (% style="color:#4f81bd" %)** General Commands**. 1009 1009 1010 -((( 1011 1011 These commands are to configure: 1012 -))) 1013 1013 1014 -* ((( 1015 -General system settings like: uplink interval. 1016 -))) 1017 -* ((( 1018 -LoRaWAN protocol & radio related command. 1019 -))) 946 +* General system settings like: uplink interval. 947 +* LoRaWAN protocol & radio related command. 1020 1020 1021 -((( 1022 1022 They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:[[End Device AT Commands and Downlink Command>>path:/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]] 1023 -))) 1024 1024 1025 -((( 1026 - 1027 -))) 1028 1028 1029 -* ((( 1030 -(% style="color:#4f81bd" %)** Commands special design for LSPH01** 1031 -))) 952 +* (% style="color:#4f81bd" %)** Commands special design for LSPH01** 1032 1032 1033 -((( 1034 1034 These commands only valid for LSPH01, as below: 1035 -))) 1036 1036 1037 1037 1038 1038 ... ... @@ -1046,27 +1046,16 @@ 1046 1046 1047 1047 1048 1048 1049 -((( 1050 1050 (% style="color:#037691" %)**Downlink Command: 0x01** 1051 -))) 1052 1052 1053 -((( 1054 1054 Format: Command Code (0x01) followed by 3 bytes time value. 1055 -))) 1056 1056 1057 -((( 1058 1058 If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01. 1059 -))) 1060 1060 1061 -* ((( 1062 -Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds 1063 -))) 1064 -* ((( 1065 -Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds 974 +* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds 975 +* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds 1066 1066 1067 1067 1068 - 1069 -))) 1070 1070 1071 1071 == 3.2 Set Interrupt Mode == 1072 1072 ... ... @@ -1077,31 +1077,15 @@ 1077 1077 [[image:image-20220607171716-9.png]] 1078 1078 1079 1079 1080 -((( 1081 1081 (% style="color:#037691" %)**Downlink Command: 0x06** 1082 -))) 1083 1083 1084 -((( 1085 1085 Format: Command Code (0x06) followed by 3 bytes. 1086 -))) 1087 1087 1088 -((( 1089 1089 This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06. 1090 -))) 1091 1091 1092 -* ((( 1093 -Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode 1094 -))) 1095 -* ((( 1096 -Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger 1097 -))) 994 +* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode 995 +* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger 1098 1098 1099 -((( 1100 - 1101 -))) 1102 - 1103 - 1104 - 1105 1105 == 3.3 Calibrate Sensor == 1106 1106 1107 1107 Detail See [[Calibration Guide>>path:#H2.7Calibration]] for the user of 0x13 and 0x14 downlink commands ... ... @@ -1276,13 +1276,9 @@ 1276 1276 1277 1277 === 4.3.2 Replace the battery === 1278 1278 1279 -((( 1280 1280 You can change the battery in the LSPH01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board. 1281 -))) 1282 1282 1283 -((( 1284 1284 The default battery pack of LSPH01 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes) 1285 -))) 1286 1286 1287 1287 1288 1288 ... ... @@ -1303,9 +1303,7 @@ 1303 1303 (% style="background-color:yellow" %)** USB TTL RXD <~-~-~-~-> UART_TXD** 1304 1304 1305 1305 1306 -((( 1307 1307 In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LSPH01. LSPH01 will output system info once power on as below: 1308 -))) 1309 1309 1310 1310 1311 1311 [[image:1654593712276-618.png]]