Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -55,8 +55,6 @@
55	55	* IP68 rate for the Sensor Probe
56	56	* 8500mAh Battery for long term use
57	57
58		-
59		-
60	60	== 1.3 Probe Specification ==
61	61
62	62
...	...	@@ -77,12 +77,10 @@
77	77	* IP68 Protection
78	78	* Length: 3.5 meters
79	79
80		-
81	81	== 1.4 ​Applications ==
82	82
83	83	* Smart Agriculture
84	84
85		-
86	86	== 1.5 Pin mapping and power on ==
87	87
88	88	[[image:1654580482666-473.png]]
...	...	@@ -269,8 +269,6 @@
269	269	|0x02|Reply configures info|[[Configure Info Payload>>||anchor="H3.4GetFirmwareVersionInfo"]]
270	270	|0x03|Reply Calibration Info|[[Calibration Payload>>||anchor="H2.7Calibration"]]
271	271
272		-
273		-
274	274	=== 2.3.7 Decode payload in The Things Network ===
275	275
276	276	While using TTN network, you can add the payload format to decode the payload.
...	...	@@ -440,8 +440,6 @@
440	440	* Reply to the confirmation package: 14 01
441	441	* Reply to non-confirmed packet: 14 00
442	442
443		-
444		-
445	445	== 2.8 Frequency Plans ==
446	446
447	447	(((
...	...	@@ -676,8 +676,6 @@
676	676	* The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
677	677	* Blink once when device transmit a packet.
678	678
679		-
680		-
681	681	== 2.10 ​Firmware Change Log ==
682	682
683	683
...	...	@@ -746,6 +746,7 @@
746	746	* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
747	747	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
748	748
	739	+
749	749	== 3.2 Set Interrupt Mode ==
750	750
751	751	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -764,9 +764,10 @@
764	764	* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
765	765	* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
766	766
	758	+
767	767	== 3.3 Calibrate Sensor ==
768	768
769		-Detail See [[Calibration Guide>>||anchor="2.7Calibration"]] for the user of 0x13 and 0x14 downlink commands
	761	+Detail See [[Calibration Guide>>||anchor="H2.7Calibration"]] for the user of 0x13 and 0x14 downlink commands
770	770
771	771
772	772
...	...	@@ -781,7 +781,6 @@
781	781	* Reply to the confirmation package: 26 01
782	782	* Reply to non-confirmed packet: 26 00
783	783
784		-
785	785	Device will send an uplink after got this downlink command. With below payload:
786	786
787	787	Configures info payload:
...	...	@@ -967,7 +967,7 @@
967	967
968	968	[[image:1654589062541-567.png]]
969	969
970		-Valid AT Command please check [[Configure Device>>path:#Configure_Device]].
	961	+Valid AT Command please check [[Configure Device>>||anchor="H3.ConfigureLSPH01viaATCommandorLoRaWANDownlink"]].
971	971
972	972
973	973
...	...	@@ -1004,6 +1004,7 @@
1004	1004	* (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
1005	1005	* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
1006	1006
	998	+
1007	1007	= 9. ​Packing Info =
1008	1008
1009	1009