Last modified by Mengting Qiu on 2025/02/26 15:04
<
From version < 26.9 >
edited by Xiaoling
on 2022/06/07 15:11
To version < 34.2 >
edited by Xiaoling
on 2022/06/07 16:05
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -427,8 +427,6 @@
427 427  Always 0x03
428 428  )))
429 429  
430 -
431 -
432 432  User can also send 0x14 downlink command to poll the current calibration payload.
433 433  
434 434  [[image:image-20220607145603-4.png]]
... ... @@ -436,6 +436,8 @@
436 436  * Reply to the confirmation package: 14 01
437 437  * Reply to non-confirmed packet: 14 00
438 438  
437 +
438 +
439 439  == 2.8 Frequency Plans ==
440 440  
441 441  (((
... ... @@ -557,6 +557,7 @@
557 557  * Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
558 558  * Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
559 559  
560 +
560 560  === 2.8.5 AS920-923 & AS923-925 (AS923) ===
561 561  
562 562  (% style="color:blue" %)**Default Uplink channel:**
... ... @@ -670,35 +670,29 @@
670 670  * The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
671 671  * Blink once when device transmit a packet.
672 672  
674 +
673 673  == 2.10 ​Firmware Change Log ==
674 674  
677 +
675 675  **Firmware download link:**
676 676  
677 677  [[http:~~/~~/www.dragino.com/downloads/index.pHp?dir=LoRa_End_Node/LSPH01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
678 678  
679 679  
680 -**Firmware Upgrade Method:[[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]**
683 +**Firmware Upgrade Method: **[[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]
681 681  
682 -[[http:~~/~~/wiki.dragino.com/index.pHp?title=Firmware_Upgrade_Instruction_for_STM32_base_products#Introduction>>url:http://wiki.dragino.com/index.php?title=Firmware_Upgrade_Instruction_for_STM32_base_products#Introduction]]
683 683  
684 684  
687 += 3. Configure LSPH01 via AT Command or LoRaWAN Downlink =
685 685  
686 -
687 -
688 -
689 -1. Configure LSPH01 via AT Command or LoRaWAN Downlink
690 -
691 691  Use can configure LSPH01 via AT Command or LoRaWAN Downlink.
692 692  
693 -* AT Command Connection: See [[FAQ>>path:#AT_COMMAND]].
694 -* LoRaWAN Downlink instruction for different platforms:
691 +* AT Command Connection: See [[FAQ>>||anchor="H6.FAQ"]].
692 +* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]]
695 695  
696 -[[http:~~/~~/wiki.dragino.com/index.pHp?title=Main_Page#Use_Note_for_Server>>url:http://wiki.dragino.com/index.php?title=Main_Page#Use_Note_for_Server]]
697 -
698 -
699 699  There are two kinds of commands to configure LSPH01, they are:
700 700  
701 -* **General Commands**.
696 +* (% style="color:#4f81bd" %)** General Commands**.
702 702  
703 703  These commands are to configure:
704 704  
... ... @@ -705,25 +705,25 @@
705 705  * General system settings like: uplink interval.
706 706  * LoRaWAN protocol & radio related command.
707 707  
708 -They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
703 +They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:[[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
709 709  
710 -[[http:~~/~~/wiki.dragino.com/index.pHp?title=End_Device_Downlink_Command>>url:http://wiki.dragino.com/index.php?title=End_Device_Downlink_Command]]
711 711  
706 +* (% style="color:#4f81bd" %)** Commands special design for LSPH01**
712 712  
713 -* **Commands special design for LSPH01**
714 -
715 715  These commands only valid for LSPH01, as below:
716 716  
717 717  
718 -1.
719 -11. Set Transmit Interval Time
720 720  
712 +== 3.1 Set Transmit Interval Time ==
713 +
721 721  Feature: Change LoRaWAN End Node Transmit Interval.
722 722  
723 -**AT Command: AT+TDC**
716 +(% style="color:#037691" %)**AT Command: AT+TDC**
724 724  
725 -|**Command Example**|**Function**|**Response**
726 -|AT+TDC=?|Show current transmit Interval|(((
718 +
719 +(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:710px" %)
720 +|(% style="width:154px" %)**Command Example**|(% style="width:223px" %)**Function**|(% style="width:330px" %)**Response**
721 +|(% style="width:154px" %)AT+TDC=?|(% style="width:223px" %)Show current transmit Interval|(% style="width:330px" %)(((
727 727  30000
728 728  
729 729  OK
... ... @@ -730,13 +730,13 @@
730 730  
731 731  the interval is 30000ms = 30s
732 732  )))
733 -|AT+TDC=60000|Set Transmit Interval|(((
728 +|(% style="width:154px" %)AT+TDC=60000|(% style="width:223px" %)Set Transmit Interval|(% style="width:330px" %)(((
734 734  OK
735 735  
736 736  Set transmit interval to 60000ms = 60 seconds
737 737  )))
738 738  
739 -**Downlink Command: 0x01**
734 +(% style="color:#037691" %)**Downlink Command: 0x01**
740 740  
741 741  Format: Command Code (0x01) followed by 3 bytes time value.
742 742  
... ... @@ -745,32 +745,17 @@
745 745  * Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
746 746  * Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
747 747  
748 -1.
749 -11. Set Interrupt Mode
743 +== 3.2 Set Interrupt Mode ==
750 750  
751 751  Feature, Set Interrupt mode for GPIO_EXIT.
752 752  
753 -**AT Command: AT+INTMOD**
747 +(% style="color:#037691" %)**AT Command: AT+INTMOD**
754 754  
755 -|**Command Example**|**Function**|**Response**
756 -|AT+INTMOD=?|Show current interrupt mode|(((
757 -0
749 +[[image:image-20220607153759-6.png]]
758 758  
759 -OK
760 760  
761 -the mode is 0 = No interruption
762 -)))
763 -|AT+INTMOD=2|(((
764 -Set Transmit Interval
752 +(% style="color:#037691" %)**Downlink Command: 0x06**
765 765  
766 -1. (Disable Interrupt),
767 -1. (Trigger by rising and falling edge),
768 -1. (Trigger by falling edge)
769 -1. (Trigger by rising edge)
770 -)))|OK
771 -
772 -**Downlink Command: 0x06**
773 -
774 774  Format: Command Code (0x06) followed by 3 bytes.
775 775  
776 776  This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
... ... @@ -778,25 +778,20 @@
778 778  * Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
779 779  * Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
780 780  
781 -1.
782 -11. Calibrate Sensor
761 +== 3.3 Calibrate Sensor ==
783 783  
784 -Detail See [[Calibration Guide>>path:#Calibration]] for the user of 0x13 and 0x14 downlink commands
763 +Detail See [[Calibration Guide>>||anchor="2.7Calibration"]] for the user of 0x13 and 0x14 downlink commands
785 785  
786 786  
787 787  
788 -1.
789 -11. Get Firmware Version Info
767 +== 3.4 Get Firmware Version Info ==
790 790  
791 791  Feature: use downlink to get firmware version.
792 792  
771 +(% style="color:#037691" %)**Downlink Command: 0x26**
793 793  
794 -**Downlink Command: 0x26**
773 +[[image:image-20220607154718-7.png]]
795 795  
796 -
797 -|**Downlink Control Type**|**FPort**|**Type Code**|**Downlink payload size(bytes)**
798 -|Get Firmware Version Info|Any|26|2
799 -
800 800  * Reply to the confirmation package: 26 01
801 801  * Reply to non-confirmed packet: 26 00
802 802  
... ... @@ -804,11 +804,10 @@
804 804  
805 805  Configures info payload:
806 806  
807 -|(((
808 -**Size**
809 -
810 -**(bytes)**
811 -)))|**1**|**1**|**1**|**1**|**1**|**5**|**1**
782 +(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
783 +|=(((
784 +**Size(bytes)**
785 +)))|=**1**|=**1**|=**1**|=**1**|=**1**|=**5**|=**1**
812 812  |**Value**|Software Type|(((
813 813  Frequency
814 814  
... ... @@ -818,10 +818,7 @@
818 818  
819 819  Version
820 820  )))|Sensor Type|Reserve|(((
821 -[[Message>>path:#Message_Type]]
822 -
823 -[[Type>>path:#Message_Type]]
824 -
795 +[[Message Type>>||anchor="H2.3.6MessageType"]]
825 825  Always 0x02
826 826  )))
827 827  
... ... @@ -875,18 +875,19 @@
875 875  
876 876  
877 877  
849 += 4. Battery & How to replace =
878 878  
851 +== 4.1 Battery Type ==
879 879  
880 -
881 -1. Battery & How to replace
882 -11. Battery Type
883 -
853 +(((
884 884  LSPH01 is equipped with a [[8500mAH ER26500 Li-SOCI2 battery>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]. The battery is un-rechargeable battery with low discharge rate targeting for 8~~10 years use. This type of battery is commonly used in IoT target for long-term running, such as water meter.
855 +)))
885 885  
886 -
857 +(((
887 887  The discharge curve is not linear so can’t simply use percentage to show the battery level. Below is the battery performance.
859 +)))
888 888  
889 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]]
861 +[[image:1654588469844-778.png]]
890 890  
891 891  
892 892  Minimum Working Voltage for the LSPH01:
... ... @@ -894,30 +894,36 @@
894 894  LSPH01:  2.45v ~~ 3.6v
895 895  
896 896  
897 -1.
898 -11. Replace Battery
899 899  
870 +== 4.2 Replace Battery ==
871 +
872 +(((
900 900  Any battery with range 2.45 ~~ 3.6v can be a replacement. We recommend to use Li-SOCl2 Battery.
874 +)))
901 901  
876 +(((
902 902  And make sure the positive and negative pins match.
878 +)))
903 903  
904 904  
905 905  
906 -1.
907 -11. Power Consumption Analyze
882 +== 4.3 Power Consumption Analyze ==
908 908  
884 +(((
909 909  Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
886 +)))
910 910  
911 -
888 +(((
912 912  Instruction to use as below:
890 +)))
913 913  
914 914  
915 -Step 1: Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from:
893 +**Step 1**: Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from:
916 916  
917 917  [[https:~~/~~/www.dragino.com/downloads/index.pHp?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
918 918  
919 919  
920 -Step 2: Open it and choose
898 +**Step 2**: Open it and choose
921 921  
922 922  * Product Model
923 923  * Uplink Interval
... ... @@ -925,64 +925,62 @@
925 925  
926 926  And the Life expectation in difference case will be shown on the right.
927 927  
928 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]
906 +[[image:1654588577573-122.png]]
929 929  
930 930  
931 931  The battery related documents as below:
932 932  
933 -* [[Battery Dimension>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]],
934 -* [[Lithium-Thionyl Chloride Battery>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]] datasheet
935 -* [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
936 -
937 -|(((
938 -JST-XH-2P connector
911 +* (((
912 +[[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
939 939  )))
914 +* (((
915 +[[Lithium-Thionyl Chloride Battery  datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
916 +)))
917 +* (((
918 +[[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
919 +)))
940 940  
941 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png]]
921 +[[image:image-20220607155856-8.png]]
942 942  
943 943  
944 944  
945 -1.
946 -11.
947 -111. ​Battery Note
925 +=== 4.3.1 ​Battery Note ===
948 948  
927 +(((
949 949  The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
929 +)))
950 950  
951 951  
952 -1.
953 -11.
954 -111. ​Replace the battery
955 955  
933 +=== ​4.3.2 Replace the battery ===
934 +
956 956  You can change the battery in the LSPH01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
957 957  
958 -
959 959  The default battery pack of LSPH01 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
960 960  
961 961  
962 962  
941 += 5. Use AT Command =
963 963  
943 +== 5.1 Access AT Commands ==
964 964  
965 -
966 -1. Use AT Command
967 -11. Access AT Commands
968 -
969 969  LSPH01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSPH01 for using AT command, as below.
970 970  
971 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.png]]
947 +[[image:1654589001411-343.png]]
972 972  
973 973  Connection:
974 974  
975 -USB TTL GND <~-~-~-~-> GND
951 +(% style="background-color:yellow" %)** USB TTL GND <~-~-~-~-> GND**
976 976  
977 -USB TTL TXD <~-~-~-~-> UART_RXD
953 +(% style="background-color:yellow" %)** USB TTL TXD  <~-~-~-~-> UART_RXD**
978 978  
979 -USB TTL RXD <~-~-~-~-> UART_TXD
955 +(% style="background-color:yellow" %)** USB TTL RXD  <~-~-~-~-> UART_TXD**
980 980  
981 981  
982 982  In the PC, you need to set the serial baud rate to **9600** to access the serial console for LSPH01. LSPH01 will output system info once power on as below:
983 983  
984 984  
985 - [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]]
961 + [[image:1654589062541-567.png]]
986 986  
987 987  Valid AT Command please check [[Configure Device>>path:#Configure_Device]].
988 988  
1654588469844-778.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +75.8 KB
Content
1654588577573-122.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +138.2 KB
Content
1654589001411-343.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +546.2 KB
Content
1654589062541-567.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +144.0 KB
Content
image-20220607153237-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +12.9 KB
Content
image-20220607153759-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +17.2 KB
Content
image-20220607154718-7.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +6.0 KB
Content
image-20220607155856-8.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +83.5 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0