Changes for page LDDS45 - LoRaWAN Distance Detection Sensor User Manual

Last modified by Mengting Qiu on 2025/02/26 15:04

From version < 149.10 >

edited by Xiaoling
on 2022/06/10 18:13

To version < 147.2 >

edited by Xiaoling
on 2022/06/10 17:34

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Attachments (0 modified, 0 added, 2 removed)
- image-20220610174836-8.png
- image-20220610174917-9.png

Details

Page properties

Content

@@ -57,6 +57,7 @@
  * IP66 Waterproof Enclosure
  * 4000mAh or 8500mAh Battery for long term use
++
  == 1.3  Specification ==
  === 1.3.1  Rated environmental conditions ===
@@ -97,6 +97,7 @@
  * Sewer
  * Bottom water level monitoring
++
  == 1.6  Pin mapping and power on ==
@@ -237,6 +237,7 @@
  * If the sensor value is 0x0000, it means system doesn’t detect ultrasonic sensor.
  * If the sensor value lower than 0x0118 (280mm), the sensor value will be invalid. Since v1.1.4, all value lower than 280mm will be set to 0x0014(20mm) which means the value is invalid.
++
  === 2.3.3  Interrupt Pin ===
  This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H4.2A0SetInterruptMode"]] for the hardware and software set up.
@@ -806,6 +806,7 @@
  * Solid ON for 5 seconds once device successful Join the network.
  * Blink once when device transmit a packet.
++
  == 2.8  Firmware Change Log ==
@@ -824,7 +824,7 @@
  [[image:image-20220610172003-2.png]]
--== 2.10  Battery Analysis ==
++== 2.10  Battery Analysis  ==
  === 2.10.1  Battery Type ===
@@ -970,88 +970,287 @@
  [[image:image-20220610173409-7.png]]
++
++
  (((
--(% style="color:#037691" %)**Downlink Command: 0x01**
++(% style="color:#037691" %)**Downlink Command: 0x06**
  )))
  (((
++Format: Command Code (0x06) followed by 3 bytes.
++)))
++
  (((
--Format: Command Code (0x01) followed by 3 bytes time value.
++This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
++)))
--If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
++* (((
++Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
++)))
++* (((
++Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
++)))
--* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
--* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
++== 3.3  Get Firmware Version Info ==
++
++Feature: use downlink to get firmware version.
++
++(% style="color:#037691" %)**Downlink Command: 0x26**
++
++[[image:image-20220607171917-10.png]]
++
++* Reply to the confirmation package: 26 01
++* Reply to non-confirmed packet: 26 00
++
++Device will send an uplink after got this downlink command. With below payload:
++
++Configures info payload:
++
++(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
++|=(((
++**Size(bytes)**
++)))|=**1**|=**1**|=**1**|=**1**|=**1**|=**5**|=**1**
++|**Value**|Software Type|(((
++Frequency
++
++Band
++)))|Sub-band|(((
++Firmware
++
++Version
++)))|Sensor Type|Reserve|(((
++[[Message Type>>||anchor="H2.3.7A0MessageType"]]
++Always 0x02
  )))
++**Software Type**: Always 0x03 for LLDS12
--
++
++**Frequency Band**:
++
++*0x01: EU868
++
++*0x02: US915
++
++*0x03: IN865
++
++*0x04: AU915
++
++*0x05: KZ865
++
++*0x06: RU864
++
++*0x07: AS923
++
++*0x08: AS923-1
++
++*0x09: AS923-2
++
++*0xa0: AS923-3
++
++
++**Sub-Band**: value 0x00 ~~ 0x08
++
++
++**Firmware Version**: 0x0100, Means: v1.0.0 version
++
++
++**Sensor Type**:
++
++0x01: LSE01
++
++0x02: LDDS75
++
++0x03: LDDS20
++
++0x04: LLMS01
++
++0x05: LSPH01
++
++0x06: LSNPK01
++
++0x07: LLDS12
++
++
++
++= 5.  Battery & How to replace =
++
++== 5.1  Battery Type ==
++
++(((
++LLDS12 is equipped with a [[8500mAH ER26500 Li-SOCI2 battery>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]. The battery is un-rechargeable battery with low discharge rate targeting for 8~~10 years use. This type of battery is commonly used in IoT target for long-term running, such as water meter.
  )))
--== 3.3  Set Interrupt Mode ==
++(((
++The discharge curve is not linear so can’t simply use percentage to show the battery level. Below is the battery performance.
++)))
--Feature, Set Interrupt mode for GPIO_EXIT.
++[[image:1654593587246-335.png]]
--(% style="color:#037691" %)**Downlink Command: AT+INTMOD**
--[[image:image-20220610174917-9.png]]
++Minimum Working Voltage for the LLDS12:
++LLDS12:  2.45v ~~ 3.6v
--(% style="color:#037691" %)**Downlink Command: 0x06**
--Format: Command Code (0x06) followed by 3 bytes.
--This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
++== 5.2  Replace Battery ==
--* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
--* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
++(((
++Any battery with range 2.45 ~~ 3.6v can be a replacement. We recommend to use Li-SOCl2 Battery.
++)))
++(((
++And make sure the positive and negative pins match.
++)))
--= 4.  FAQ =
++== 5.3  Power Consumption Analyze ==
--== 4.1  What is the frequency plan for LDDS75? ==
++(((
++Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
++)))
--LDDS75 use the same frequency as other Dragino products. User can see the detail from this link:  [[Introduction>>doc:Main.End Device Frequency Band.WebHome||anchor="H1.Introduction"]]
++(((
++Instruction to use as below:
++)))
++**Step 1**: Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from:
--== 4.2  How to change the LoRa Frequency Bands/Region ==
++[[https:~~/~~/www.dragino.com/downloads/index.pHp?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
--You can follow the instructions for [[how to upgrade image>>||anchor="H2.8A0200BFirmwareChangeLog"]].
--When downloading the images, choose the required image file for download.
++**Step 2**: Open it and choose
++* Product Model
++* Uplink Interval
++* Working Mode
--== 4.3  Can I use LDDS75 in condensation environment? ==
++And the Life expectation in difference case will be shown on the right.
--LDDS75 is not suitable to be used in condensation environment. Condensation on the LDDS75 probe will affect the reading and always got 0.
++[[image:1654593605679-189.png]]
++The battery related documents as below:
--= 5.  Trouble Shooting =
++* (((
++[[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
++)))
++* (((
++[[Lithium-Thionyl Chloride Battery  datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
++)))
++* (((
++[[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
++)))
--== 5.1  Why I can’t join TTN V3 in US915 / AU915 bands? ==
++[[image:image-20220607172042-11.png]]
--It is due to channel mapping. Please see below link:  [[Frequency band>>doc:Main.LoRaWAN Communication Debug.WebHome||anchor="H2.NoticeofUS9152FCN4702FAU915Frequencyband"]]
--== 5.2  AT Command input doesn't work ==
++=== 5.3.1  Battery Note ===
++(((
++The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
++)))
++
++
++
++=== 5.3.2  Replace the battery ===
++
++(((
++You can change the battery in the LLDS12.The type of battery is not limited as long as the output is between 3v to 3.6v.  On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
++)))
++
++(((
++The default battery pack of LLDS12 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
++)))
++
++
++
++= 6.  Use AT Command =
++
++== 6.1  Access AT Commands ==
++
++LLDS12 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LLDS12 for using AT command, as below.
++
++[[image:1654593668970-604.png]]
++
++**Connection:**
++
++(% style="background-color:yellow" %)** USB TTL GND <~-~-~-~-> GND**
++
++(% style="background-color:yellow" %)** USB TTL TXD  <~-~-~-~-> UART_RXD**
++
++(% style="background-color:yellow" %)** USB TTL RXD  <~-~-~-~-> UART_TXD**
++
++
++(((
++(((
++In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LLDS12.
++)))
++
++(((
++LLDS12 will output system info once power on as below:
++)))
++)))
++
++
++ [[image:1654593712276-618.png]]
++
++Valid AT Command please check [[Configure Device>>||anchor="H4.A0ConfigureLLDS12viaATCommandorLoRaWANDownlink"]].
++
++
++= 7.  FAQ =
++
++== 7.1  How to change the LoRa Frequency Bands/Region ==
++
++You can follow the instructions for [[how to upgrade image>>||anchor="H2.8A0200BFirmwareChangeLog"]].
++When downloading the images, choose the required image file for download.
++
++
++= 8.  Trouble Shooting =
++
++== 8.1  AT Commands input doesn’t work ==
++
++
++(((
  In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
++)))
++
++== 8.2  Significant error between the output distant value of LiDAR and actual distance ==
++
++
  (((
++(% style="color:blue" %)**Cause ①**(%%)**：**Due to the physical principles of The LiDAR probe, the above phenomenon is likely to occur if the detection object is the material with high reflectivity (such as mirror, smooth floor tile, etc.) or transparent substance (such as glass and water, etc.)
++)))
++
++(((
++Troubleshooting: Please avoid use of this product under such circumstance in practice.
++)))
++
++(((
  )))
++(((
++(% style="color:blue" %)**Cause ②**(%%)**: **The IR-pass filters are blocked.
++)))
--= 6.  Order Info =
++(((
++Troubleshooting: please use dry dust-free cloth to gently remove the foreign matter.
++)))
--Part Number: (% style="color:blue" %)**LDDS75-XX-YY**
++= 9.  Order Info =
++
++Part Number: (% style="color:blue" %)**LLDS12-XX**
++
++
  (% style="color:blue" %)**XX**(%%): The default frequency band
  * (% style="color:red" %)**AS923**(%%):  LoRaWAN AS923 band
@@ -1063,17 +1063,12 @@
  * (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
--(% style="color:blue" %)**YY**(%%): Battery Option
++= 10.  Packing Info =
--* (% style="color:red" %)**4**(%%): 4000mAh battery
--* (% style="color:red" %)**8**(%%): 8500mAh battery
--= 7.  Packing Info =
--
--
  **Package Includes**:
--* LDDS75 LoRaWAN Distance Detection Sensor x 1
++* LLDS12 LoRaWAN LiDAR Distance Sensor x 1
  **Dimension and weight**:
@@ -1082,7 +1082,7 @@
  * Package Size / pcs : cm
  * Weight / pcs : g
--= 8.  Support =
++= 11.  Support =
  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]].

image-20220610174836-8.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-34.3 KB

Content

image-20220610174917-9.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-34.3 KB

Content

Changes for page LDDS45 - LoRaWAN Distance Detection Sensor User Manual

Summary

Details

Applications

Navigation