Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -57,6 +57,7 @@
57	57	* IP66 Waterproof Enclosure
58	58	* 4000mAh or 8500mAh Battery for long term use
59	59
	60	+
60	60	== 1.3  Specification ==
61	61
62	62	=== 1.3.1  Rated environmental conditions ===
...	...	@@ -97,6 +97,7 @@
97	97	* Sewer
98	98	* Bottom water level monitoring
99	99
	101	+
100	100	== 1.6  Pin mapping and power on ==
101	101
102	102
...	...	@@ -237,6 +237,7 @@
237	237	* If the sensor value is 0x0000, it means system doesn’t detect ultrasonic sensor.
238	238	* If the sensor value lower than 0x0118 (280mm), the sensor value will be invalid. Since v1.1.4, all value lower than 280mm will be set to 0x0014(20mm) which means the value is invalid.
239	239
	242	+
240	240	=== 2.3.3  Interrupt Pin ===
241	241
242	242	This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H4.2A0SetInterruptMode"]] for the hardware and software set up.
...	...	@@ -806,6 +806,7 @@
806	806	* Solid ON for 5 seconds once device successful Join the network.
807	807	* Blink once when device transmit a packet.
808	808
	812	+
809	809	== 2.8  ​Firmware Change Log ==
810	810
811	811
...	...	@@ -824,7 +824,7 @@
824	824	[[image:image-20220610172003-2.png]]
825	825
826	826
827		-== 2.10  Battery Analysis ==
	831	+== 2.10  Battery Analysis ==
828	828
829	829	=== 2.10.1  Battery Type ===
830	830
...	...	@@ -970,6 +970,8 @@
970	970	[[image:image-20220610173409-7.png]]
971	971
972	972
	977	+
	978	+
973	973	(((
974	974	(% style="color:#037691" %)**Downlink Command: 0x01**
975	975	)))
...	...	@@ -988,28 +988,184 @@
988	988
989	989	)))
990	990
991		-== 3.3  Set Interrupt Mode ==
	997	+== 3.3  Get Firmware Version Info ==
992	992
993		-Feature, Set Interrupt mode for GPIO_EXIT.
	999	+Feature: use downlink to get firmware version.
994	994
995		-(% style="color:#037691" %)**Downlink Command: AT+INTMOD**
	1001	+(% style="color:#037691" %)**Downlink Command: 0x26**
996	996
997		-[[image:image-20220610105907-1.png]]
	1003	+[[image:image-20220607171917-10.png]]
998	998
	1005	+* Reply to the confirmation package: 26 01
	1006	+* Reply to non-confirmed packet: 26 00
999	999
1000		-(% style="color:#037691" %)**Downlink Command: 0x06**
	1008	+Device will send an uplink after got this downlink command. With below payload:
1001	1001
1002		-Format: Command Code (0x06) followed by 3 bytes.
	1010	+Configures info payload:
1003	1003
1004		-This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
	1012	+(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
	1013	+|=(((
	1014	+**Size(bytes)**
	1015	+)))|=**1**|=**1**|=**1**|=**1**|=**1**|=**5**|=**1**
	1016	+|**Value**|Software Type|(((
	1017	+Frequency
1005	1005
1006		-* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
1007		-* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	1019	+Band
	1020	+)))|Sub-band|(((
	1021	+Firmware
1008	1008
	1023	+Version
	1024	+)))|Sensor Type|Reserve|(((
	1025	+[[Message Type>>||anchor="H2.3.7A0MessageType"]]
	1026	+Always 0x02
	1027	+)))
1009	1009
	1029	+**Software Type**: Always 0x03 for LLDS12
1010	1010
1011	1011
	1032	+**Frequency Band**:
1012	1012
	1034	+*0x01: EU868
	1035	+
	1036	+*0x02: US915
	1037	+
	1038	+*0x03: IN865
	1039	+
	1040	+*0x04: AU915
	1041	+
	1042	+*0x05: KZ865
	1043	+
	1044	+*0x06: RU864
	1045	+
	1046	+*0x07: AS923
	1047	+
	1048	+*0x08: AS923-1
	1049	+
	1050	+*0x09: AS923-2
	1051	+
	1052	+*0xa0: AS923-3
	1053	+
	1054	+
	1055	+**Sub-Band**: value 0x00 ~~ 0x08
	1056	+
	1057	+
	1058	+**Firmware Version**: 0x0100, Means: v1.0.0 version
	1059	+
	1060	+
	1061	+**Sensor Type**:
	1062	+
	1063	+0x01: LSE01
	1064	+
	1065	+0x02: LDDS75
	1066	+
	1067	+0x03: LDDS20
	1068	+
	1069	+0x04: LLMS01
	1070	+
	1071	+0x05: LSPH01
	1072	+
	1073	+0x06: LSNPK01
	1074	+
	1075	+0x07: LLDS12
	1076	+
	1077	+
	1078	+
	1079	+= 5.  Battery & How to replace =
	1080	+
	1081	+== 5.1  Battery Type ==
	1082	+
	1083	+(((
	1084	+LLDS12 is equipped with a [[8500mAH ER26500 Li-SOCI2 battery>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]. The battery is un-rechargeable battery with low discharge rate targeting for 8~~10 years use. This type of battery is commonly used in IoT target for long-term running, such as water meter.
	1085	+)))
	1086	+
	1087	+(((
	1088	+The discharge curve is not linear so can’t simply use percentage to show the battery level. Below is the battery performance.
	1089	+)))
	1090	+
	1091	+[[image:1654593587246-335.png]]
	1092	+
	1093	+
	1094	+Minimum Working Voltage for the LLDS12:
	1095	+
	1096	+LLDS12:  2.45v ~~ 3.6v
	1097	+
	1098	+
	1099	+
	1100	+== 5.2  Replace Battery ==
	1101	+
	1102	+(((
	1103	+Any battery with range 2.45 ~~ 3.6v can be a replacement. We recommend to use Li-SOCl2 Battery.
	1104	+)))
	1105	+
	1106	+(((
	1107	+And make sure the positive and negative pins match.
	1108	+)))
	1109	+
	1110	+
	1111	+
	1112	+== 5.3  Power Consumption Analyze ==
	1113	+
	1114	+(((
	1115	+Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
	1116	+)))
	1117	+
	1118	+(((
	1119	+Instruction to use as below:
	1120	+)))
	1121	+
	1122	+
	1123	+**Step 1**: Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from:
	1124	+
	1125	+[[https:~~/~~/www.dragino.com/downloads/index.pHp?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
	1126	+
	1127	+
	1128	+**Step 2**: Open it and choose
	1129	+
	1130	+* Product Model
	1131	+* Uplink Interval
	1132	+* Working Mode
	1133	+
	1134	+And the Life expectation in difference case will be shown on the right.
	1135	+
	1136	+[[image:1654593605679-189.png]]
	1137	+
	1138	+
	1139	+The battery related documents as below:
	1140	+
	1141	+* (((
	1142	+[[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
	1143	+)))
	1144	+* (((
	1145	+[[Lithium-Thionyl Chloride Battery  datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
	1146	+)))
	1147	+* (((
	1148	+[[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
	1149	+)))
	1150	+
	1151	+[[image:image-20220607172042-11.png]]
	1152	+
	1153	+
	1154	+
	1155	+=== 5.3.1  ​Battery Note ===
	1156	+
	1157	+(((
	1158	+The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
	1159	+)))
	1160	+
	1161	+
	1162	+
	1163	+=== ​5.3.2  Replace the battery ===
	1164	+
	1165	+(((
	1166	+You can change the battery in the LLDS12.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
	1167	+)))
	1168	+
	1169	+(((
	1170	+The default battery pack of LLDS12 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
	1171	+)))
	1172	+
	1173	+
	1174	+
1013	1013	= 6.  Use AT Command =
1014	1014
1015	1015	== 6.1  Access AT Commands ==
...	...	@@ -1086,10 +1086,10 @@
1086	1086
1087	1087
1088	1088
1089		-= 6.  Order Info =
	1251	+= 9.  Order Info =
1090	1090
1091	1091
1092		-Part Number: (% style="color:blue" %)**LDDS75-XX-YY**
	1254	+Part Number: (% style="color:blue" %)**LLDS12-XX**
1093	1093
1094	1094
1095	1095	(% style="color:blue" %)**XX**(%%): The default frequency band
...	...	@@ -1103,19 +1103,12 @@
1103	1103	* (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
1104	1104	* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
1105	1105
1106		-(% style="color:blue" %)**YY**(%%): Battery Option
	1268	+= 10. ​ Packing Info =
1107	1107
1108		-* **(% style="color:red" %)4**(%%): 4000mAh battery
1109		-* **(% style="color:red" %)8**(%%): 8500mAh battery
1110	1110
1111		-
1112		-
1113		-= 7. ​ Packing Info =
1114		-
1115		-
1116	1116	**Package Includes**:
1117	1117
1118		-* LDDS75 LoRaWAN Distance Detection Sensor x 1
	1273	+* LLDS12 LoRaWAN LiDAR Distance Sensor x 1
1119	1119
1120	1120	**Dimension and weight**:
1121	1121
...	...	@@ -1124,9 +1124,7 @@
1124	1124	* Package Size / pcs : cm
1125	1125	* Weight / pcs : g
1126	1126
	1282	+= 11.  ​Support =
1127	1127
1128		-
1129		-= 8.  ​Support =
1130		-
1131	1131	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
1132	1132	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]].