Changes for page LDDS45 - LoRaWAN Distance Detection Sensor User Manual

Last modified by Mengting Qiu on 2025/02/26 15:04

From version < 147.5 >

edited by Xiaoling
on 2022/06/10 17:41

To version < 148.2 >

edited by Xiaoling
on 2022/06/10 17:48

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Attachments (0 modified, 1 added, 0 removed)
- image-20220610174836-8.png

Details

Page properties

Content

@@ -970,8 +970,6 @@
  [[image:image-20220610173409-7.png]]
--
--
  (((
  (% style="color:#037691" %)**Downlink Command: 0x01**
  )))
@@ -994,10 +994,9 @@
  Feature, Set Interrupt mode for GPIO_EXIT.
--
  (% style="color:#037691" %)**Downlink Command: AT+INTMOD**
--[[image:image-20220610105907-1.png]]
++[[image:image-20220610174836-8.png]]
  (% style="color:#037691" %)**Downlink Command: 0x06**
@@ -1010,146 +1010,18 @@
  * Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
--= 5.  Battery & How to replace =
--== 5.1  Battery Type ==
++= 4.  FAQ =
--(((
--LLDS12 is equipped with a [[8500mAH ER26500 Li-SOCI2 battery>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]. The battery is un-rechargeable battery with low discharge rate targeting for 8~~10 years use. This type of battery is commonly used in IoT target for long-term running, such as water meter.
--)))
++== 4.1  How to change the LoRa Frequency Bands/Region ==
--(((
--The discharge curve is not linear so can’t simply use percentage to show the battery level. Below is the battery performance.
--)))
--
--[[image:1654593587246-335.png]]
--
--
--Minimum Working Voltage for the LLDS12:
--
--LLDS12:  2.45v ~~ 3.6v
--
--
--
--== 5.2  Replace Battery ==
--
--(((
--Any battery with range 2.45 ~~ 3.6v can be a replacement. We recommend to use Li-SOCl2 Battery.
--)))
--
--(((
--And make sure the positive and negative pins match.
--)))
--
--
--
--== 5.3  Power Consumption Analyze ==
--
--(((
--Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
--)))
--
--(((
--Instruction to use as below:
--)))
--
--
--**Step 1**: Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from:
--
--[[https:~~/~~/www.dragino.com/downloads/index.pHp?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
--
--
--**Step 2**: Open it and choose
--
--* Product Model
--* Uplink Interval
--* Working Mode
--
--And the Life expectation in difference case will be shown on the right.
--
--[[image:1654593605679-189.png]]
--
--
--The battery related documents as below:
--
--* (((
--[[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
--)))
--* (((
--[[Lithium-Thionyl Chloride Battery  datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
--)))
--* (((
--[[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
--)))
--
--[[image:image-20220607172042-11.png]]
--
--
--
--=== 5.3.1  Battery Note ===
--
--(((
--The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
--)))
--
--
--
--=== 5.3.2  Replace the battery ===
--
--(((
--You can change the battery in the LLDS12.The type of battery is not limited as long as the output is between 3v to 3.6v.  On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
--)))
--
--(((
--The default battery pack of LLDS12 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
--)))
--
--
--
--= 6.  Use AT Command =
--
--== 6.1  Access AT Commands ==
--
--LLDS12 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LLDS12 for using AT command, as below.
--
--[[image:1654593668970-604.png]]
--
--**Connection:**
--
--(% style="background-color:yellow" %)** USB TTL GND <~-~-~-~-> GND**
--
--(% style="background-color:yellow" %)** USB TTL TXD  <~-~-~-~-> UART_RXD**
--
--(% style="background-color:yellow" %)** USB TTL RXD  <~-~-~-~-> UART_TXD**
--
--
--(((
--(((
--In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LLDS12.
--)))
--
--(((
--LLDS12 will output system info once power on as below:
--)))
--)))
--
--
-- [[image:1654593712276-618.png]]
--
--Valid AT Command please check [[Configure Device>>||anchor="H4.A0ConfigureLLDS12viaATCommandorLoRaWANDownlink"]].
--
--
--= 7.  FAQ =
--
--== 7.1  How to change the LoRa Frequency Bands/Region ==
--
  You can follow the instructions for [[how to upgrade image>>||anchor="H2.8A0200BFirmwareChangeLog"]].
  When downloading the images, choose the required image file for download.
--= 8.  Trouble Shooting =
++= 5.  Trouble Shooting =
--== 8.1  AT Commands input doesn’t work ==
++== 5.1  AT Commands input doesn’t work ==
  (((
@@ -1157,7 +1157,7 @@
  )))
--== 8.2  Significant error between the output distant value of LiDAR and actual distance ==
++== 5.2  Significant error between the output distant value of LiDAR and actual distance ==
  (((
@@ -1182,10 +1182,10 @@
--= 9.  Order Info =
++= 6.  Order Info =
--Part Number: (% style="color:blue" %)**LLDS12-XX**
++Part Number: (% style="color:blue" %)**LDDS75-XX-YY**
  (% style="color:blue" %)**XX**(%%): The default frequency band
@@ -1199,12 +1199,18 @@
  * (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
--= 10.  Packing Info =
++(% style="color:blue" %)**YY**(%%): Battery Option
++* (% style="color:red" %)**4**(%%): 4000mAh battery
++* (% style="color:red" %)**8**(%%): 8500mAh battery
++
++= 7.  Packing Info =
++
++
  **Package Includes**:
--* LLDS12 LoRaWAN LiDAR Distance Sensor x 1
++* LDDS75 LoRaWAN Distance Detection Sensor x 1
  **Dimension and weight**:
@@ -1213,7 +1213,8 @@
  * Package Size / pcs : cm
  * Weight / pcs : g
--= 11.  Support =
++= 8.  Support =
++
  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]].

image-20220610174836-8.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+34.3 KB

Content

Changes for page LDDS45 - LoRaWAN Distance Detection Sensor User Manual

Summary

Details

Applications

Navigation