Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -57,7 +57,6 @@
57	57	* IP66 Waterproof Enclosure
58	58	* 4000mAh or 8500mAh Battery for long term use
59	59
60		-
61	61	== 1.3  Specification ==
62	62
63	63	=== 1.3.1  Rated environmental conditions ===
...	...	@@ -98,7 +98,6 @@
98	98	* Sewer
99	99	* Bottom water level monitoring
100	100
101		-
102	102	== 1.6  Pin mapping and power on ==
103	103
104	104
...	...	@@ -239,7 +239,6 @@
239	239	* If the sensor value is 0x0000, it means system doesn’t detect ultrasonic sensor.
240	240	* If the sensor value lower than 0x0118 (280mm), the sensor value will be invalid. Since v1.1.4, all value lower than 280mm will be set to 0x0014(20mm) which means the value is invalid.
241	241
242		-
243	243	=== 2.3.3  Interrupt Pin ===
244	244
245	245	This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H4.2A0SetInterruptMode"]] for the hardware and software set up.
...	...	@@ -809,7 +809,6 @@
809	809	* Solid ON for 5 seconds once device successful Join the network.
810	810	* Blink once when device transmit a packet.
811	811
812		-
813	813	== 2.8  ​Firmware Change Log ==
814	814
815	815
...	...	@@ -828,7 +828,7 @@
828	828	[[image:image-20220610172003-2.png]]
829	829
830	830
831		-== 2.10  Battery Analysis ==
	827	+== 2.10  Battery Analysis ==
832	832
833	833	=== 2.10.1  Battery Type ===
834	834
...	...	@@ -974,109 +974,44 @@
974	974	[[image:image-20220610173409-7.png]]
975	975
976	976
977		-
978		-
979	979	(((
980		-(% style="color:#037691" %)**Downlink Command: 0x06**
	974	+(% style="color:#037691" %)**Downlink Command: 0x01**
981	981	)))
982	982
983	983	(((
984		-Format: Command Code (0x06) followed by 3 bytes.
985		-)))
986		-
987	987	(((
988		-This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
989		-)))
	979	+Format: Command Code (0x01) followed by 3 bytes time value.
990	990
991		-* (((
992		-Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	981	+If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
	982	+
	983	+* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	984	+* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
993	993	)))
994		-* (((
995		-Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
996		-)))
997	997
998		-== 3.3  Get Firmware Version Info ==
999	999
1000		-Feature: use downlink to get firmware version.
1001		-
1002		-(% style="color:#037691" %)**Downlink Command: 0x26**
1003		-
1004		-[[image:image-20220607171917-10.png]]
1005		-
1006		-* Reply to the confirmation package: 26 01
1007		-* Reply to non-confirmed packet: 26 00
1008		-
1009		-Device will send an uplink after got this downlink command. With below payload:
1010		-
1011		-Configures info payload:
1012		-
1013		-(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
1014		-|=(((
1015		-**Size(bytes)**
1016		-)))|=**1**|=**1**|=**1**|=**1**|=**1**|=**5**|=**1**
1017		-|**Value**|Software Type|(((
1018		-Frequency
1019		-
1020		-Band
1021		-)))|Sub-band|(((
1022		-Firmware
1023		-
1024		-Version
1025		-)))|Sensor Type|Reserve|(((
1026		-[[Message Type>>||anchor="H2.3.7A0MessageType"]]
1027		-Always 0x02
	988	+
1028	1028	)))
1029	1029
1030		-**Software Type**: Always 0x03 for LLDS12
	991	+== 3.3  Set Interrupt Mode ==
1031	1031
	993	+Feature, Set Interrupt mode for GPIO_EXIT.
1032	1032
1033		-**Frequency Band**:
1034	1034
1035		-*0x01: EU868
	996	+(% style="color:#037691" %)**Downlink Command: AT+INTMOD**
1036	1036
1037		-*0x02: US915
	998	+[[image:image-20220610105907-1.png]]
1038	1038
1039		-*0x03: IN865
1040	1040
1041		-*0x04: AU915
	1001	+(% style="color:#037691" %)**Downlink Command: 0x06**
1042	1042
1043		-*0x05: KZ865
	1003	+Format: Command Code (0x06) followed by 3 bytes.
1044	1044
1045		-*0x06: RU864
	1005	+This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
1046	1046
1047		-*0x07: AS923
	1007	+* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	1008	+* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1048	1048
1049		-*0x08: AS923-1
1050	1050
1051		-*0x09: AS923-2
1052		-
1053		-*0xa0: AS923-3
1054		-
1055		-
1056		-**Sub-Band**: value 0x00 ~~ 0x08
1057		-
1058		-
1059		-**Firmware Version**: 0x0100, Means: v1.0.0 version
1060		-
1061		-
1062		-**Sensor Type**:
1063		-
1064		-0x01: LSE01
1065		-
1066		-0x02: LDDS75
1067		-
1068		-0x03: LDDS20
1069		-
1070		-0x04: LLMS01
1071		-
1072		-0x05: LSPH01
1073		-
1074		-0x06: LSNPK01
1075		-
1076		-0x07: LLDS12
1077		-
1078		-
1079		-
1080	1080	= 5.  Battery & How to replace =
1081	1081
1082	1082	== 5.1  Battery Type ==