<
From version < 147.2 >
edited by Xiaoling
on 2022/06/10 17:34
To version < 147.4 >
edited by Xiaoling
on 2022/06/10 17:40
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -977,106 +977,44 @@
977 977  
978 978  
979 979  (((
980 -(% style="color:#037691" %)**Downlink Command: 0x06**
980 +(% style="color:#037691" %)**Downlink Command: 0x01**
981 981  )))
982 982  
983 983  (((
984 -Format: Command Code (0x06) followed by 3 bytes.
985 -)))
986 -
987 987  (((
988 -This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
989 -)))
985 +Format: Command Code (0x01) followed by 3 bytes time value.
990 990  
991 -* (((
992 -Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
987 +If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
988 +
989 +* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
990 +* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
993 993  )))
994 -* (((
995 -Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
996 -)))
997 997  
998 -== 3.3  Get Firmware Version Info ==
999 999  
1000 -Feature: use downlink to get firmware version.
1001 -
1002 -(% style="color:#037691" %)**Downlink Command: 0x26**
1003 -
1004 -[[image:image-20220607171917-10.png]]
1005 -
1006 -* Reply to the confirmation package: 26 01
1007 -* Reply to non-confirmed packet: 26 00
1008 -
1009 -Device will send an uplink after got this downlink command. With below payload:
1010 -
1011 -Configures info payload:
1012 -
1013 -(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
1014 -|=(((
1015 -**Size(bytes)**
1016 -)))|=**1**|=**1**|=**1**|=**1**|=**1**|=**5**|=**1**
1017 -|**Value**|Software Type|(((
1018 -Frequency
1019 -
1020 -Band
1021 -)))|Sub-band|(((
1022 -Firmware
1023 -
1024 -Version
1025 -)))|Sensor Type|Reserve|(((
1026 -[[Message Type>>||anchor="H2.3.7A0MessageType"]]
1027 -Always 0x02
994 +
1028 1028  )))
1029 1029  
1030 -**Software Type**: Always 0x03 for LLDS12
997 +== 3.3  Set Interrupt Mode ==
1031 1031  
999 +Feature, Set Interrupt mode for GPIO_EXIT.
1032 1032  
1033 -**Frequency Band**:
1034 1034  
1035 -*0x01: EU868
1002 +(% style="color:#037691" %)**Downlink Command: AT+INTMOD**
1036 1036  
1037 -*0x02: US915
1004 +[[image:image-20220610105907-1.png]]
1038 1038  
1039 -*0x03: IN865
1040 1040  
1041 -*0x04: AU915
1007 +**Downlink Command: 0x06**
1042 1042  
1043 -*0x05: KZ865
1009 +Format: Command Code (0x06) followed by 3 bytes.
1044 1044  
1045 -*0x06: RU864
1011 +This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
1046 1046  
1047 -*0x07: AS923
1013 +* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
1014 +* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1048 1048  
1049 -*0x08: AS923-1
1050 1050  
1051 -*0x09: AS923-2
1052 1052  
1053 -*0xa0: AS923-3
1054 -
1055 -
1056 -**Sub-Band**: value 0x00 ~~ 0x08
1057 -
1058 -
1059 -**Firmware Version**: 0x0100, Means: v1.0.0 version
1060 -
1061 -
1062 -**Sensor Type**:
1063 -
1064 -0x01: LSE01
1065 -
1066 -0x02: LDDS75
1067 -
1068 -0x03: LDDS20
1069 -
1070 -0x04: LLMS01
1071 -
1072 -0x05: LSPH01
1073 -
1074 -0x06: LSNPK01
1075 -
1076 -0x07: LLDS12
1077 -
1078 -
1079 -
1080 1080  = 5.  Battery & How to replace =
1081 1081  
1082 1082  == 5.1  Battery Type ==
Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0