Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -804,9 +804,6 @@
804	804	* The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
805	805	* Blink once when device transmit a packet.
806	806
807		-
808		-
809		-
810	810	== 2.8  ​Firmware Change Log ==
811	811
812	812
...	...	@@ -878,81 +878,56 @@
878	878	* The sensor window is made by Acrylic. Don’t touch it with alcohol material. This will destroy the sensor window.
879	879
880	880
	878	+
881	881	= 4.  Configure LLDS12 via AT Command or LoRaWAN Downlink =
882	882
883	883	(((
884		-(((
885	885	Use can configure LLDS12 via AT Command or LoRaWAN Downlink.
886	886	)))
887		-)))
888	888
889	889	* (((
890		-(((
891	891	AT Command Connection: See [[FAQ>>||anchor="H7.A0FAQ"]].
892	892	)))
893		-)))
894	894	* (((
895		-(((
896	896	LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]]
897	897	)))
898		-)))
899	899
900	900	(((
901		-(((
902	902
903		-)))
904	904
905		-(((
906	906	There are two kinds of commands to configure LLDS12, they are:
907	907	)))
908		-)))
909	909
910	910	* (((
911		-(((
912	912	(% style="color:#4f81bd" %)** General Commands**.
913	913	)))
914		-)))
915	915
916	916	(((
917		-(((
918	918	These commands are to configure:
919	919	)))
920		-)))
921	921
922	922	* (((
923		-(((
924	924	General system settings like: uplink interval.
925	925	)))
926		-)))
927	927	* (((
928		-(((
929	929	LoRaWAN protocol & radio related command.
930	930	)))
931		-)))
932	932
933	933	(((
934		-(((
935	935	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
936	936	)))
937		-)))
938	938
939	939	(((
940		-(((
941	941
942	942	)))
943		-)))
944	944
945	945	* (((
946		-(((
947	947	(% style="color:#4f81bd" %)** Commands special design for LLDS12**
948	948	)))
949		-)))
950	950
951	951	(((
952		-(((
953	953	These commands only valid for LLDS12, as below:
954	954	)))
955		-)))
956	956
957	957
958	958
...	...	@@ -965,6 +965,7 @@
965	965	[[image:image-20220607171554-8.png]]
966	966
967	967
	940	+
968	968	(((
969	969	(% style="color:#037691" %)**Downlink Command: 0x01**
970	970	)))
...	...	@@ -982,9 +982,11 @@
982	982	)))
983	983	* (((
984	984	Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
985		-)))
986	986
987	987
	960	+
	961	+)))
	962	+
988	988	== 4.2  Set Interrupt Mode ==
989	989
990	990	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -1013,7 +1013,6 @@
1013	1013	Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1014	1014	)))
1015	1015
1016		-
1017	1017	== 4.3  Get Firmware Version Info ==
1018	1018
1019	1019	Feature: use downlink to get firmware version.
...	...	@@ -1210,14 +1210,10 @@
1210	1210
1211	1211
1212	1212	(((
1213		-(((
1214	1214	In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LLDS12.
1215		-)))
1216	1216
1217		-(((
1218	1218	LLDS12 will output system info once power on as below:
1219	1219	)))
1220		-)))
1221	1221
1222	1222
1223	1223	[[image:1654593712276-618.png]]
...	...	@@ -1238,9 +1238,7 @@
1238	1238	== 8.1  AT Commands input doesn’t work ==
1239	1239
1240	1240
1241		-(((
1242	1242	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1243		-)))
1244	1244
1245	1245
1246	1246	== 8.2  Significant error between the output distant value of LiDAR and actual distance ==