Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -63,9 +63,6 @@
63	63	* Downlink to change configure
64	64	* 8500mAh Battery for long term use
65	65
66		-
67		-
68		-
69	69	== 1.3  Probe Specification ==
70	70
71	71	* Storage temperature ：-20℃~~75℃
...	...	@@ -81,9 +81,6 @@
81	81	* Material of enclosure - ABS+PC
82	82	* Wire length - 25cm
83	83
84		-
85		-
86		-
87	87	== 1.4  Probe Dimension ==
88	88
89	89
...	...	@@ -100,9 +100,6 @@
100	100	* Automatic control
101	101	* Sewer
102	102
103		-
104		-
105		-
106	106	== 1.6  Pin mapping and power on ==
107	107
108	108
...	...	@@ -309,9 +309,6 @@
309	309	|(% style="width:160px" %)0x01|(% style="width:163px" %)Normal Uplink|(% style="width:173px" %)[[Normal Uplink Payload>>||anchor="H2.3A0200BUplinkPayload"]]
310	310	|(% style="width:160px" %)0x02|(% style="width:163px" %)Reply configures info|(% style="width:173px" %)[[Configure Info Payload>>||anchor="H4.3A0GetFirmwareVersionInfo"]]
311	311
312		-
313		-
314		-
315	315	=== 2.3.8  Decode payload in The Things Network ===
316	316
317	317	While using TTN network, you can add the payload format to decode the payload.
...	...	@@ -480,9 +480,6 @@
480	480	* Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
481	481	* Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
482	482
483		-
484		-
485		-
486	486	=== 2.6.3  CN470-510 (CN470) ===
487	487
488	488	(((
...	...	@@ -889,6 +889,8 @@
889	889	* The LiDAR probe is cover by dirty things; the reading might be wrong. In this case, need to clean the probe.
890	890	* The sensor window is made by Acrylic. Don’t touch it with alcohol material. This will destroy the sensor window.
891	891
	877	+
	878	+
892	892	= 4.  Configure LLDS12 via AT Command or LoRaWAN Downlink =
893	893
894	894	(((
...	...	@@ -976,6 +976,7 @@
976	976	[[image:image-20220607171554-8.png]]
977	977
978	978
	966	+
979	979	(((
980	980	(% style="color:#037691" %)**Downlink Command: 0x01**
981	981	)))
...	...	@@ -998,7 +998,6 @@
998	998
999	999	)))
1000	1000
1001		-
1002	1002	== 4.2  Set Interrupt Mode ==
1003	1003
1004	1004	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -1027,7 +1027,6 @@
1027	1027	Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1028	1028	)))
1029	1029
1030		-
1031	1031	== 4.3  Get Firmware Version Info ==
1032	1032
1033	1033	Feature: use downlink to get firmware version.
...	...	@@ -1224,14 +1224,10 @@
1224	1224
1225	1225
1226	1226	(((
1227		-(((
1228	1228	In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LLDS12.
1229		-)))
1230	1230
1231		-(((
1232	1232	LLDS12 will output system info once power on as below:
1233	1233	)))
1234		-)))
1235	1235
1236	1236
1237	1237	[[image:1654593712276-618.png]]
...	...	@@ -1252,9 +1252,7 @@
1252	1252	== 8.1  AT Commands input doesn’t work ==
1253	1253
1254	1254
1255		-(((
1256	1256	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1257		-)))
1258	1258
1259	1259
1260	1260	== 8.2  Significant error between the output distant value of LiDAR and actual distance ==