Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -63,9 +63,6 @@
63	63	* Downlink to change configure
64	64	* 8500mAh Battery for long term use
65	65
66		-
67		-
68		-
69	69	== 1.3  Probe Specification ==
70	70
71	71	* Storage temperature ：-20℃~~75℃
...	...	@@ -81,9 +81,6 @@
81	81	* Material of enclosure - ABS+PC
82	82	* Wire length - 25cm
83	83
84		-
85		-
86		-
87	87	== 1.4  Probe Dimension ==
88	88
89	89
...	...	@@ -100,9 +100,6 @@
100	100	* Automatic control
101	101	* Sewer
102	102
103		-
104		-
105		-
106	106	== 1.6  Pin mapping and power on ==
107	107
108	108
...	...	@@ -883,81 +883,57 @@
883	883	* The LiDAR probe is cover by dirty things; the reading might be wrong. In this case, need to clean the probe.
884	884	* The sensor window is made by Acrylic. Don’t touch it with alcohol material. This will destroy the sensor window.
885	885
	877	+
	878	+
886	886	= 4.  Configure LLDS12 via AT Command or LoRaWAN Downlink =
887	887
888	888	(((
889		-(((
890	890	Use can configure LLDS12 via AT Command or LoRaWAN Downlink.
891	891	)))
892		-)))
893	893
894	894	* (((
895		-(((
896	896	AT Command Connection: See [[FAQ>>||anchor="H7.A0FAQ"]].
897	897	)))
898		-)))
899	899	* (((
900		-(((
901	901	LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]]
902	902	)))
903		-)))
904	904
905	905	(((
906		-(((
907	907
908		-)))
909	909
910		-(((
911	911	There are two kinds of commands to configure LLDS12, they are:
912	912	)))
913		-)))
914	914
915	915	* (((
916		-(((
917	917	(% style="color:#4f81bd" %)** General Commands**.
918	918	)))
919		-)))
920	920
921	921	(((
922		-(((
923	923	These commands are to configure:
924	924	)))
925		-)))
926	926
927	927	* (((
928		-(((
929	929	General system settings like: uplink interval.
930	930	)))
931		-)))
932	932	* (((
933		-(((
934	934	LoRaWAN protocol & radio related command.
935	935	)))
936		-)))
937	937
938	938	(((
939		-(((
940	940	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
941	941	)))
942		-)))
943	943
944	944	(((
945		-(((
946	946
947	947	)))
948		-)))
949	949
950	950	* (((
951		-(((
952	952	(% style="color:#4f81bd" %)** Commands special design for LLDS12**
953	953	)))
954		-)))
955	955
956	956	(((
957		-(((
958	958	These commands only valid for LLDS12, as below:
959	959	)))
960		-)))
961	961
962	962
963	963
...	...	@@ -970,6 +970,7 @@
970	970	[[image:image-20220607171554-8.png]]
971	971
972	972
	940	+
973	973	(((
974	974	(% style="color:#037691" %)**Downlink Command: 0x01**
975	975	)))
...	...	@@ -992,7 +992,6 @@
992	992
993	993	)))
994	994
995		-
996	996	== 4.2  Set Interrupt Mode ==
997	997
998	998	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -1021,7 +1021,6 @@
1021	1021	Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1022	1022	)))
1023	1023
1024		-
1025	1025	== 4.3  Get Firmware Version Info ==
1026	1026
1027	1027	Feature: use downlink to get firmware version.
...	...	@@ -1218,14 +1218,10 @@
1218	1218
1219	1219
1220	1220	(((
1221		-(((
1222	1222	In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LLDS12.
1223		-)))
1224	1224
1225		-(((
1226	1226	LLDS12 will output system info once power on as below:
1227	1227	)))
1228		-)))
1229	1229
1230	1230
1231	1231	[[image:1654593712276-618.png]]
...	...	@@ -1246,9 +1246,7 @@
1246	1246	== 8.1  AT Commands input doesn’t work ==
1247	1247
1248	1248
1249		-(((
1250	1250	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1251		-)))
1252	1252
1253	1253
1254	1254	== 8.2  Significant error between the output distant value of LiDAR and actual distance ==