Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -63,9 +63,6 @@
63	63	* Downlink to change configure
64	64	* 8500mAh Battery for long term use
65	65
66		-
67		-
68		-
69	69	== 1.3  Probe Specification ==
70	70
71	71	* Storage temperature ：-20℃~~75℃
...	...	@@ -81,9 +81,6 @@
81	81	* Material of enclosure - ABS+PC
82	82	* Wire length - 25cm
83	83
84		-
85		-
86		-
87	87	== 1.4  Probe Dimension ==
88	88
89	89
...	...	@@ -880,81 +880,57 @@
880	880	* The LiDAR probe is cover by dirty things; the reading might be wrong. In this case, need to clean the probe.
881	881	* The sensor window is made by Acrylic. Don’t touch it with alcohol material. This will destroy the sensor window.
882	882
	877	+
	878	+
883	883	= 4.  Configure LLDS12 via AT Command or LoRaWAN Downlink =
884	884
885	885	(((
886		-(((
887	887	Use can configure LLDS12 via AT Command or LoRaWAN Downlink.
888	888	)))
889		-)))
890	890
891	891	* (((
892		-(((
893	893	AT Command Connection: See [[FAQ>>||anchor="H7.A0FAQ"]].
894	894	)))
895		-)))
896	896	* (((
897		-(((
898	898	LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]]
899	899	)))
900		-)))
901	901
902	902	(((
903		-(((
904	904
905		-)))
906	906
907		-(((
908	908	There are two kinds of commands to configure LLDS12, they are:
909	909	)))
910		-)))
911	911
912	912	* (((
913		-(((
914	914	(% style="color:#4f81bd" %)** General Commands**.
915	915	)))
916		-)))
917	917
918	918	(((
919		-(((
920	920	These commands are to configure:
921	921	)))
922		-)))
923	923
924	924	* (((
925		-(((
926	926	General system settings like: uplink interval.
927	927	)))
928		-)))
929	929	* (((
930		-(((
931	931	LoRaWAN protocol & radio related command.
932	932	)))
933		-)))
934	934
935	935	(((
936		-(((
937	937	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
938	938	)))
939		-)))
940	940
941	941	(((
942		-(((
943	943
944	944	)))
945		-)))
946	946
947	947	* (((
948		-(((
949	949	(% style="color:#4f81bd" %)** Commands special design for LLDS12**
950	950	)))
951		-)))
952	952
953	953	(((
954		-(((
955	955	These commands only valid for LLDS12, as below:
956	956	)))
957		-)))
958	958
959	959
960	960
...	...	@@ -967,6 +967,7 @@
967	967	[[image:image-20220607171554-8.png]]
968	968
969	969
	940	+
970	970	(((
971	971	(% style="color:#037691" %)**Downlink Command: 0x01**
972	972	)))
...	...	@@ -989,7 +989,6 @@
989	989
990	990	)))
991	991
992		-
993	993	== 4.2  Set Interrupt Mode ==
994	994
995	995	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -1018,7 +1018,6 @@
1018	1018	Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1019	1019	)))
1020	1020
1021		-
1022	1022	== 4.3  Get Firmware Version Info ==
1023	1023
1024	1024	Feature: use downlink to get firmware version.
...	...	@@ -1215,14 +1215,10 @@
1215	1215
1216	1216
1217	1217	(((
1218		-(((
1219	1219	In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LLDS12.
1220		-)))
1221	1221
1222		-(((
1223	1223	LLDS12 will output system info once power on as below:
1224	1224	)))
1225		-)))
1226	1226
1227	1227
1228	1228	[[image:1654593712276-618.png]]
...	...	@@ -1243,9 +1243,7 @@
1243	1243	== 8.1  AT Commands input doesn’t work ==
1244	1244
1245	1245
1246		-(((
1247	1247	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1248		-)))
1249	1249
1250	1250
1251	1251	== 8.2  Significant error between the output distant value of LiDAR and actual distance ==