Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -875,81 +875,56 @@
875	875	* The sensor window is made by Acrylic. Don’t touch it with alcohol material. This will destroy the sensor window.
876	876
877	877
	878	+
878	878	= 4.  Configure LLDS12 via AT Command or LoRaWAN Downlink =
879	879
880	880	(((
881		-(((
882	882	Use can configure LLDS12 via AT Command or LoRaWAN Downlink.
883	883	)))
884		-)))
885	885
886	886	* (((
887		-(((
888	888	AT Command Connection: See [[FAQ>>||anchor="H7.A0FAQ"]].
889	889	)))
890		-)))
891	891	* (((
892		-(((
893	893	LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]]
894	894	)))
895		-)))
896	896
897	897	(((
898		-(((
899	899
900		-)))
901	901
902		-(((
903	903	There are two kinds of commands to configure LLDS12, they are:
904	904	)))
905		-)))
906	906
907	907	* (((
908		-(((
909	909	(% style="color:#4f81bd" %)** General Commands**.
910	910	)))
911		-)))
912	912
913	913	(((
914		-(((
915	915	These commands are to configure:
916	916	)))
917		-)))
918	918
919	919	* (((
920		-(((
921	921	General system settings like: uplink interval.
922	922	)))
923		-)))
924	924	* (((
925		-(((
926	926	LoRaWAN protocol & radio related command.
927	927	)))
928		-)))
929	929
930	930	(((
931		-(((
932	932	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
933	933	)))
934		-)))
935	935
936	936	(((
937		-(((
938	938
939	939	)))
940		-)))
941	941
942	942	* (((
943		-(((
944	944	(% style="color:#4f81bd" %)** Commands special design for LLDS12**
945	945	)))
946		-)))
947	947
948	948	(((
949		-(((
950	950	These commands only valid for LLDS12, as below:
951	951	)))
952		-)))
953	953
954	954
955	955
...	...	@@ -962,6 +962,7 @@
962	962	[[image:image-20220607171554-8.png]]
963	963
964	964
	940	+
965	965	(((
966	966	(% style="color:#037691" %)**Downlink Command: 0x01**
967	967	)))
...	...	@@ -984,8 +984,6 @@
984	984
985	985	)))
986	986
987		-
988		-
989	989	== 4.2  Set Interrupt Mode ==
990	990
991	991	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -1014,8 +1014,6 @@
1014	1014	Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1015	1015	)))
1016	1016
1017		-
1018		-
1019	1019	== 4.3  Get Firmware Version Info ==
1020	1020
1021	1021	Feature: use downlink to get firmware version.
...	...	@@ -1212,14 +1212,10 @@
1212	1212
1213	1213
1214	1214	(((
1215		-(((
1216	1216	In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LLDS12.
1217		-)))
1218	1218
1219		-(((
1220	1220	LLDS12 will output system info once power on as below:
1221	1221	)))
1222		-)))
1223	1223
1224	1224
1225	1225	[[image:1654593712276-618.png]]
...	...	@@ -1240,9 +1240,7 @@
1240	1240	== 8.1  AT Commands input doesn’t work ==
1241	1241
1242	1242
1243		-(((
1244	1244	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1245		-)))
1246	1246
1247	1247
1248	1248	== 8.2  Significant error between the output distant value of LiDAR and actual distance ==