Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -879,78 +879,52 @@
879	879	= 4.  Configure LLDS12 via AT Command or LoRaWAN Downlink =
880	880
881	881	(((
882		-(((
883	883	Use can configure LLDS12 via AT Command or LoRaWAN Downlink.
884	884	)))
885		-)))
886	886
887	887	* (((
888		-(((
889	889	AT Command Connection: See [[FAQ>>||anchor="H7.A0FAQ"]].
890	890	)))
891		-)))
892	892	* (((
893		-(((
894	894	LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]]
895	895	)))
896		-)))
897	897
898	898	(((
899		-(((
900	900
901		-)))
902	902
903		-(((
904	904	There are two kinds of commands to configure LLDS12, they are:
905	905	)))
906		-)))
907	907
908	908	* (((
909		-(((
910	910	(% style="color:#4f81bd" %)** General Commands**.
911	911	)))
912		-)))
913	913
914	914	(((
915		-(((
916	916	These commands are to configure:
917	917	)))
918		-)))
919	919
920	920	* (((
921		-(((
922	922	General system settings like: uplink interval.
923	923	)))
924		-)))
925	925	* (((
926		-(((
927	927	LoRaWAN protocol & radio related command.
928	928	)))
929		-)))
930	930
931	931	(((
932		-(((
933	933	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
934	934	)))
935		-)))
936	936
937	937	(((
938		-(((
939	939
940	940	)))
941		-)))
942	942
943	943	* (((
944		-(((
945	945	(% style="color:#4f81bd" %)** Commands special design for LLDS12**
946	946	)))
947		-)))
948	948
949	949	(((
950		-(((
951	951	These commands only valid for LLDS12, as below:
952	952	)))
953		-)))
954	954
955	955
956	956
...	...	@@ -963,6 +963,7 @@
963	963	[[image:image-20220607171554-8.png]]
964	964
965	965
	940	+
966	966	(((
967	967	(% style="color:#037691" %)**Downlink Command: 0x01**
968	968	)))
...	...	@@ -985,9 +985,6 @@
985	985
986	986	)))
987	987
988		-
989		-
990		-
991	991	== 4.2  Set Interrupt Mode ==
992	992
993	993	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -1016,9 +1016,6 @@
1016	1016	Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1017	1017	)))
1018	1018
1019		-
1020		-
1021		-
1022	1022	== 4.3  Get Firmware Version Info ==
1023	1023
1024	1024	Feature: use downlink to get firmware version.
...	...	@@ -1215,14 +1215,10 @@
1215	1215
1216	1216
1217	1217	(((
1218		-(((
1219	1219	In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LLDS12.
1220		-)))
1221	1221
1222		-(((
1223	1223	LLDS12 will output system info once power on as below:
1224	1224	)))
1225		-)))
1226	1226
1227	1227
1228	1228	[[image:1654593712276-618.png]]
...	...	@@ -1243,9 +1243,7 @@
1243	1243	== 8.1  AT Commands input doesn’t work ==
1244	1244
1245	1245
1246		-(((
1247	1247	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1248		-)))
1249	1249
1250	1250
1251	1251	== 8.2  Significant error between the output distant value of LiDAR and actual distance ==